Geely Diagnosis Flow. Manual part — 43
Geely Diagnosis Flow. Manual part - 43
169
No.127 Weak with poor performance while accelerating
General malfunction part:1. fuel containing water; 2. intake pressure sensor and throttle valve
position sensor;3. spark plug;4. ignition coil; 5. throttle valve body and idling speed bypass air
duct; 6. intake duct;7、idling speed regulator; 8 oil injector; 9. ignition timing; 10. exhaust pipe.
General diagnosis flowchart:
Serial No.
Operation steps
Results
Follow-ups
Yes Repair
1
Check there are malfunctions such as clutch skidding, low tire
pressure, braking dragging, incorrect tire dimension, incorrect
positioning of four wheels, etc.
No Next
step
Yes
Repair air intake
system
2
Check air filter is blocked.
No Next
step
Yes Next
step
3
Connect fuel pressure gauge (access point is front end of oil sucker
of fuel distribution pipe assembly), and start the engine, and check
fuel pressure is around 350kPa during accelerating.
No
Repair oil supply
system
Yes Next
step
4
Take out line of one cylinder, and connect spark plug, making spark
plug electrode about 5mm away from engine body. Startup the
engine and check strength of high pressure spark is normal.
No Repair
ignition
system
Yes Next
step
5
Check spark plug of each cylinder, and observe its type and
clearance conform to the specifications.
No
Adjust or replace
Yes
Clean concerned parts
6
Remove idling speed regulator, and check throttle valve body, idling
speed regulator and idling speed bypass air duct are with carbon
deposit.
No Next
step
Yes Next
step
7
Check intake pressure sensor, throttle valve position sensor and its
lines are normal.
No
Repair lines or replace
sensor
Yes
Replace malfunction
8
Remove oil injector, and check it is leaking or blocked with special
cleaning and analysis instrument.
No Next
step
Yes Replace
fuel
9
Check fuel condition and observe malfunction is caused just after
refueling.
No Next
step
Yes Next
step
10
Check ignition sequence and ignition timing of the engine conform to
the specifications.
No Repair
ignition
timing
Yes Next
step
11
Check exhaust pipe is smoothly exhausted.
No
Repair or replace
exhaust pipe
Yes
Diagnosis help
12
Connect commutator of electric injection system, and open ignition
switch, and check power supply of 12#, 13#, 44#, 45#, ,63# pins
are normal; check bonding of 3#, 51#, 53#, 61#, 80# pins are
normal.
No
Repair corresponding
lines
170
No.128 Malfunction code with EOBD system
NO Malfunction
code
Description
Malfunction
level
1
P0030
Open-circuit of heating control circuit of upstream oxygen sensor
3
2
P0031
Short-circuit to earth of heating control circuit of upstream oxygen sensor
3
3 P0032
Short-circuit to power source of heating control circuit of upstream oxygen
sensor
3
4
P0036
Open-circuit of heating control circuit of downstream oxygen sensor
3
5
P0037
Short-circuit to earth of heating control circuit for downstream oxygen sensor
3
6 P0038
Short-circuit to power source of heating control circuit for downstream oxygen
sensor
3
7 P0053
Unreasonable heating internal resistance, upstream oxygen sensor
3
8
P0054
Unreasonable heating internal resistance, downstream oxygen sensor
3
9
P0105
Unchanged signal (icing) of intake pressure sensor
3
10
P0106
Intake pressure sensor unreasonable
3
11
P0107
Intake pressure sensor short circuit to earth
3
12
P0108
Intake pressure sensor short circuit to power source
3
13
P0112
Too low signal voltage of intake temperature sensor
3
14
P0113
Too high signal voltage of intake temperature sensor
3
15
P0116
Unreasonable temperature signal of engine coolant
3
16
P0117
Too low circuit voltage of temperature sensor of engine coolant
3
17
P0118
Too high circuit voltage of temperature sensor of engine coolant
3
18
P0122
Circuit voltage exceeding minimum value, throttle position sensor
3
19
P0123
Circuit voltage exceeding maximum value, throttle position sensor
3
20
P0130
Unreasonable signal upstream oxygen sensor
3
21
P0132
Circuit voltage too high, upstream oxygen sensor signal
3
22
P0133
Upstream oxygen sensor aging (signal slows down)
3
171
23
P0134
Circuit signal malfunction, upstream oxygen sensor
3
24
P0136
Unreasonable signal of downstream oxygen sensor
3
25
P0138
Circuit voltage too high, downstream oxygen sensor signal
3
26
P0140
Circuit signal malfunction, downstream oxygen sensor
3
27 P0170
Unreasonable self-learning of closed-loop control of air fuel ratio for off-line
test
7
28
P0171
Over-thin of self-learning of closed-loop control of air fuel ratio for off-line test
7
29
P0172
Lower cable inspection air/fuel ratio closed circuit self-adaptation too thick
7
30
P0201
Open circuit of 1st cylinder fuel injector controlling circuit
3
31
P0202
Open circuit of 2nd cylinder fuel injector controlling circuit
3
32
P0203
3rd cylinder fuel injector controlling circuit open circuit
3
33
P0204
Open circuit of 4th cylinder fuel injector controlling l circuit
3
34
P0261
Short circuit to earth of 1st cylinder fuel injector controlling circuit
3
35
P0262
Short circuit to power supply of 1st cylinder fuel injector controlling circuit
3
36
P0264
Short circuit to earth of 2nd cylinder fuel injector controlling circuit
3
37
P0265
Short circuit to power supply of 2nd cylinder fuel injector controlling t circuit
3
38
P0267
Short circuit to earth of 3rd cylinder fuel injector controlling circuit
3
39
P0268
Short circuit to power supply of 3rd cylinder fuel injector controlling circuit
3
40
P0270
Short circuit to earth of 4th cylinder fuel injector controlling circuit
3
41
P0271
Short circuit to power supply of 4th cylinder fuel injector controlling circuit
3
42
P0300
Several cylinders misfire
2
43
P0301
1st cylinder misfire
2
172
44
P0302
2nd cylinder misfire
2
45
P0303
3rd cylinder misfire
2
46
P0304
4th cylinder misfire
2
47
P0318
Damaged circuit inspection accelerating sensor signal failure
3
48
P0321
Crankshaft signal error
3
49
P0322
No engine speed sensor pulse signal (open or short circuit)
4
50
P0324
Knock signal processing chip and other circuit malfunction
6
51
P0327
Knock sensor signal circuit voltage lower than normal value
3
52
P0328
Knock sensor signal circuit voltage over normal value
3
53
P0340
Improper phase sensor mounting position
3
54
P0341
Poor phase sensor conduction
3
55
P0342
Phase sensor short circuit with earth
3
56
P0343
Phase sensor short circuit with power supply
3
57
P0420
3 way catalytic converter ageing (emission over standard level)
3
58
P0444
Canister valve controlling circuit open circuit
3
59
P0458
Canister valve controlling circuit voltage lower than normal value
3
60
P0459
Canister valve controlling circuit voltage over normal value
3
61
P0480
Cooling fan relay controlling circuit open circuit (low speed)
5
62
P0481
Cooling fan relay controlling circuit open circuit (high speed)
5
63
P0501
Vehicle speed sensor signal unreasonable
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст