Geely FC. Manual part — 27
Geely FC. Manual part - 27
Rear suspension - Rear stabilizer bar
Rear stabilizer bar
Overhaul
1. Remove rear stabilizer bar assembly.
Remove 2 bolts, nuts and stabilizer bar.
2. Install rear stabilizer bar assembly.
Install 2 bolts, nuts and stabilizer bar.
Torque:
Hint:
install the tag on balance bar toward rear right
side of vehicle.
Front
Tag
105
Rear suspension - Rear shaft assembly
Rear shaft assembly
Overhaul
1. Remove rear wheels.
2. Disassemble rear left brake caliper assembly
(see Page 144).
3. Disassemble rear right brake caliper assembly
(see Page 144).
4. Disassemble rear wheel speed sensor wire harness
(a) Uncouple sensor joint.
(b) Remove 2 bolts and disassemble wire harness retaining
clip.
5. Remove rear left/right brake assembly [64000137/
64000139].
(See Page 144)
6. Remove rear stabilizer bar assembly (see Page 105).
7. Disassemble rear left/right strut assembly
(see Page 102).
8. Remove rear shaft assembly [64000120].
(a) Support rear shaft assembly with a jack.
(b) Remove 2 bolts, gasket and rear shaft.
Special
tool
106
Rear suspension - Rear shaft assembly
9. Remove left side rear shaft gum cover assembly.
(a) Inscribe 2 matching marks at the dent part of gum cover
and axle beam.
(b) Bend two parts of bush frame with chisel and hammer.
Hint: bend bush frame until it reaches the hook of spe-
cial tool.
(c) Remove gum cover from axle beam with special tool.
Hint: if axle beam is damaged, please spray paint.
10.
Remove right side rear shaft gum cover assembly.
Hint: the removal procedures of right side are the
same as that of left side.
11.
Remove left side rear shaft gum cover assembly.
(a) Align the dent on new bush with the matching mark
previously making on axle beam, and then temporarily
encase gum cover into axle beam.
(b) Encase gum cover into axle beam with special tool.
Notes:
The hook of special tool should be deeply and
actually inserted into gum cover.
Do not damage the rubber port of gum cover.
O
Do not deform gum cover frame.
12.
Install right side rear shaft gum cover assembly.
Hint: the installation procedures of right side are the
same as that of left side.
13.
Temporarily lock up rear shaft assembly
[64000120].
(a) Support rear shaft with a jack.
(b) Install rear shaft, 2 bolts and gasket, and then tempo-
rarily lock up 2 nuts.
Installation remark
Dent
Dent
Special
tool
Bending part
Special tool
Rubber
port
107
14.
Temporarily lock up rear left strut assembly.
(a) Install rear left strut and gasket, and temporarily lock
up nuts.
(b) Perform to another side in the same way.
15.
Install rear stabilizer bar assembly (see Page 105).
16.
Install rear left/right brake assembly [64000137/64000139] (see Page 144).
17.
Install rear wheel speed sensor wire harness.
Install wire harness and parking brake cable with 2 bolts and retaining clips.
Torque: (A) 5.4 N.m
(B) 5.0 N.m
Rear suspension - Rear shaft assembly
108
18.
Install rear left brake caliper assembly
(see Page 144).
19.
Install rear right brake caliper assembly
(see Page 144).
20.
Align suspension.
(a) Lay down vehicle from the lift after installing rear wheels.
Torque:
(b) Align suspension components by means of lifting ve-
hicle with a jack several times.
21.
Completely lock up rear shaft assembly
[64000120].
(a) Completely tighten bolts and pull on open pin.
Torque:
m
(b) Perform to another side in the same way.
22.
Completely lock up rear left strut assembly.
(a) Completely tighten bolts.
Torque:
m
(b) Perform to another side in the same way.
23.
Check rear wheel alignment (see Page 101).
24.
Check ABS sensor signal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст