KIA Ceed (2017 year). Instruction — part 36
JD PE eng 7.QXP
03.01.2017
17:22 Page 86
Maintenance
With AFLS
■ Type A
Front fog light aiming
1. Turn off the engine
The front fog lamp can be aimed as the
2. Turn the light switch to the low beam
same manner of the head lamps aiming.
position.
With the front fog lamps and battery nor-
3. Position the tires straight ahead with
mal condition, aim the front fog lamps. To
the steering wheel.
aim the front fog lamp up or down, turn the
4. Turn on the engine.
driver (1) clockwise or counterclockwise.
5. Inflate the tires to the specified pres-
sure and remove any loads from the
vehicle except the driver, spare tire,
and tools.
OJD075028
6. The vehicle should be placed on a flat
■ Type B
floor.
7. Draw vertical lines (Vertical lines pass-
ing through respective head lamp cen-
ters) and a horizontal line (Horizontal
line passing through center of head
lamps) on the screen.
8. With the head lamp and battery in nor-
mal condition, aim the head lamps so
the brightest portion falls on the hori-
zontal and vertical lines.
OJD075070
9. To aim the low beam left or right, turn
■ Type C
the driver
(1) clockwise or counter-
clockwise. To aim the low beam up or
down, turn the driver (2) clockwise or
counterclockwise. To aim the high
beam up or down, turn the driver (3)
clockwise or counterclockwise.
OJD073082
7 86
JD PE eng 7.QXP
03.01.2017
17:22 Page 87
Maintenance
Aiming point
< Ground Height >
< Distance between lamps >
OJD075051
H1 : Height between the head lamp bulb center and ground (Low beam)
H2 : Height between the head lamp bulb center and ground (High beam)
H3 : Height between the fog lamp bulb center and ground
W1 : Distance between the two head lamp bulbs centers (Low beam)
W2 : Distance between the two head lamp bulbs centers (High beam)
W3 : Distance between the two fog lamp bulbs centers
7 87
JD PE eng 7.QXP
03.01.2017
17:23 Page 88
Maintenance
■ 3,5 Door and Wagon
Unit: mm (in)
Vehicle
H3
W3
H1
H2
W1
W2
condition
FOG ONLY
FOG+DRL
FOG ONLY
FOG+DRL
Without
689/699/684
646/656/641
345/355/340
328/338/323
driver
(27.1)/(27.5)/(26.9)
(25.4)/(25.8)/(25.2)
(13.6)/(13.9)/(13.4)
(12.9)/(13.3)/(12.7)
1,300
1,049
1,346
1,334
680/690/675
637/647/632
336/346/331
319/329/314
(51.2)
(41.3)
(52.9)
(52.5)
With driver
(26.7)/(27.2)/(26.6)
(25.1)/(25.5)/(24.9)
(13.2)/(13.6)/(13.0)
(12.6)/(12.9)/(12.4)
■ 3 and 5Door (for T-GDI)
Vehicle
H3
W3
H1
H2
W1
W2
condition
FOG ONLY
FOG ONLY
Without
689/699/684
646/656/641
308/318/303
driver
(27.1)/(27.5)/(26.9)
(25.4)/(25.8)/(25.2)
(12.1)/(12.5)/(11.9)
1,300
1,049
1,308
680/690/675
637/647/632
299/309/294
(51.2)
(41.3)
(51.5)
With driver
(26.7)/(27.2)/(26.6)
(25.1)/(25.5)/(24.9)
(11.8)/(12.2)/(11.6)
■ 3,5 Door and Wagon (for Sports Pack)
Vehicle
H1
H2
H3
W1
W2
W3
condition
Without
689/699/684
646/656/641
305/315/300
driver
(27.1)/(27.5)/(26.9)
(25.4)/(25.8)/(25.2)
(12.0)/(12.4)/(11.8)
1,300
1,049
1,332
680/690/675
637/647/632
296/306/291
(51.2)
(41.3)
(52.4)
With driver
(26.7)/(27.2)/(26.6)
(25.1)/(25.5)/(24.9)
(11.7)/(12.0)/(11.5)
7 88
JD PE eng 7.QXP
03.01.2017
17:23 Page 89
Maintenance
■ Based on 10m screen
OMD051054L
Head lamp low beam (driver’s side)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.
7 89
JD PE eng 7.QXP
03.01.2017
17:23 Page 90
Maintenance
■ Based on 10m screen
OXM073102
Head lamp low beam (LHD)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.
7 90
JD PE eng 7.QXP
03.01.2017
17:23 Page 91
Maintenance
OXM073103
Head lamp low beam (RHD)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.
7 91
JD PE eng 7.QXP
03.01.2017
17:23 Page 92
Maintenance
■ Based on 10m screen
OGDE071056-JD
Front fog light
1. Turn the front fog lamp on without the driver aboard.
2. The cut-off line should be projected in the allowable range (shaded region).
7 92
JD PE eng 7.QXP
03.01.2017
17:23 Page 93
Maintenance
■ 5 Door
■ 3 Door
• Type A
■ Wagon
• Type B
OJD072029
Side repeater light bulb replace-
ment
If the light bulb does not operate, we rec-
ommend that the system be checked by
an authorized Kia dealer.
OJD075030/OJD075063/OJD073072/OJD073072
Rear combination light bulb replacement
(1) Rear turn signal light
(5) Rear fog light (for 5 Door), Rear fog
(2) Stop/tail light
light (Driver’s side) or back-up light
(3) Back-up light
(Passenger’s side), (for wagon)
(for 3 Door and 5 Door)
(6) Rear fog light (for 3 Door)
(4) Tail light or stop/tail light
(7) Stop light (for 3 Door)
(for LED type)
(8) Tail light (for 3 Door)
7 93
JD PE eng 7.QXP
03.01.2017
17:23 Page 94
Maintenance
■ 5 Door
Stop/tail light
5. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
Turn signal light
OJD072057
7. Insert a new bulb by inserting it into
the socket and rotating it until it locks
■ Wagon
Stop/tail light
into place.
OJD072045
8. Install the socket in the assembly by
❈ The actual rear combination lamp shape in
aligning the tabs on the socket with the
the vehicle may differ from illustration.
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
Outside light
9. Reinstall the light assembly to the
Rear turn signal light and stop/tail light
Turn signal light
body of the vehicle.
1. Turn off the engine.
2. Open the tailgate.
OJD072064
■ 3 Door
3. Loosen the light assembly retaining
screws with a cross-tip screwdriver.
4. Remove the rear combination light
Stop or Stop/tail light
assembly from the body of the vehicle.
Turn signal light
OJD073073
7 94
JD PE eng 7.QXP
03.01.2017
17:23 Page 95
Maintenance
Stop and tail light or tail light (LED type)
If the light does not operate, we recom-
mend that the system be checked by an
authorized Kia dealer.
OJD072047
OJD072048
Inside light (5 Door and Wagon)
❈ These below steps (4~6) only for the 5 Door
1. Turn off the engine.
vehicle.
2. Open the tailgate.
4. Loosen the retaining nuts.
3. Remove the service cover using a flat-
blade screwdriver.
5. Disconnect the power connector.
6. Remove the rear combination light
assembly from the body of the vehicle.
7 95
JD PE eng 7.QXP
03.01.2017
17:23 Page 96
Maintenance
■ 5 Door
Tail light or tail and stop light (Bulb type)
Back-up light and rear fog light
Stop light
7. Remove the socket from the assembly
(5 Door and Wagon) (if equipped)
by turning the socket counterclockwise
7. Remove the socket from the assembly
until the tabs on the socket align with
by turning the socket counterclockwise
the slots on the assembly.
until the tabs on the socket align with
Rear fog light
8. Remove the bulb from the socket by
the slots on the assembly.
pressing it in and rotating it counter-
8. Pull the bulb out of the socket.
Back up light
clockwise until the tabs on the bulb
9. Insert a new bulb into the socket.
align with the slots in the socket. Pull
10. Install the socket into the assembly
the bulb out of the socket.
by aligning the tabs on the socket
OJD072058
9. Insert a new bulb by inserting it into
with the slots on the assembly and
■ Wagon
the socket and rotating it until it locks
turning the socket clockwise.
into place.
11. Reinstall the light assembly to the
10. Install the socket in the assembly by
body of the vehicle
aligning the tabs on the socket with
the slots in the assembly. Push the
❈ Rear fog light is located only on the
socket into the assembly and turn the
driver’s side. (for wagon)
Tail light
socket clockwise.
11. Install the service cover by putting it
into the service hole.
Rear fog/Backup light
OJD072065
❈ Rear fog light is located only on the driver’s
side (for wagon)
7 96
JD PE eng 7.QXP
03.01.2017
17:23 Page 97
Maintenance
4. Remove the bulb-socket from the
housing by turning the socket counter
clockwise until the tabs on the socket
align with the slots on the housing.
OJD075071
OJD073075
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector.
7. Reinstall the rear under cover.
OJD073074
✽ NOTICE
Rear fog light is only on the driver’s side
Rear fog light (if equipped)
(5 door, if equipped).
1. Remove the under cover by rotating
the screws.
2. Reach your hand into the back of the
rear bumper.
3. Disconnect the power connector.
7 97
JD PE eng 7.QXP
03.01.2017
17:24 Page 98
Maintenance
Tail light or stop and tail light (LED type)
If the light does not operate, we recom-
mend that the system be checked by an
authorized Kia dealer.
OJD072037
OGD071046
High mounted stop light bulb
License plate light bulb replace-
replacement
ment
If the light does not operate, we recom-
1. Turn off the engine.
mend that the system be checked by an
2. Remove the bulb assembly by press-
authorized Kia dealer.
ing the tabs.
3. Remove the socket by turning it coun-
terclockwise.
4. Remove the bulb by pulling it straight
out.
5. Install a new bulb.
6. Reinstall the bulb assembly securely
with the retaining screws.
7 98
JD PE eng 7.QXP
03.01.2017
17:24 Page 99
Maintenance
■ Map lamp
■ Luggage room lamp
Interior light bulb replacement
Map lamp, vanity mirror lamp,
room lamp, luggage room lamp
and glove box lamp
1. Using a flat-blade screwdriver, gently
pry the lens from the interior light
housing.
2. Remove the bulb by pulling it straight
out.
■ Vanity mirror lamp
■ Room lamp
WARNING
- Type A
Prior to working on the interior
lights, ensure that the light is off to
avoid burning your fingers or
receiving an electric shock.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior
light housing notches and snap the
lens into place.
■ Glove box lamp
- Type B
CAUTION
Be careful not to dirt or damage
lens, lens tab, and plastic housings.
OGD071039/OTD079035/OJD072043/OJD072038/OGDE071057/OGD071038
7 99
JD PE eng 7.QXP
03.01.2017
17:24 Page 100
Maintenance
APPEARANCE CARE
Exterior care
High-pressure washing
CAUTION
When using the High Pressure car wash
Exterior general caution
•
Do not use strong soap, chemical
system for cleaning the exterior of your
It is very important to follow the label
detergents or hot water, and do
vehicle, be aware that without following
directions when using any chemical clean-
not wash the vehicle in direct
the proper precautions, it may damage
er or polish. Read all warning and caution
sunlight or when the body of the
your car.
statements that appear on the label.
vehicle is warm.
•
Never let the high pressure car wash
•
Be careful when washing the side
nozzle come too close to the windows,
Finish maintenance
windows of your vehicle.
soft materials, light system (headlights,
Washing
Especially, with high-pressure
taillights and such), camera, sensors,
To help protect your vehicle’s finish from
water, water may leak through the
bumpers, rubber (including tires), and
rust and deterioration, wash it thoroughly
windows and wet the interior.
also the underside of the vehicle.
and frequently at least once a month with
•
To prevent damage to the plastic
•
The high pressure could damage
lukewarm or cold water.
parts and lamps, do not clean
these parts especially if injected from a
If you use your vehicle for off-road driv-
with chemical solvents or strong
short distance.
ing, you should wash it after each off-
detergents.
Never clean a specific point on the
road trip. Pay special attention to the
vehicle for a prolonged time. Applying
removal of any accumulation of salt, dirt,
the high pressure car wash nozzle for
mud, and other foreign materials. Ensure
WARNING - Wet brakes
a prolonged time it could damage and
drain holes in the lower edges of the
harm the vehicle.
After washing the vehicle, test the
doors and rocker panels are kept clean.
brakes while driving slowly to see if
•
Even while the high pressure car wash
Insects, tar, tree sap, bird droppings,
they have been affected by water. If
nozzle is applied from a distance for a
industrial pollution and similar deposits
braking performance is impaired,
limited time only, always bear in mind
can damage your vehicle’s finish if not
dry the brakes by applying them
that a direct stream would greatly
removed immediately.
lightly while maintaining a slow for-
affect the surface of the vehicle.
Even prompt washing with plain water may
ward speed.
•
Always use high pressure car washes
not completely remove all these deposits.
which supply jet spray nozzle system,
A mild soap, safe for use on painted sur-
not direct stream nozzle system
faces, may be used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water. Do
not allow soap to dry on the finish.
7 100
JD PE eng 7.QXP
03.01.2017
17:24 Page 101
Maintenance
Waxing
Finish damage repair
Wax the vehicle when water will no
Deep scratches or stone chips in the
longer bead on the paint.
painted surface must be repaired
Always wash and dry the vehicle before
promptly. Exposed metal will quickly rust
waxing. Use a good quality liquid or
and may develop into a major repair
paste wax, and follow the manufacturer’s
expense.
instructions. Wax all metal trim to protect
it and to maintain its luster.
✽ NOTICE
Removing oil, tar, and similar materials
If your vehicle is damaged and requires
with a spot remover will usually strip the
any metal repair or replacement, be sure
wax from the finish. Be sure to re-wax
the body shop applies anti-corrosion
these areas even if the rest of the vehicle
materials to the parts repaired or
OJB037800
does not yet need waxing.
replaced.
CAUTION
CAUTION
•
Water washing in the engine com-
• Wiping dust or dirt off the body
partment including high pressure
with a dry cloth will scratch the
water washing may cause the fail-
finish.
ure of electrical circuits located in
• Do not use steel wool, abrasive
the engine compartment.
cleaners, or strong detergents
•
Never allow water or other liquids
containing highly alkaline or
to come in contact with electri-
caustic agents on chrome-plated
cal/electronic components and
or anodized aluminum parts. This
air duct inside the vehicle as this
may result in damage to the pro-
may damage them.
tective coating and cause discol-
oration or paint deterioration.
7 101
JD PE eng 7.QXP
03.01.2017
17:24 Page 102
Maintenance
Bright-metal maintenance
Underbody maintenance
•
To remove road tar and insects, use a
Corrosive materials used for ice and
WARNING
tar remover, not a scraper or other
snow removal and dust control may col-
After washing the vehicle, test the
sharp object.
lect on the underbody. If these materials
brakes while driving slowly to see if
•
To protect the surfaces of bright-metal
are not removed, accelerated rusting can
they have been affected by water. If
parts from corrosion, apply a coating of
occur on underbody parts such as the
braking performance is impaired,
wax or chrome preservative and rub to
fuel lines, frame, floor pan and exhaust
dry the brakes by applying them
a high luster.
system, even though they have been
lightly while maintaining a slow for-
treated with rust protection.
ward speed.
•
During winter weather or in coastal
areas, cover the bright metal parts with
Thoroughly flush the vehicle underbody
a heavier coating of wax or preserva-
and wheel openings with lukewarm or
tive. If necessary, coat the parts with
cold water once a month, after off-road
non-corrosive petroleum jelly or other
driving and at the end of each winter. Pay
protective compound.
special attention to these areas because
it is difficult to see all the mud and dirt. It
will do more harm than good to wet down
the road grime without removing it. The
lower edges of doors, rocker panels, and
frame members have drain holes that
should not be allowed to clog with dirt;
trapped water in these areas can cause
rusting.
7 102
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст