Iveco Daily. Manual — part 224
122/30
6 AS 300 VD TRANSMISSION
D
AILY
Revi - February 2005
Some modifications or repairs that affect the ESV1 system components, automatic transmission, require a calibration procedure.
The repairs that require this operation are detailed as follows:
-
Replacing the gearbox kit + control unit
-
Replacing the control unit only
-
Replacing the clutch actuator
-
Replacing the gearbox actuator
-
Replacing an electric motor of the gearbox actuator
-
Replacing the engaging fork
Replacing the gearbox wiring requires no calibration procedure.
NOTE
Calibration in case of replacement of the gearbox kit + control unit
The control unit must be programmed (no error in the memory) by providing the same with the vehicle data, e.g. axle ratio,
rolling radius, strength curve, etc.
Get connected to the vehicle by means of the diagnosis instrument, with the vehicle stationary, engine OFF and gearshift lever
in neutral.
Carry out the operations indicated by the instrument: key ON (engine ON), then the dedicated calibration procedure will be
started
→ ” Adaptation of touch Point.
Message “service” will appear on the display; the system in automatic mode will carry out the following operations:
- opening the clutch;
- engaging the 5
th
or 6
th
speed;
- he clutch closes three times searching for the point of initial slip (the vehicle will pick up three times);
- putting the lever in neutral;
- closing the clutch.
The procedure is interrupted when the engine is switched off.
Wait 10 seconds prior to the next KEY ON.
NOTE
When the procedure has been completed, check the control unit memory and verify that no error is found.
Calibration in case of replacement of the control unit
The control unit must be programmed by providing the same with the vehicle data, e.g. axle ratio, rolling radius, strength curve,
etc.
Get connected to the vehicle by means of the diagnosis instrument, with the vehicle stationary, engine OFF and gearshift lever
in neutral.
Carry out the operations indicated by the instrument: key ON (engine OFF), then the dedicated calibration procedures will
be started
→ Measurement of Maximum Clutch Travel
Transmission Self Adaptation
Message “service” will appear on the display; the system in automatic mode will carry out the aforesaid procedures. Upon
completion of this step, the engine will be started and the
→ Adaptation of touch Point calibration procedure will be started.
Message “service” will appear on the display; the system in automatic mode will carry out the following operations:
- opening the clutch;
- engaging the 5
th
or 6
th
speed;
- he clutch closes three times searching for the point of initial slip (the vehicle will pick up three times);
- putting the lever in neutral;
- closing the clutch.
The procedure is interrupted when the engine is switched off.
6 AS 300 VD TRANSMISSION
122/31
D
AILY
Wait 10 seconds prior to the next KEY ON.
NOTE
When the procedure has been completed, check the control unit memory and verify that no error is found.
Calibration in case of replacement of the clutch actuator
Clear the control unit error memory.
Get connected to the vehicle by means of the diagnosis instrument, with the vehicle stationary, engine OFF and gearshift lever
in neutral.
Carry out the operations indicated by the instrument: key ON (engine OFF), then the dedicated calibration procedure will be
started
→ Measurement of Maximum Clutch Travel.
Message “service” will appear on the display; the system in automatic mode will carry out the necessary operations. The
procedure will be interrupted when the engine is switched off.
Wait 10 seconds prior to the next KEY ON.
NOTE
When the procedure has been completed, check the control unit memory and verify that no error is found.
Calibration in case of replacement of the gearbox actuator or an electric motor of the gearbox
actuator
Clear the control unit error memory.
Get connected to the vehicle by means of the diagnosis instrument, with the vehicle stationary, engine OFF and gearshift lever
in neutral.
Carry out the operations indicated by the instrument: key ON (engine OFF), then the dedicated calibration procedure will be
started
→ Transmission Self Adaptation.
Message “service” will appear on the display; the system in automatic mode will carry out the necessary operations. The
procedure will be interrupted when the engine is switched off.
Wait 10 seconds prior to the next KEY ON.
NOTE
When the procedure has been completed, check the control unit memory and verify that no error is found.
Calibration in case of replacement of the clutch engaging/release fork
Clear the control unit error memory.
Get connected to the vehicle by means of the diagnosis instrument, with the vehicle stationary, engine OFF and gearshift lever
in neutral.
Carry out the operations indicated by the instrument: key ON (engine ON), then the dedicated calibration procedure will be
started
→ Adaptation of Touch Point.
Message “service” will appear on the display; the system in automatic mode will carry out the following operations:
- opening the clutch;
- engaging the 5
th
or 6
th
speed;
- the clutch closes three times searching for the point of initial slip (the vehicle will pick up three times);
- putting the lever in neutral;
- closing the clutch.
The procedure is interrupted when the engine is switched off.
Wait 10 seconds prior to the next KEY ON.
NOTE
When the procedure has been completed, check the control unit memory and verify that no error is found.
122/32
6 AS 300 VD TRANSMISSION
D
AILY
Revi - February 2005
POWER TAKE OFF
123
D
AILY
TRANSMISSION
Power take off
Page
SPECIFICATIONS AND DATA
125
. . . . . . . . . . . . .
TIGHTENING TORQUES
126
. . . . . . . . . . . . . . . . .
ASSEMBLY STANDARDS
127
. . . . . . . . . . . . . . . . .
POWER TAKE OFF ELECTRIC ACTUATOR
128
. .
- Description
128
. . . . . . . . . . . . . . . . . . . . . . . . . . .
- Operation
128
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст