Geely Emgrand X7. Manual part — 568
Geely Emgrand X7. Manual part - 568
(f) Measure harness energy guide
between BCM harness connector
terminal and wiper switch. Wiper
motor by millimeter.
NL11-2117b
IP50 车身控制模块线束连接器4
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
2
NL11-2105b
1
4
5
2
3
CA14 前雨刮器电机线束连接器
NL11-2108b
IP47 车身控制模块线束连接器2
1 2 3
4 5 6
7 8 9
10 11 12 13
12
Test terminal
Specified value
IP50(2)-IP52(7) Less
than
1
Ω
IP50 body control module harness
connector4
CA14 front wiper motor harness
connector
IP47 body control module harness
connector2
2271
IP48(12)-CA14(2) Less
than
1
Ω
Confirm whether the resistance conforms to standard value.
5
Repair the wire harness fault point among the BCM wire harness connector terminal, the
wiper switch and the wiper motor.
(a) Repair wire harness fault points between BCM wire harness connector terminal and wiper
switch, wiper motor.
(b) Connect wiper switch wire harness connector IP52.
(c) Connect to BCM harness connector IP50, IP48.
(d) Connect to wiper harness connector CA14.
(e) Connect the battery negative cable.
(f) Turn on ignition switch to "ON" position.
(g) Operated wiper switch low speed (LOW).
(h) Voltage between wiper motor wire harness connector CA14 terminal No. 2 and vehicle body.
Standard voltage: 11-14 V
Confirm whether the voltage is normal.
(a) Replace
BCM.
Confirm whether the wiper works normally.
7 Replace
wiper
motor
Replace wiper motor, refer to11.5.8.10 Replace wiper motor
Confirm the completion of repair.
6
Replace the BCM
Next
Yes
The system is normal.
No
Yes
Go to step 7
No
Yes
Go to step 6
No
2272
8
The system is normal.
2273
11.6.7.6 Wiper inoperation at intermittent
Circuit diagram:
See 11.6.7.3 wiper does not work under any gear position.
Diagnostic steps:
1
Inspect the voltage of the terminal No. 2 of the wiper motor wire harness connector
CA14 and the effective body grounding point.
(a) Disconnect wiper motor harness
connector CA14.
(b) Place wiper switch to interval
(INT) position.
(c) Rotated ignition switch to "ON"
position.
(d) Use multimeter to measure
effective grounding voltage
between wire harness connector
CA14 terminal No. 2 and vehicle
body.
Standard voltage: 11-14 V
Confirm if the voltage conforms to
standard value.
NL11-2105b
1
4
5
2
3
CA14 前雨刮器电机线束连接器
2
Inspect the wiper switch.
(a) Rotated ignition switch to "OFF"
position.
(b) Disconnect wiper switch harness
connector IP52.
(c) Place wiper switch to interval
gear and use multimeter to
measure the connection situation
of switch.
NL11-2118b
1
2
3
4 5 6
7
8
9
14 15 16 17 18
10 11
12 13
IP52 雨刮洗涤器组合开关线束连接器
13
15
No
Go to step 7
Yes
CA14 frontWiper motor harness
connector
IP52wiper washer combination
switchharness connector
2274
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст