Jeep Liberty KJ. Manual — part 1326
REAR VIEW MIRROR
REMOVAL
1. If equipped, disconnect mirror harness connector.
2. Loosen the mirror base setscrew.
3. Slide the mirror base upward and off the bracket.
INSTALLATION
INSTALLATION
1. Position the mirror base at the bracket and slide it
downward onto the support bracket.
2. Tighten the setscrew 1 N·m (15 in. lbs.) torque.
3. If equipped, connect mirror harness connector.
INSTALLATION - REAR VIEW MIRROR SUPPORT BRACKET
1. Mark the position for the mirror bracket on the outside of the windshield glass with a wax pencil.
2. Clean the bracket contact area on the glass. Use a mild powdered cleanser on a cloth saturated with isopropyl
(rubbing) alcohol. Finally, clean the glass with a paper towel dampened with alcohol.
3. Sand the surface on the support bracket with fine grit-sandpaper. Wipe the bracket surface clean with a paper
towel.
4. Apply accelerator to the surface on the bracket according to the following instructions:
a. Crush the vial to saturate the felt applicator.
b. Remove the paper sleeve.
c. Apply accelerator to the contact surface on the bracket.
d. Allow the accelerator to dry for five minutes.
e. Do not touch the bracket contact surface after the accelerator has been applied.
5. Apply adhesive accelerator to the bracket contact surface on the windshield glass. Allow the accelerator to dry
for one minute. Do not touch the glass contact surface after the accelerator has been applied.
23 - 204
INTERIOR
KJ
6. Install the bracket according to the following instructions:
a. Apply one drop of adhesive at the center of the bracket contact-surface on the windshield glass.
b. Apply an even coat of adhesive to the contact surface on the bracket.
c. Align the bracket with the marked position on the windshield glass.
d. Press and hold the bracket in place for at least one minute.
NOTE: Verify that the mirror support bracket is correctly aligned, because the adhesive will cure rapidly.
7. Allow the adhesive to cure for 8-10 minutes. Remove any excess adhesive with an alcohol-dampened cloth.
8. Allow the adhesive to cure for an additional 8-10 minutes before installing the mirror.
KJ
INTERIOR
23 - 205
PAINT
TABLE OF CONTENTS
page
page
PAINT
SPECIFICATIONS - PAINT CODES . . . . . . . . . . . . 207
PAINT CODE
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
BASE COAT/CLEAR COAT FINISH
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
PAINT TOUCH-UP
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
FINESSE SANDING/BUFFING & POLISHING
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
23 - 206
PAINT
KJ
PAINT
SPECIFICATIONS - PAINT CODES
NOTE: Because of late model changes to the available paint colors (Refer to VEHICLE DATA/VEHICLE
INFORMATION/VEHICLE CERTIFICATION LABEL - DESCRIPTION) or (Refer to VEHICLE DATA/VEHICLE
INFORMATION/BODY CODE PLATE - DESCRIPTION) for the correct paint codes for each vehicle. (Refer to
23 - BODY/PAINT/PAINT CODE - DESCRIPTION)
EXTERIOR COLORS
EXTERIOR COLOR
DAIMLERCHRYSLER CODE
Flame Read Clearcoat
PR4
Inferno Red Crystal Pearlcoat
ARJ
Light Khaki Metallic Clearcoat
AJC
Dark Khaki Pearlcoat
BJT
Deep Beryl Green Pearlcoat
CGV
Atlantic Blue Pearlcoat
ZBJ
Midnight Blue Pearlcoat
BB8
Bright Silver Metallic Clearcoat
WS2
Mineral Gray Metallic Clearcoat
CDM
Black Clearcoat
DX8
Stone White Clearcoat
SW1
INTERIOR COLORS
INTERIOR COLOR
DAIMLERCHRYSLER CODE
Slate Gray
D5
Khaki
J3
Khaki/Light Graystone
J1
Slate Gray/Light Slate Gray
DB
ACCESSORY COLORS
PART
COLOR
DAIMLERCHRYSLER CODE
Sport Accent Colors
Dark Medium Gray
BDL
Renegade Accent Colors
Medium Khaki
CJM
Dark Slate
CD7
KJ
PAINT
23 - 207
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст