Engines Iveco C10,C13, Cursor 10, Cursor 13. Manual — part 50
ENGINE COMPLETION
Place gasket (4) on oil sump (1), position spacer (2) and fit the
sump onto the engine base by tightening screws (3) to the
specified torque, by complying with the tightening sequence
indicated in Figure 71.
Figure 69
Figure 70
101606
DIAGRAM OF ENGINE OIL SUMP FIXING SCREWS
TIGHTENING SEQUENCE
45362
101607
Figure 71
Fit the strainer (1) and tighten the lock screw to the torque
prescribed.
Loosen screws (3), then remove sump (1) complete with
spacer (2) and seal gasket (4).
For all types except: F3BE0684J*E902 - F3BE9687A*E001 -
F3BE9687B*E001 - F3BE9687C*E001
104784
Figure 72
Only for types: F3BE0684J*E902 - F3BE9687A*E001 -
F3BE9687B*E001 - F3BE9687C*E001
24
SECTION 3 - INDUSTRIAL APPLICATION
F3B CURSOR ENGINES
Base - May 2007
Figure 73
Figure 74
Figure 75
104310
Tightening the fixing screws to the prescribed torque, mount:
-
the starter motor (1);
-
the control unit (2) and its support;
-
the oil dipstick (3) in the crankcase.
Check the state of the flexible elements of the
control unit support and change them if they have
deteriorated.
Fit heat exchanger (2) with its respective gasket, then tighten
fastening screws (1) to the torque specified and according to
the sequence indicated in Figure 75.
Fit the oil filters (1) on the relevant supports as follows:
-
oil the seals;
-
screw the filters down for the seals to make contact with
the supporting bases;
-
tighten the filters to a torque of 35 to 40 Nm.
101605
45361
DIAGRAM OF HEAT EXCHANGER FIXING SCREWS
TIGHTENING SEQUENCE
Figure 76
Assemble the intake manifold (1) and tighten the locking screws
(2) to the specified torque.
116817
The intake joint may have different positions
depending on the type of engine.
NOTE
NOTE
SECTION 3 - INDUSTRIAL APPLICATION
25
F3B CURSOR ENGINES
Fit, with the respective gaskets.
-
the fuel pump (2);
-
fuel filter unit (3) with its respective pipes (1);
-
connect the pipes (1) to the fuel pump (2).
104254
Figure 77
Figure 78
Figure 79
Mount the following with new seals:
-
exhaust manifold (2);
-
turbocharger (3);
-
oil pipe (1 and 4);
Figure 80
DIAGRAM OF EXHAUST MANIFOLD FIXING SCREWS
TIGHTENING SEQUENCE
DIAGRAM OF TURBOCHARGER FIXING SCREWS AND
NUTS TIGHTENING SEQUENCE
SEQUENCE: Preliminary tightening
4 - 3 - 1 - 2
Tightening
1 - 4 - 2 - 3
45359
1
8
6
3
2
7
6
3
4
7
6
3
2
7
5
4
8
5
2
8
5
4
1
1
45360
1
2
4
3
104252
The position of the turbine varies according to the
equipment.
NOTE
26
SECTION 3 - INDUSTRIAL APPLICATION
F3B CURSOR ENGINES
Base - May 2007
Figure 81
Figure 82
Fit, with the following parts:
-
automatic tightener support (1);
-
automatic tightener (2);
-
damper flywheel (3) and pulley beneath;
-
fixed tightener (5);
-
water pump (7);
-
the pulley (4);
-
pipe comprehensive of coolant (6);
-
thermostat assembly (8).
Figure 83
Mount the following, tightening the screws to the prescribed
torque:
-
the supports (1 and 3);
-
alternator (2).
Using a suitable tool (3), work in the direction of the arrow on
the tightener (2) and mount the belt (1).
The tighteners are automatic, so there are no other
adjustments after assembly.
99360
104251
104249
DIAGRAM FOR FITTING BELT DRIVING FAN - WATER
PUMP - ALTERNATOR
1. Alternator - 2. Water pump - 3. Crankshaft -
4. Compressor.
Figure 84
101701
Only for type: F3BE0684J*E902
NOTE
SECTION 3 - INDUSTRIAL APPLICATION
27
F3B CURSOR ENGINES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст