Geely FC. Manual part — 72
Geely FC. Manual part - 72
Light--Light System
(a) Inspect the conduction of B pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth, when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
7. Inspect the C door pillar control switch assembly [67000076]
(a) Inspect the conduction of C pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth,when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
8. Trunk light switch assemble [67000073]
(a) Inspect the conduction of Trunk light switch
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
9. Front fog light relay [67000071]
(a) Inspect the conduction of front fog light relay
(1) Inspect the conduction among terminals
Standards:
Avometer terminals
regular situations
1-2
conduction
3-5
not conduction
10. Inspect rear fog light switch of instrument block
left switch units [67010003].
(a) Inspect battery’s positive wire connects to terminal 1,nega-
tive connects to terminals 7.
(b) Connect a 3.4W test bulb from battery’s positive wire to
terminal 3.
(c) Inspect lighting switch, indicator light of assembled instru-
ments and test bulb should light. If it does not accord with
regularizations, replace the switch.
11. Inspect door light assembly [67000107]
Inspect the conduction among terminals.
If the conduction does not accord with regularizations, replace
the switch.
(2) Supply battery voltage(10-14V) to terminal1 and terminal2, then inspect the conduction between
terminal 3 and terminal 5.
Standard: conduction
1
285
Light--Front fog light joint
Front combination light (LH)
Subassembly
Left front combination
light units
Front combination
light bulb
Front combination
light bulb
Front combination light
bulb joint
Ultrasonic sensor joint
Radiator cover
assembly
Front fog light
joint
Light
seat cap
Bulb joint
Bulb
Bulb
Front fog light joint
Front bumper
286
Light--Front fog light joint
Change
Notes:
z
Assemble according to the opposite of disassemble. Instructions comes when necessary.
z
The replace procedure are the same on the left and right side.
z
Referring to the drawing of front combination light on page 286.
1. Disassemble Radiator cover assembly (reference to page 380)
2. Disassemble left front tyre lining (reference to page 380)
3. Disassemble right front tyre lining (reference to page 380)
4. Disassemble front bumper (reference to page 380)
5. Disassemble left front combination light assembly [67000102]
(a) Disassemble three bolts
(b) Disassemble four joints
(c) Pull combination light ahead
(d) Disassemble two light seat cap and four bulbs.
Adjustments
1. Adjust front combination light focus only
(a) Parking car should accord to the following situations:
z
Front combination light around does not be distorted or damaged.
z
Park the car on flat road.
z
Tyre pressure limits to the regular number value
z
The driver is on driving seat and the car is ready to go(gasoline tank in full)
z
The car weaves fore-and-aft for many times.
(b) Inspect front combination light focus
(1) Prepare for thicker white paper
(2) Arise the paper plumb at the distance of 300cm from headlight.
(3) Make sure centerline of the car makes 90 degree angle with paper’s surface as following drawing.
(4) Draw a level line (H line) on the paper which headlight can irradiate.
(5) Draw a plumb line (V line) on the paper to across centerline of the car.
(6) Draw two level lines (V RH and V LH) in the area where two side lights can irradiate.
(7) Draw a level line(connect the middle signal of two low beam headlight) to the area where headlight
can irradiates.
Clues on: H RH and H LH lines are 0.57 lower than level line(H line)of light.
(8) Start the engine.
(9) Turn the front assembled switch to ON.
Pin
287
Light--Front fog light joint
Clues on:
z
Adjust the focus between lights of RH and LH as the drawing.
z
The value of low beam focal length is reference value for it is impossible to adjust at
level direction.
(c) Adjust vertical direction
Use the adjustable bolt A to make the headlight focus limits
to the regular.
(d) Adjust level direction
Use the adjustable bolt B to make the headlight focus limits
to the regular.
(10) Inspect front combination light whether it irradiates on the area as drawing.
(11) If not, adjust light on vertical line or level line.
Adjusting bolt “B”
Adjusting bolt “A”
288
1 2 0 9 . 0
939.8
Numbers for approach sequence
Distant
light
Low
beam
light
wire
wire
wire
wire
wire
wire
H RH and
H LH wire
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст