Geely CK (2008). Manual part — 37
Geely CK (2008). Manual part - 37
145
Remove 2 boots from the brake cylinder support bracket.
7. Remove the brake cylinder guide boot
Remove the clip and boot with screwdriver.
8. Remove the bleeder screw
9. Remove the front brake piston
(1) Put a piece of soft cloth between the brake cylinder and piston.
(2) Blow the piston out from the brake cylinder with the compressed air
Notice: Be careful not to put your finger in front of the piston when blowing
the compressed air. Be careful of the splashed brake fluid
10. Remove the piston oil seal
Remove the oil seal from the brake cylinder with a screwdriver
11.Check the brake cylinder and piston
Check the cylinder wall and piston for rust and damage
12. Check the thickness of the brake pad
Measure the thickness with a ruler: Standard thickness: 10mm,
Minimum thickness: 1mm
13. Check the front brake alarm plate
Make sure the alarm plate has enough elasticity, and is not cracked
or worn. Clean all rust, dirt and foreign materials
14. Check disc thickness
Measure the disc thickness with micrometer:
Standard thickness: 11mm
Minimum thickness: 10mm
146
15. Remove the front disc
16. Installation is in the reverse order of the above-mentioned procedure
Notice:
(1) The maximum lateral runout of the disc surface should be no more than 0.05mm
(Measured 10mm from the brake disc outside edge)
(2) Be careful not to install the brake cylinder guide boot in the reverse direction
(3) Make sure the cylinder and the piston oil seal are clean before installing the
piston oil seal in the brake cylinder. Apply lithium soap base glycol grease to
the piston surface. Never rotate the piston into the brake cylinder by force.
(4) Install the brake caliper to tighten the bolt torque: 85~90 N.m
(5) Replace the noise insulator when replacing the worn brake pad. Make sure the
clip plate is in normal status. Otherwise, replace the floating clip plate
(6) Make sure the brake pad and disc surface are clean. Oil or grease is not attached.
(7) Install the brake hose. Uion thread torque: 16~20N.m
(8) Bleed the air in the brake system. Check the brake system for leakage.
(9) Install the front wheel. The tire nut torque: 95~115 N.m
simultaneously.
floating
147
Section 6 Rear Brake
Components
Repairing
1. Remove rear wheel
2. Drain the brake fluid
3. Remove the brake drum
(1) loose the parking brake handle
(2) Remove the cotter pin with a long nose pliers
(3) loose the spindle slot nut
Lower Return Spring
Oil Baf
fle Plate
Anchor Plate
Brake Bottom Plates
Left Cable Plate
Left T
orsion
Spring
Adjusting Pawl Shaft
Pin
Left Adjusting
Pawl
Left Adjusting
Plate
Brake Shoe I
Wheel Hub Bearing II
Rear Spindle Cap
Wheel Hub
Bearing I
Stop W
asher
Wheel Hub
Bolt
Rear Ring Gear
Rear Brake Drum
Rear Spindle Cover
Brake Shoe I
Shoe Guide
Friction Shoe
Boot
Cup
Piston
Wheel Cylinder
Spring
Piston
Boot
Cup
Parking Brake
Left Swing
Arm
Rear Brake
Auto
Adjusting Lever
Adjusting Lever Spring
Return Spring
148
(4) remove the brake drum
4. Measure brake drum inside diameter
Standard inside diameter: 180mm
Maximum inside diameter: 181mm
5. Separate the parking brake left swing arm. Loose the parking brake cable end joint
Separate the parking brake left swing arm. Remove the parking brake cable end joint with a screwdriver.
6. Remove the brake shoe I, brake shoe II
(1) using special tool, remove brake shoe positioning spring and pin
(2) remove brake shoe I and I after separating the return spring
7. Remove the rear brake automatic adjustment lever
Remove the brake adjustment lever spring and adjustment lever
8. Remove the return spring on the brake shoe
Remove the return spring from the brake shoe
Push
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст