Iveco Daily Euro 4. Manual — part 66
88343
88344
88340
88346
88347
Figure 209
Figure 210
Figure 211
Figure 212
Figure 213
Lubricate the new seal rings (1) with engine oil and fit them
on the covers (2).
Fit the covers (2) on the overhead, drive in the fastening
screws (3) and tighten them to the prescribed torque.
Lubricate the support pins of the suction camshafts (2) and
exhaust camshafts (4) and fit them on the overhead (1).
Fit the top skid (3) and drive in the nuts (4), then tighten them
to the prescribed torque.
Fit the shoulder plate (2) and drive in the screws (1), then
tighten them to the prescribed torque.
Position the camshafts (3 and 4) so that the pins 99360614
(1) can be inserted in the camshaft slots (2) through the
over-head threaded holes.
Rotate the driving shaft so that the tool 99360615 (1) can be
inserted in the shaft crank hole through the cylinder block
hole, in order to stop the engine in the timing system setting
condition.
AUXILIARY ORGAN CONTROLS
During this operation do not exchange the
assembly position of the shafts.
The suction camshaft can be recognised (2)
through the dowel (3) on the front side and the
retainer on the rear side.
In addition, take care not to damage the support
seats of the over-head shafts.
NOTE
256
F1C ENGINE
D
AILY
E
URO
4
88348
88277
88279
88278
88349
88276
Figure 214
Figure 215
Figure 216
Figure 217
Figure 218
Figure 219
Lubricate the seal rings (1 and 2) with engine oil and fit them
on the support (3).
Fit the support (1) and drive in the nuts (2), then tighten them
to the prescribed torque.
Fit the stem (3).
Stop the stem rotation (2) of the hydraulic power steering
pump by inserting in the latter the tool (3) and fastening the
tool on the support (1) by means of the screws (4).
Fit the gear (1) on the stem (3) of the hydraulic power
steering pump.
Drive in the screw (2) without locking it.
Lubricate the new seal rings (1 and 2) with engine oil and fit
them on the support (3).
Fit the support (1), drive in the nuts (2) and tighten them to
the prescribed torque.
Fit the control stem (3) of the high pressure pump.
F1C ENGINE
257
D
AILY
E
URO
Check the conditions of the fixed skids (1 and 3) and change
them if worn out.
Fit the skid (1) and drive in the fastening screws (2), then
tighten them to the prescribed torque.
Fit the skid (3) and drive in the fastening screws (4), then
tighten them to the prescribed torque.
88351
88274
88352
88353
Figure 220
Figure 221
Figure 222
Figure 223
Position the chain (1) on the gears (2, 3 and 5) and fit the gear
(3) on the stem (4) so that the chain (1) in tracts A and B is
tensioned.
Fit the stem with the drive gear (2) on the high pressure
pump control stem (1).
Drive in the fastening screw (3).
Cynder head refitting
Check that the mating surfaces of the cylinder head and
crankcase are clean.
Keep the cylinder head gasket clean.
Place the gasket (1) of the cylinder head with the thickness
given in section “Check piston protrusion”, with the “TOP”
sign facing the head.
It is essential to keep the gasket sealed in its package
until just before assembly.
88354
Figure 224
Mount the cylinder head (2).
Screw down the fixing screws (3) and tighten them, in three
successive stages, following the order and methods shown in
the following figure.
NOTE
α
The angle closure is done with tool 99395216 (1).
NOTE
258
F1C ENGINE
D
AILY
E
URO
4
88355
Figure 225
Diagram of the tightening sequence for the cylinder head
fixing screws:
- 1
st
phase: pre-tightening with torque wrench
•
screws 1-2-3-4-5-6 to a torque of 130 Nm;
•
screws 7-8-9-10 to a torque of 65 Nm.
- 2
nd
phase: angle closing
•
screws 1-2-3-4-5-6 90
°;
•
screws 7-8-9-10 90
°.
- 3
rd
phase: angle closing
•
screws 1-2-3-4-5-6 90
°;
•
screws 7-8-9-10 60
°.
- Screws A, to a torque of 25 Nm
Thoroughly clean the hydraulic tappets (2), lubricate them and
fit them in the cylinder head (3), positioning the rocker arms (1)
on the valves correctly.
Fit on the gasket (5).
Insert the two tools SP. 2264 (4) into the electro-injector seats
for subsequent centring of the overhead on the cylinder head.
Mount the overhead (1) together with the tools 99360614
(3) for the timing and tighten the fixing screws (2) to the
prescribed torque.
Take out the tools SP. 2264 (4).
Figure 226
88356
Figure 227
88357
TIMING SYSTEM CONTROL
Figure 228
88270
Fit the top fixed skid (1). Drive in the screws (2 and 3) and
tighten them to the prescribed torque.
Fit the rubber cap (4) of the new gasket and tighten it to the
prescribed torque.
F1C ENGINE
259
D
AILY
E
URO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст