Engines Iveco C10,C13, Cursor 10, Cursor 13. Manual — part 15
Only for types F3AE0684P*E904 and F3AE0684N*E907 -
F3AE9687A*E001 - F3AE9687B*E001 - F3AE9687C*E001
Figure 73
Figure 74
81871
DIAGRAM OF ENGINE OIL SUMP FIXING SCREWS
TIGHTENING SEQUENCE
1
8
12
11
10
3
9
13
14
4
5
6
7
2
45362
Figure 75
104255
Tightening the fixing screws to the prescribed torque, mount:
-
the starter motor (1);
-
the control unit (2) and its support;
-
the oil dipstick (3) in the crankcase.
Check the state of the flexible elements of the control
unit support and change them if they have
deteriorated.
For all types except.
Fit the intake manifold (1) and tighten the fixing screws (2) to the
prescribed torque.
Figure 76
Figure 77
104253
Only for type F3AE0684N*E907 - F3AE9687A*E001 -
F3AE9687B*E001 - F3AE9687C*E001
Assemble the intake manifold (2), insert the locking screws (1)
and tighten to the specified torque.
104763
24
SECTION 3 - INDUSTRIAL APPLICATION
CURSOR ENGINES F3A
Base - May 2007
Fit the oil filters (1) on the relevant supports as follows:
-
oil the seals;
-
screw the filters down for the seals to make contact with
the supporting bases;
-
tighten the filters to a torque of 35 to 40 Nm.
Figure 78
Only for type F3AE0684P*E904
Mount the support (1) and tighten the fixing screws (3).
Connect the oil pipes (2) to the support (1) tightening the
fittings to the prescribed torque.
99362
Figure 79
For all types excluding F3AE0684P*E904
Mount the oil filters (1) on the support as follows:
-
oil the seal;
-
screw the filters down for the seals to make contact with
the supporting bases;
-
tighten the filters to a torque of 35 to 40 Nm.
99363
101960
Figure 80
Fit, with the respective gaskets.
-
the fuel pump (2);
-
fuel filter unit (3) and pipes (1);
-
connect the pipes (1) to the fuel pump (2).
104254
Figure 81
SECTION 3 - INDUSTRIAL APPLICATION
25
CURSOR ENGINES F3A
Base - May 2007
Figure 82
Figure 83
Figure 84
Only for type F3AE0684P*E904
Mount the cooler (2) with the relevant seal and tighten the
fixing screws (1) to the prescribed torque.
Tighten the screws (
←) fixing the clamps retaining the pipes
(3 and 4) to the spacer.
Mount the following with new seals:
-
exhaust manifold (2);
-
turbocharger (3);
-
oil pipe (1 and 4);
99258
455361
DIAGRAM OF HEAT EXCHANGER FIXING SCREWS
TIGHTENING SEQUENCE
104252
Figure 85
Figure 86
DIAGRAM OF EXHAUST MANIFOLD FIXING SCREWS
TIGHTENING SEQUENCE
DIAGRAM OF TURBOCHARGER FIXING SCREWS AND
NUTS TIGHTENING SEQUENCE
SEQUENCE: Preliminary tightening
4 - 3 - 1 - 2
Tightening
1 - 4 - 2 - 3
45359
1
8
6
3
2
7
6
3
4
7
6
3
2
7
5
4
8
5
2
8
5
4
1
1
45360
1
2
4
3
26
SECTION 3 - INDUSTRIAL APPLICATION
CURSOR ENGINES F3A
Base - May 2007
Figure 87
Figure 88
Fit, with the following parts:
-
automatic tightener support (1);
-
automatic tightener (2);
-
damper flywheel (3) and pulley beneath;
-
fixed tightener (5);
-
water pump (7);
-
the pulley (4);
-
pipe comprehensive of coolant (6);
-
thermostat assembly (8).
Figure 89
Mount the following, tightening the screws to the prescribed
torque:
-
the supports (1 and 3);
-
alternator (2).
For all types excluding F3AE0684P*E904
Using a suitable tool (3), work in the direction of the arrow on
the tightener (2) and mount the belt (1).
The take-up units are of the automatic type;
therefore no further adjustments are required after
assembly.
99360
104249
104251
DIAGRAM FOR FITTING BELT DRIVING FAN - WATER
PUMP - ALTERNATOR
1. Alternator - 2. Water pump - 3. Crankshaft -
4. Compressor.
Figure 90
101701
NOTE
SECTION 3 - INDUSTRIAL APPLICATION
27
CURSOR ENGINES F3A
Base - May 2007
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст