Geely Emgrand X7. Manual part — 97

B056

No key was stored
in the anti-theft
device

Anti-theft controller
has not matched
with any key, and
therefore no
transponder ID is
stored in it.

Learn the key again.

B057

No security code
has been set .

New or reset
anti-theft controller

Set the security code and match the
anti-theft controller again.

B059

No electric injector
controller request
was received

The anti-theft
controller didn’t
receive the
communication
request from the
electric injector
controller

1. Inspect the insertion of the

harness connector of the
anti-theft controller

2. Inspect the connection, open

circuit or poor contact of the
harness between the anti-theft
controller terminal 5 and the
ECM.

3. Replace the anti-theft controller

and inspect the above
mentioned faults. If no fault
occurred, the fault can be
deemed within the anti-theft
controller;

4. Replace the ECM and inspect

the above faults. If no fault
occurred, the problem can be
deemed as within the electric
injector.

B060

The current key is
not stored in the
anti-theft device

The transponder ID
is not stored in the
anti-theft controller

Use the scan tool to exert the “Key
Learning” function

B061

Key is unable to be
verified or the
communication is
disturbed.

Communication
between the
transponder and the
anti-theft controller
can not be
established or be
disturbed. The
communication
data are abnormal.
The electric injector
and transponder
have inconsistent
key.

1. Inspect whether the EAS Coil is

normal.

2. Inspect whether the transponder

is new or unmatched. If so,
match them again.

3. If the transponder is matched,

confirm the exchanging of the
transponder, or the exchanging
and resetting of the electric
injector.

Note: DTC (DTC code) is set based on the above-mentioned output sequence. However, at the
same time it only shows a maximum of 7 DTC.

Note: DTC code history is code recorded before shown by the scan tool. If a DTC code has no
historical features, it only shows the current status. If there are historical features, it can display
the status up to 20 ignition cycles.

387

2.5.7.5 Data Flow Table

Serial Number

Description

Data

1

Ignition Switch 0

N/OFF

2 Key

Detection

YES/NO

3 Ever

matched

YES/NO

4

The Current Key Position

Not Programmed/Programmed

5

Key Storage Position 1

Not Stored/Stored

6

Key Storage Position 2

Not Stored/Stored

7

Key Storage Position 3

Not Stored/Stored

8

Key Storage Position 4

Not Stored/Stored

9

Key Storage Position 5

Not Stored/Stored

10

Security Certification

Not Passed/Passed

11 Anti-theft

Verification

YES/NO

12

Vehicle Identification Number

Not Programmed/Programmed

13 Password

Settings

YES/NO

14 Password

Lock

YES/NO

15 Entering

The

Password

YES/NO

16

Remaining Numbers Of Times
Entering The Password

10

2.5.7.6 Fault Symptom Table

Symptoms

Suspected Parts

Refer to Page

Engine Anti-theft Indicator
Always On

Instrument Refer

to

11.6.7.1 Replacement

of Combination Instrument
Assembly.

1. Key

2. Anti-theft

Coil

3. Anti-theft

Module

4. ECM

5. Instrument

Engine Anti-theft warning
lamp always on, the engine
can not start.

6. Wiring

Harness

Refer to 2.5.7.17 Engine
Anti-theft Warning Lamp
Flashing, Vehicle Can Not
Start

388

Connector

1. Anti-theft

Coil

—

Anti-theft system can not
detect the valid key.

2. Anti-theft

Module

—

1. Anti-theft

Coil

—

2. Anti-theft

Module

—

Keys do not match

3. Key

—

1. Wiring Harness and

Connector

2. Anti-theft

Module

ECM always detects Anti-theft
malfunction

3. ECM

Refer to 2.5.7.17 Engine
Anti-theft Warning Lamp
Flashing, Vehicle Can Not
Start

389

2.5.7.7 Replaced Key Programming

1

Measure VVT solenoid valve resistance.

2

Turn the ignition switch to the position "ON".

3 Enter

Anti-theft

System

Note: Before enter the security code please contact the manufacturers technical department, as
the Anti-theft computer will be locked after the wrong security code entered seven consecutive
times.

4

Enter the security code.

5 Learn

the

key.

6 Key

Programming.

7

Place the ignition switch at "OFF" position and wait about 5 min or so.

8

New key learn successful.

Next

Next

Next

Next

Next

Next

Next

390