Jeep Compass (2019 year). Instruction — part 31
SiriusXM Setup — If Equipped
After pressing the “SiriusXM Setup” button on the touch-
screen, the following settings will be available:
Setting Name
Selectable Options
Channel Skip
List Of Channels
NOTE:
SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude
undesirable channels while scanning. This feature allows you to select the channels you would like to skip.
Subscription Info
Sirius ID
NOTE:
New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your
radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription
Information screen to re-subscribe.
1. Press the “Subscription Info” button on the touchscreen to access the Subscription Information screen.
2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the
screen or visit the provider online.
484
MULTIMEDIA
Restore Settings
After pressing the “Restore Settings” button on the touch-
screen, the following settings will be available:
Setting Name
Selectable Options
Restore Settings
Yes
Cancel
NOTE:
When this feature is selected it will reset the audio settings to their default.
Clear Personal Data
After pressing the “Clear Personal Data” button on the
touchscreen, the following settings will be available:
Setting Name
Selectable Options
Clear Personal Data — If Equipped
OK
Cancel
NOTE:
When this feature is selected it will remove all personal data including Bluetooth devices and presets.
10
MULTIMEDIA
485
Customer Programmable Features — Uconnect
4C/4C NAV Settings
Press the “Apps
” button, then press the “Settings
” button on the touchscreen to display the menu
setting screen. In this mode the Uconnect system allows
you to access all of the available programmable features.
NOTE:
• Only one touchscreen area may be selected at a time.
• Depending on the vehicle’s options, feature settings may
vary.
When making a selection, press the button on the touch-
screen to enter the desired mode. Once in the desired
mode, press and release the preferred setting “option” until
a check-mark appears next to the setting, showing that
setting has been selected. Once the setting is complete,
press the “X” button on the touchscreen to close out of the
settings screen. Pressing the Up or Down Arrow button on
the right side of the screen will allow you to toggle up or
down through the available settings.
The following tables list the settings that may be found
within the Uconnect 4C/4C NAV radio, along with the
selectable options pertaining to each setting.
Uconnect 4C/4C NAV With 8.4–inch Display Buttons On
The Touchscreen And Buttons On The Faceplate
1 — Uconnect Buttons On The Touchscreen
2 — Uconnect Buttons On The Faceplate
486
MULTIMEDIA
Language
After pressing the “Language” button on the touchscreen,
the following settings will be available:
Setting Name
Selectable Options
Set Language
On
Off
NOTE:
When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa-
ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set
Language” button on the touchscreen, then press the desired language button on the touchscreen until a check-mark
appears next to the language, showing that setting has been selected.
Display
After pressing the “Display” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Display Mode
Manual
Auto
Display Brightness With Headlights ON
+
-
NOTE:
To make changes to the
⬙Display Brightness with Headlights ON⬙ setting, the headlights must be on and the interior
dimmer switch must not be in the
⬙party⬙ or ⬙parade⬙ positions.
10
MULTIMEDIA
487
Setting Name
Selectable Options
Display Brightness With Headlights OFF
+
-
NOTE:
To make changes to the
⬙Display Brightness with Headlights OFF⬙ setting, the headlights must be off and the interior
dimmer switch must not be in the
⬙party⬙ or ⬙parade⬙ positions.
Set Theme Options
On
Off
NOTE:
When in this display, you may select the theme for the display screen. To make your selection, press the
⬙Set Theme⬙
button on the touchscreen, then select the desired theme option button until a check-mark appears showing that the
setting has been selected.
Touchscreen Beep
On
Off
Control Screen Time-Out
On
Off
NOTE:
When the “Control Screen Time-Out” feature is selected, the Controls Screen will stay open for five seconds before
the screen times out. With the feature deselected, the screen will stay open until it is manually closed.
Navigation Turn-By-Turn In Cluster — If
Equipped
On
Off
NOTE:
When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the In-
strument Cluster Display as the vehicle approaches a designated turn within a programmed route.
Phone Pop-ups Displayed in Cluster
On
Off
488
MULTIMEDIA
Units
After pressing the “Units” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Units
US
Metric
Custom
NOTE:
• The “Metric” option changes the instrument cluster display to metric units of measure.
• The “Custom” option allows setting the “Fuel Consumption” (L/100km, or km/L), “Pressure” (kPa, or bar), and
“Temperature” (°C or °F) units of measure independently.
Voice
After pressing the “Voice” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Voice Response Length
Brief
Detailed
Show Command List
Always
With Help
Never
10
MULTIMEDIA
489
Clock
After pressing the “Clock” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Sync Time With GPS — If Equipped
On
Off
Set Time Hours
+
-
NOTE:
The “Set Time Hours” feature will allow you to adjust the hours. The “Sync time with GPS” button on the touch-
screen must be unchecked.
Set Time Minutes
+
-
NOTE:
The “Set Time Minutes” feature will allow you to adjust the minutes. The “Sync time with GPS” button on the touch-
screen must be unchecked.
Time Format
12hrs
24hrs
Show Time in Status Bar — If Equipped
On
Off
490
MULTIMEDIA
Safety & Driving Assistance
After pressing the “Safety & Driving Assistance” button on
the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Forward Collision Warning Sensitivity — If Equipped
Near
Medium
Far
NOTE:
The “Forward Collision Warning Plus (FCW+) Sensitivity” setting determines at what relative distance the vehicle
directly in front of you needs to be at, before the system will warn you of a possible collision with the vehicle directly
in front of you, based on the option is selected. “Far” will give you the most amount of reaction time, whereas
“Near” will give you the least amount of reaction time, based on the distance between the two vehicles.
Forward Collision Warning-Plus (FCW+)
Off
Only Warning
Warning + Active
Braking
NOTE:
The “Forward Collision Warning Plus (FCW+)” setting includes Advanced Brake Assist (ABA). The ABA applies ad-
ditional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision.
When the “OnlyWarning” option is selected a chime will sound alerting you of a possible collision with the vehicle in
front of you and more brake pressure is needed. When the “Warning + Active Braking” option is selected, it will ap-
ply the brakes to slow your vehicle in case of potential forward collision and sound an audible chime to alert you.
10
MULTIMEDIA
491
Setting Name
Selectable Options
LaneSense Warning — If Equipped
Early
Medium
Late
NOTE:
The “LaneSense Warning” setting determines at what distance the LaneSense system will warn you, through steering
wheel feedback, of a possible lane departure.
LaneSense Strength — If Equipped
Low
Med
High
ParkSense — If Equipped
Sound Only
Sound and Display
Rear ParkSense Volume
Low
Medium
High
Blind Spot Alert — If Equipped
Off
Lights
Lights & Chime
NOTE:
If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged,
the sensor may have become misaligned. Take your vehicle to your authorized dealer to verify sensor alignment. A
sensor that is misaligned will result in the BSM not operating to specification.
ParkView Backup Camera Active Guidelines
On
Off
ParkView Backup Camera Delay
On
Off
NOTE:
The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image
with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE. This delay will be canceled
if the vehicle’s speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, or the ignition is switched to
the OFF position.
492
MULTIMEDIA
Mirrors and Wipers
After pressing the “Mirrors and Wipers” button on the
touchscreen, the following settings will be available:
Setting Name
Selectable Options
Rain Sensing Auto Wipers
— If Equipped
On
Off
Brakes
After pressing the “Brakes” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Brake Service — If Equipped
Yes
No
NOTE:
This feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven system,
to command the electric park brake retraction, to service the rear foundation brakes (brake pads, calipers, rotors, etc.).
Auto Park Brake
On
Off
10
MULTIMEDIA
493
Lights
After pressing the “Lights” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Headlight Sensitivity
Level 1: minimum
sensitivity
Level 2: medium
sensitivity
Level 3: maximum sensitivity
NOTE:
The greater the sensitivity set, the less the external light variation required to turn on the lights (e.g. with a setting on
level 3 at sunset the headlights turn on earlier than in levels 1 and 2).
Headlight Off Delay
0 sec
30 sec
60 sec
90 sec
NOTE:
When this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the en-
gine is shut off.
Headlight Illumination On
Approach
0 sec
30 sec
60 sec
90 sec
Greeting Lights
On
Off
Daytime Running Lights
On
Off
494
MULTIMEDIA
Setting Name
Selectable Options
Cornering Lights
On
Off
NOTE:
When the “Cornering Lights” feature is selected, if the steering wheel rotation angle is large or the turn signal indica-
tors are on, a light (incorporated in the fog light) will turn on, on the relevant side to improve visibility at night.
Flash Lights With Lock — If
Equipped
On
Off
Interior Ambient Lights
+
-
NOTE:
The “Interior Ambient Lights” setting can also be adjusted by selecting any point on the scale between the “+” and
“-” buttons on the touchscreen.
Auto Dim High Beams — If
Equipped
On
Off
NOTE:
When the “Auto Dim High Beams” feature is selected, the high beam headlights will activate/deactivate automati-
cally under certain conditions.
10
MULTIMEDIA
495
Doors & Locks
After pressing the “Doors & Locks” button on the touch-
screen, the following settings will be available:
Setting Name
Selectable Options
Auto Unlock On Exit
On
Off
NOTE:
When the “Auto Unlock On Exit” feature is selected, all doors will unlock when the vehicle is stopped, the transmis-
sion is in the PARK or NEUTRAL position, and the driver’s door is opened.
Flash Lights With Lock
On
Off
Sound Horn With Lock — If Equipped
Off
1st Press
2nd Press
Sound Horn With Remote Start — If Equipped
On
Off
1st Press Of Key Fob Unlocks
Driver Door
All Doors
NOTE:
When
⬙Driver Door⬙ is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first
press of the key fob unlock button. You must press the key fob unlock button twice to unlock the passenger’s doors.
When
⬙All Doors⬙ is selected for 1st Press Of Key Fob Unlocks, all doors will unlock on the first press of the key fob
unlock button. If the vehicle is programmed 1st Press Of Key Fob Unlocks “All Doors,” all doors will unlock, no mat-
ter which Passive Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks “Driver Door” is pro-
grammed, only the driver’s door will unlock when the driver’s door is grasped. With Passive Entry, if 1st Press Of
Key Fob Unlocks “Driver Door” is programmed, touching the handle more than once will result in only the driver’s
door opening. If “Driver Door” is selected, once the driver door is opened, the interior door lock/unlock switch can
be used to unlock all doors (or use key fob).
496
MULTIMEDIA
Setting Name
Selectable Options
Passive Entry — If Equipped
On
Off
NOTE:
This feature allows you to lock and unlock the vehicles door(s) without having to push the key fob lock or unlock
buttons.
Auto-On Comfort Systems — If Equipped
After pressing the “Auto-On Comfort Systems” button on
the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Auto-On Driver Heated/Ventilated Seat & Steering Wheel
With Vehicle Start — If Equipped
Off
Remote Start
All Starts
NOTE:
When this feature is selected the driver’s heated seat and heated steering wheel will automatically turn on when tem-
peratures are below 40° F (4.4° C). When temperatures are above 80° F (26.7° C) the driver vented seat will turn on.
Engine Off Options
After pressing the “Engine Off Options” button on the
touchscreen, the following settings will be available:
Setting Name
Selectable Options
Headlight Off Delay — If Equipped
+
-
10
MULTIMEDIA
497
Radio
After pressing the
⬙Radio” on the touchscreen, the follow-
ing settings will be available:
Setting Name
Selectable Options
Radio Off Delay
0 min
20 min
NOTE:
When this feature is selected, the radio will stay on for 20 minutes, or until the first door is opened after the engine is
shut off.
Audio
After pressing the “Audio” button on the touchscreen, the
following settings will be available:
Setting Name
Selectable Options
Balance/Fade
Speaker Icon
NOTE:
When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon”
toward any location in the box.
498
MULTIMEDIA
Setting Name
Selectable Options
Equalizer
Bass
Mid
Treble
NOTE:
When in this display you may adjust the “Bass”, “Mid”, and “Treble” settings. Adjust the settings with the “+” and
“–” setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons on the
touchscreen. Bass/Mid/Treble also allow you to simply slide your finger up or down to change the setting as well as
press directly on the desired setting.
Speed Adjusted Volume
Off
1
2
3
Surround Sound — If Equipped
On
Off
AUX Volume Offset — If Equipped
+
-
NOTE:
This feature provides the ability to tune the audio level for portable devices connected through the AUX input.
10
MULTIMEDIA
499
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст