Engine Iveco C10/C13/C78/Cursor 13/Cursor 78. Manual — part 47
For types F3AE0684D*B003 and F3AE0684E*B002 only,
using tool 99360314 (2), unscrew the oil filters (1).
Disconnect the fuel pipes (1) from the fuel pump (2).
Remove:
-
the fuel pump (2);
-
the fuel filter unit (3) and pipes (1).
Take out the screws (2) and remove the intake manifold (1).
Remove:
-
the starter motor (1);
-
the control unit (2) and its support;
-
the oil dipstick (3) from the crankcase.
Figure 13
Figure 14
Figure 15
Figure 16
99363
99263
99273
99264
10
SECTION 3 - INDUSTRIAL APPLICATION
60493
85480
60496
60497
-
Unscrew the screws (1) and remove the heat exchanger (4);
-
unscrew the screws (2) and remove the water line (3).
-
Unscrew the screws (2) and remove the gear (1) fitted
with phonic wheel.
-
Unscrew the screws (1); tighten one screw in a reaction
hole and remove the shoulder plate (2), remove the sheet
gasket.
Figure 17
Figure 18
Figure 19
Remove the rocker arm cover (1), take off the screws (2) and
remove: the cover (3), the filter (5) and the gaskets (4 and 6).
Take off the screws (8) and remove the blow-by case (7).
Figure 20
SECTION 3 - INDUSTRIAL APPLICATION
11
60498
60500
60499
60501
99365
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Unscrew the screws (2) and remove the transmission gear (1).
Stop the engine flywheel (3) rotation by means of tool
99360351 (1), unscrew the fixing screws (2) and remove the
engine flywheel.
Apply the extractor 99340054 (2) and pull out the seal
gasket (1).
Unscrew the screws (1) and take down the gearbox (2).
- To release lever stop springs.
- Loosen the screws and remove electric connections (2)
from the pump injector solenoid valves.
- Unscrew the screws (1) fixing the rocker arm shaft.
Figure 26
106219
Remove screws (3) and dismount double gear (2).
Remove securing screw and dismount articulated rod (5).
Dismount oil pump (4).
12
SECTION 3 - INDUSTRIAL APPLICATION
73533
60514
99366
60515
99268
81871
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Using tool 99360144 (3), constrain the blocks (4) to the
rockers (2).
Apply tool 99360553 (1) to the rocker holder shaft (5) and
remove the shaft (5) from the cylinder head.
- Unscrew the screws (2) fixing the brackets (3) and
remove the injectors (1).
- Fit the plugs 99360180 (1) instead of injectors.
- Remove the camshaft (2).
- Unscrew the fixing screws on the cylinder head (3).
- By means of metal ropes, lift the cylinder head (1).
- Remove the seal (2).
Undo the screws (2) and remove the engine oil sump (1)
together with the spacer (3) and the seal (4).
Valid for types:
F3AE0684D*B001
F3AE0684G*B003
F3AE0684D*B003
Valid for F3AE0684E*B002 and F3AE0684J*B902 only.
SECTION 3 - INDUSTRIAL APPLICATION
13
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст