Iveco Daily Euro 4. Manual — part 67
88359
88360
88361
88362
Figure 229
Figure 230
Figure 231
Figure 232
Figure 233
Position the chain (1) on the gear (5) and gear (2).
Mount the gear in such a way that fitting on aspiration valve
timing system shaft dowel makes slots A to result to be
positioned as in figure.
Position the chain (1) on the gear (2) and fit the latter on the
camshaft of the exhaust valves.
Drive in the fastening screw (4) with the washer (3) without
tightening it completely.
Check the conditions of the mobile skids (1 and 3), if worn
out change them.
Position the mobile skids (1 and 3) and clamp them on the
cylinder block by the pin (2) and tighten it to the prescribed
torque.
Drive in the chain hydraulic tightener (1) and lock it to the
prescribed torque.
Tighten the fastening screw of the gear (1) on the hydraulic
power steering control stem to the prescribed torque.
Drive in the fastening screw (4) with the washer (3) without
tightening it completely.
The chain arm (1) between the two gears must be
tensioned.
NOTE
88358
260
F1C ENGINE
D
AILY
E
URO
4
Fit a new gasket (5) in the cover (2).
Fit the cover (2), drive in the screws (1) and tighten them to
the prescribed torque.
Fit the phase sensor (4).
Drive in the fastening nut (3) and tighten it to the prescribed
torque.
88372
102127
88373
88374
Figure 235
Figure 236
Figure 237
Screw down hydraulic chain stretcher (2), then tighten it to
the specified torque.
Insert, through the opening on the overhead, a suitable
screwdriver, then press on moving shoe (4) fin (3) until chain
stretcher (2) piston (1) is pushed to its end of stroke.
Release moving shoe (4), and make sure that piston (1)
causes, by escaping from its seat, chain (5) to be subjected
to tension.
Tighten the fastening screw of the gear (1) on the suction
valve camshaft to the prescribed torque.
Make sure that the chain (3) in the tract between the gear
(2) and gear (4) is tensioned.
Tighten the fastening screw of the gear (2) on the exhaust
valve camshaft to the prescribed torque.
Remove tools 99360614 (1).
Figure 234
Stop the rotation of the high pressure pump control shaft (1)
by inserting the suitable wrench inside it.
90311
Chain stretcher (1) cannot be re-used for any
reason after it has been disassembled. Moreover, in
the event that piston (1) has been unintentionally made to
escape from chain stretcher (2), the latter must be replaced.
Chain stretcher reconditioning is not permitted.
NOTE
Figure 238
88370
Make sure that the chain (2) and the tract between the gear
(1) and gear (3) is tensioned.
Tighten the fastening screw of the stem with the drive gear
(1) on the high pressure pump control stem to the prescribed
torque.
Figure 239
F1C ENGINE
261
D
AILY
E
URO
88375
88377
88376
90156
107727
Figure 240
Figure 241
Figure 242
Figure 243
Figure 244
Position the joint (5) in the gear (6).
Fit the oil pump/depressor unit (4) by inserting a new gasket
(1).
Drive in the screws (2) and tighten them to the prescribed
torque.
Remove tool 99360615 (2).
Fit the cover (1) with a new gasket. Drive in the screws (2)
without tightening them completely.
Clean accurately the seat of the cover seal ring (1).
Drive in the element (2) of tool 99346258 in the driving shaft
tang.
Lubricate the tang of the driving shaft and the element
outside (2) and fit flush the new seal ring on this element (3).
Position the element (4) on element (2), lock the nut (5) until
fitting the seal ring (3) completely in the cover (1).
Fit a new centrifugal filter (1).
Fit a new snap ring (2).
Fit the cover (3), drive in the screws (4) and tighten them to
the prescribed torque.
Mount tool 99396030 (3), for centering cover (1), into
centrifugal filter seat and tighten screws (2) at prescribed
torque. Remove: 99346258 (4) and 99396039 (3) tools.
262
F1C ENGINE
D
AILY
E
URO
4
88379
107725
108431
107723
88260
Figure 245
Figure 246
Figure 247
Figure 248
Figure 249
Fit the water pump (2) with a new gasket.
Drive in the screws (1) and tighten them to the prescribed
torque.
Fit the electric magnet (3) of the cooling fan joint on the
water pump (6).
Drive in the nuts (2) and tighten them to the prescribed
torque.
Secure the electric cable to retaining clip (1).
Fit the pulley (4) and the hub (5).
Stop the rotation of water pump shaft (5) by means of an
Allen wrench (3) and a special lever. Screw down hub (1)
fastening nut (2). Use a suitable wrench (4) to tighten nut (2)
to the specified torque.
Drive in the oil level sensor (1) and tighten it to the
prescribed torque.
Fit the rev sensor (2), drive in the fastening screw (3) and
tighten it to the prescribed torque.
Fit the support (2), drive in the screws (1) and tighten them
to the prescribed torque.
88378
Stop the rotation of the engine flywheel (2) by means of tool
99360306 (1).
Fit the damper pulley (3). Drive in the screw (4) and tighten
it to the prescribed torque.
Figure 250
The nut (2) must be driven in anticlockwise (
→)
because its threading is left-handed.
NOTE
F1C ENGINE
263
D
AILY
E
URO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст