Geely FC. Manual part — 71
Geely FC. Manual part - 71
Light--Light System
All lights do not light
When driver cap side door opens,
the light does not light
When right front door opens, the
light does not light
When right rear door opens, the
light does not light
When left rear door opens, the light
does not light
Only one light can light
After all doors are closed, illuminat-
ing lamp will not flame out gradually.
After all doors closed, the head lamp
does not light in 15 seconds, when
turn ignition switch to ACC or ON.
Driver side light or passenger cap
side light do not light
When Driver side door opens,
driver side light does not light
When Passenger side door opens,
passenger side light does not light
1. (room light) fuse
1. driver cap side door control switch
2. wiring harness
3. bulb
1. right front door control switch
2. wiring harness
3. bulb
1. right rear door control switch
2. wiring harness
3. bulb
1. left rear door control switch
2. wiring harness
3. bulb
1. bulb
1. Door-control switch
2. Wire harness
1. ignition switch
2. fuse
3. light relay
4. wiring harness
1. (door) fuse
2. (meter) fuse
3. light relay
4. driver side door control switch
5. bulb
6. wiring harness
1. driver side door control switch
2. wiring harness
3. bulb
1. passenger side door control switch
2. wiring harness
3. bulb
4. Room lights system
Inspect the car
1. inspect turning flasher wiring
(a) Disassemble joint from turning flasher and inspect wiring
harness side joint as following table.
phenomena
Possible parts
Reference pages
281
(b) Inspect function of rear fog light.
(1) Turn the ignition switch to ON.
(2) Inspect rear fog light’s situation when every switch works, just as following table.
Light--Light System
(b) Connect joint to directional switch and inspect from wiring harness’s side joint as following table:
Avometer terminals
2-earth
2-earth
3-earth
3-earth
5-earth
6-earth
8-earth
condition
warning light switch OFF
→ ON
turn light switch (right) OFF
→ ON
warning light switch OFF
→ ON
turn light (left) switch OFF
→ ON
turn light(left) switch OFF
→ ON
turn light(right) switch OFF
→ ON
warning light switch OFF
→ ON
r
egular situation
0V
→ 0 ⇔ 9Vevery min 60 to 120 times
0V
→ 0 ⇔ every min 60 to 120 times
0V
→ 0 ⇔ 9Vevery min 60 to 120 times
0V
→ 0 ⇔ 9Vevery min 60 to 120 times
over 9V
→ 0V
over 9V
→ 0V
over 9V
→ 0V
2. Inspect rear fog light switch
(a) inspect rear fog light wiring
(1) Disassemble the joint from switch sides and inspect the
joint from wiring harness as following table.
Avometer terminals
1-earth
2-earth
3-earth
5-earth
6-earth
7-earth
condition
normal
light control switch OFF
→ ON
normal
light control switch OFF
→ ON
front fog light switch OFF
→ ON
normal
regular situation
conduct
ion
0V
→ 10-14V
10-14V
not conduct
ion
→ conduct
ion
not conduct
ion
→ conduct
ion
conduct
ion
Situation
Light switch OFF
→ ON, front fog light switch OFF
Light switch OFF
→ ON, front fog light switch ON, rear fog light switch ON
rear fog light working situations
rear fog light does not light
rear fog light lights
3. Inspect lighting system function
Clues on:
key aperture lamp and room light.
Avometer terminals
7-earth
1-earth
1-earth
4-earth
condition
normal
turn light switch ON
turn light switch ON
normal
regular situations
conduct
ion
battery voltage
no voltage
battery voltage
Wiring
harness side
282
Light--Light System
(a) Turn the ignition switch to OFF and open all doors, then lock driver cap side door.
(b) Unlock the drive’s side door and open any door, then inspect whether room light lights. Close the door
and inspect whether room light lights off in 15 seconds.
(c) Turn ignition switch to ON, then open any door to inspect whether room light lights off immediately.
(d) Turn ignition switch to OFF.
(e) Open or close any door to light room light. Turn ignition switch to ON before room light turns off(about
15seconds) to inspect whether room light turns off immediately.
(f) Turn ignition switch to OFF.
(g) Open or close any door to light room light. Lock driver cap side door before room light turns off(about
15seconds) to inspect whether room light turns off immediately.
Inspect
1. Front combination headlight dimmer switch
assembly
(a) Inspect the conduction of light control switch
(1) Inspect switch on every positions, the conduction among
terminals as following table.
Switch positions
Avometer terminals
regular situations
OFF
-
not conduction
Position light
12-6
conduction
Lamp
12-6
conduction
Lamp
7-10
conduction
(b) Inspect conduction of front assembled dimmer switch
(1) Inspect switch on every parts, the conduction among terminals as following table.
Switch positions
Avometer terminals
regular situations
Flasher
11-10
conduction
Low beam light
9-10
conduction
Distant light
7-10
conduction
(c) Inspect the conduction of turning light switch
(1) Inspect switch on every positions, the conduction among terminals as following table.
Switch positions
Avometer terminals
regular situations
Turn right
4-5
conduction
neutral
-
not conduction
turn left
4-3
conduction
283
Light--Light System
Switch positions
Avometer terminals
regular situation
OFF
1-2
not conduction
ON
1-2
conduction
(d) Inspect conduction of front fog light switch
(1) Inspect switch on every positions, the conduction among terminals as following table.
Switch positions
Avometer terminals
regular situation
OFF
-
not conduction
DOOR
1-2
conduction
ON
2-bodywork earth
conduction
2. Interior rear top light assembly [67010006]
(a) Inspect the conduction of interior rear top light
(1) Inspect switch on every position, the conduction among
terminals as following table.
Standard:
3. Room front top light assembly [67010007] (equipped
with electric sunroof [67010009])
(a) Inspect the conduction of room front roof light
(1) Inspect the conduction between terminal 1 and terminal
2,when switch works.
Standard:
ON: conduction
OFF: not conduction
4. Room front top light assembly [67010005](do not
equipped with electric sunroof)
(a) Inspect the conduction of room front roof light
(1) Inspect the conduction between terminal 1 and terminal
2,when switch works.
Standard:
ON: conduction
OFF: not conduction
5. Trunk lighting assemble [67000106]
(a) Inspect the conduction among terminals.
Standard: conduction
6. Inspect the B door pillar control switch assembly
[67000075]
1
2
284
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст