Geely FC. Manual part — 15
Geely FC. Manual part - 15
Engine mechanism - Camshaft
(i) Temporarily tighten fixed bolts.
(j) Check forward mark and figure, and tighten bolts as
sequences shown in the diagram.
Torque:
±0.78N.m
(k) Install camshaft front bearing cover.
Torque: 23 ±1.38N.m
(l) Fix camshaft with variable wrench and then tighten the
fixed bolts of exhaust camshaft timing sprocket.
Torque: 54 ±10.8N.m
Note: be careful not to damage valve lifter.
(m)Check the alignment marks on timing chain and cam-
shaft timing sprocket, and then align the groove of damp-
ing pulley with the timing mark on timing chain hood as
shown in the diagram.
Fixing
Tightening
57
Mark
Mark
Mark
Timing chain hood
Groove
Engine mechanism - Camshaft
(n) Install chain tensioner components.
(1) Check o-ring is clean, and buckle on the hook as
shown in the diagram.
(2) Coat engine oil on the chain tensioner, and then
install it.
Torque: 9 ±1.8N.m
Note: when installing the chain temsioner,
buckle on the hook again if plunger has
ejected.
(3) Turn crankshaft counterclockwise to separate the
hook from lock pin on the plunger.
(4) Turn crankshaft clockwise, and check the sliding
parts are blocked by plunger.
Hint: if the plunger does not eject, press the ten-
sion rail toward chain tensioner with
screwdriver or fingers to separate the hook
from lock pin and make the plunger eject.
Pushing into
Turning
Plunger
Pushing into
58
Lifting
Hook
Pressing
in
Pin
Pin
Hook
Sepa-
rate
Engine mechanism - Camshaft
14.
Adjust valve clearance.
15.
Install cylinder head cover components.
(a) Install gasket to cylinder head cover.
(b) Eliminate all old sealant (FIPG) materials.
(c) Coat sealant on position shown in the diagram.
Sealant: silicon rubber flange sealant 1596 (Kesaixin
1596).
Notes:
Eliminate all oil on contact surface.
After coating sealant, finish installation of cylinder
head cover within 3 minutes.
After installing, do not refill engine oil within 2
minutes.
(d) Install cylinder head cover and harness bracket with 9
bolts, 2 oil seal washers and 2 nuts.
Evenly tighten bolts and nuts at several times.
Torque: nut: 29 ±5.8N.m
Bolt: 69 ±13.8N.m
16.
Install drive belt tensioner device.
Torque: nut: 29 ±5.8N.m
Bolt: 69 ±13.8N.m
17.
Install right engine mounting assembly.
Torque: 52N.m
18.
Check there is oil leakage.
59
Engine mechanism - Crankshaft front oil seal assembly
Replacement
1. Remove engine right bottom shield.
2. Remove drive belt.
Slowly turn drive belt tensioner clockwise to loosen it. Then
remove drive belt and put back drive belt tensioner slowly and
gently.
3. Remove right engine mounting assembly.
(a) Remove PS oil pump reservoir and put it aside.
(b) Place wooden block between jack and engine, properly
place the jack, and then remove right engine mounting
assembly.
4. remove damping pulley.
(a) Remove pulley bolts with special tool.
(b) Remove damping pulley with special tool.
Special
tool
Special
tool
60
Crankshaft front oil seal assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст