Engines Iveco C10,C13, Cursor 10, Cursor 13. Manual — part 16
Figure 91
Only for type F3AE0684P*E904
Fit the fan hub (6) and the compressor (5) with related
supports.
Using a suitable tool, operate on the belt take-up units (1) and
(3) and fit the belts (2) and (4).
104250
The take-up units are of the automatic type;
therefore no further adjustments are required after
assembly.
Figure 92
Fit the arm 99360585 onto the engine lifting hooks and hook
the arm onto the hoist.
Take out the screws fixing the brackets 99361036 to the
rotary stand. Lift the engine and remove the above-mentioned
brackets from it.
Complete engine assembly with the following parts, tightening
the fixing screws or nuts to the prescribed torque:
-
mount the drive (1);
-
mount the engine supports;
104247
Figure 93
-
mount the oil pressure adjuster valve (1).
104246
Figure 94
For all types except F3AE0684P*E904 and F3AE0684N*E907
Fit the engine support together with the air-conditioner
compressor (2).
Using a suitable tool (3), work in the direction of the arrow and
mount the belt (1).
Connect the engine electric cable to the sensors and control
unit.
Refill the engine with lubricating oil of the prescribed grade and
quantity.
99357
NOTE
28
SECTION 3 - INDUSTRIAL APPLICATION
CURSOR ENGINES F3A
Base - May 2007
A. Resistance for engine warming - B. Fuel filter clogged signalling switch - C. Fuel temperature sensor - D. Engine rpm sensor
on camshaft - E. Starter motor - G. Alternator - H. Air temperature/pressure sensor - I. Conditioner compressor - L. EDC 7
control unit - M. Connector on engine block for connection with electro-injectors - N. Water temperature for EDC 7 -
O. Water temperature sensor - P. Oil pressure/temperature transmitter - Q. Engine speed on flywheel sensor - R. Low oil
pressure transmitter.
ENGINE RIGHT-HAND SIDE VIEW
ENGINE LEFT-HAND SIDE VIEW
Figure 1
Figure 2
104263
104264
SECTION 3 - INDUSTRIAL APPLICATION
31
CURSOR ENGINES F3A
Base - May 2007
A. Resistance for engine warming - B. Fuel filter clogged signalling switch - C. Fuel temperature sensor - D. Engine rpm sensor
on camshaft - E. Starter motor - G. Alternator - H. Air temperature/pressure sensor - I. Conditioner compressor - L. EDC 7
control unit - M. Connector on engine block for connection with electro-injectors - N. Water temperature for EDC 7 -
O. Water temperature sensor - P. Oil pressure/temperature transmitter - Q. Engine speed on flywheel sensor -
R. Low oil pressure transmitter.
ENGINE RIGHT-HAND SIDE VIEW
ENGINE LEFT-HAND SIDE VIEW
Figure 3
Figure 4
104307
104308
32
SECTION 3 - INDUSTRIAL APPLICATION
CURSOR ENGINES F3A
Base - May 2007
A. Resistance for engine warming - B. Fuel filter clogged signalling switch - C. Fuel temperature sensor - D. Engine rpm sensor
on camshaft - E. Starter motor - G. Alternator - H. Air temperature/pressure sensor - I. Conditioner compressor - L. EDC 7
control unit - M. Connector on engine block for connection with electro-injectors - N. Water temperature for EDC 7 -
O. Water temperature sensor - P. Oil pressure/temperature transmitter - Q. Engine speed on flywheel sensor -
R. Low oil pressure transmitter.
ENGINE RIGHT-HAND SIDE VIEW
ENGINE LEFT-HAND SIDE VIEW
Figure 5
Figure 6
104765
104766
R
M
N
O
P
Q
SECTION 3 - INDUSTRIAL APPLICATION
33
CURSOR ENGINES F3A
Base - May 2007
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст