Geely Emgrand X7. Manual part — 567
Geely Emgrand X7. Manual part - 567
NL11-2115b
1
2
3
4 5 6
7
8
9
14 15 16 17 18
10 11
12 13
IP52 雨刮洗涤器组合开关线束连接器
8
NL11-2112b
1
4
5
2
3
CA14 前雨刮器电机线束连接器
2
NL11-2116b
IP48 车身控制模块线束连接器2
1 2 3
4 5 6
7 8 9
10 11 12 13
13
Test terminal
Specified value
IP50(23)-IP52(8) Less
than
1
Ω
IP48(13)-CA14(3) Less
than
1
Ω
IP52wiper washer combination
switchharness connector
CA14frontwiper motor harness
connector
IP48body control module harness
connector2
2267
Confirm if the resistance conforms to standard value.
5
Repair the circuit fault point among the BCM wire harness connector terminal, the wiper
switch and the wiper motor.
(a) Repair fault points between BCM wire harness connector terminal and wiper switch, wiper
motor.
(b) Connect wiper switch wire harness connector IP52.
(c) Connect to wiper motor harness connector CA14,
(d) Connect to BCM harness connector IP50. IP48.
(e) Connect the battery negative cable.
(f) Turn the ignition switch to "ON" position.
(g) Operated wiper switch high speed (HIGH).
Confirm whether the voltage of the terminal No. 3 of the wiper motor wire harness connector
CA14 and the effective body grounding point is normal.
Confirm whether the wiper works normally.
Replace wiper motor, refer to11.5.8.10 replace wiper motor
Confirm the completion of repair.
8
The system is normal.
6
Replace the BCM
7 Replace
wiper
motor
Next
Yes
The system is normal.
No
Yes
Go to step 7
No
Yes
Go to step 6
No
2268
11.6.7.5 Wiper inoperation at low speed
Circuit diagram:
See 11.6.7.3 wiper does not work under any gear position.
Diagnostic steps:
1
Inspect the voltage of the terminal No. 3 of the wiper motor wire harness connector
CA14 and the effective body grounding point.
(a) Rotated ignition switch to "OFF"
position.
(b) Disconnect the wiper motor
harness connector CA14.
(c) Place wiper switch to high speed
gear (LOW) position.
(d) Turn ignition switch "ON"
position.
(e) Use multimeter to measure
voltage between wire harness
connector CA14 terminal No. 3
and vehicle body grounding.
Standard voltage: 11-14 V
Confirm if the voltage conforms to
standard value.
NL11-2105b
1
4
5
2
3
CA14 前雨刮器电机线束连接器
2
Inspect the wiper switch.
(a) Rotated ignition switch to "OFF"
position.
(b) Disconnect wiper switch harness
connector IP52.
(c) Operate wiper switch and use
multimeter to measure the
connection situation of switch.
NL11-2107b
1
2
3
4 5 6
7
8
9
14 15 16 17 18
10 11
12 13
IP52 雨刮洗涤器组合开关线束连接器
17
7
No
Go to step 7
Yes
CA14 frontwiper motor harness
connector
IP52wiper washer combination
switchharness connector
2269
Test terminal
Test conditions
Specified value
IP52(07)-IP52(17) Low
revolution speed gear
Less than 1 Ω
Confirm if the resistance conforms to standard value.
3
Replace wiper switch.
(a) Replace wiper switch, refer to11.5.8.9 wiper and washer switch replacement .
Confirm whether system work is normal or not
4
Replace wiper switch
(a) Rotated ignition switch to "OFF"
position.
(b) Disconnect the battery negative
cable.
(c)
Disconnect BCM harness
connector IP50, IP48.
(d) Disconnect wiper switch wire
harness connector IP52.
(e) Disconnect wiper motor harness
connector CA14.
NL11-2111b
1
2
3
4 5 6
7
8
9
14 15 16 17 18
10 11
12 13
IP52 雨刮洗涤器组合开关线束连接器
7
Yes
The system is normal.
No
Yes
Go to step 4
No
IP52wiper washer combination
switchharness connector
2270
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст