Geely Emgrand X7. Manual part — 464
Geely Emgrand X7. Manual part - 464
Shoulder guide ring fixing nut of front row
safety belt
Inch 7/16
40-50
30-37
Upper fixing support of safety belt retractor
M6×15
8-10
6-8
9.3.2 Description and Operation
9.3.2.1 Description and operation
Seat belt
The front-row seats and the rear-row seats are both equipped with safety belts and these are the main means to
protect the passengers. The passenger can be kept in the passenger compartment via the safety belt with the
following conditions, and the impact force can be gradually reduced.
Face impact type
-
Rear impact type collision
-
Side impact type collision
-
Turnover type collision
All vehicles are equipped with an emergency locking retractor. Safety belt with self-lock function The locking
function is activated when quickly pulling the safety belt from the retractor completely. The locking function can
prevent the pull-out amplitude of the safety belt from exceeding the allowable rolling position.
Recommend to fix the child seat with the self-locking function. When the safety belt is completely rolled into the
emergency locking retractor, the function can be canceled. After the locking function is canceled, the safety belt is
unlocked. After the locking function is canceled, the safety belt can be pulled out from the retractor. This vehicle
is also equipped with an airbag system. See 9.2.2.1 Description and Operations in "Airbag System".
Seat safety belt warning lamp
The driver seat safety belt warning lamp and the passenger seat safety belt warning lamp are located on the
combination instrument and the multifunctional instrument displayer respectively to remind the client of wearing
the safety belt.
Child Seat Protection System
Warning: Do not use backward protective device for children on the passenger sear. When inflating the
passenger-side SRS, the child sitting in the backward protective device for children on the passenger seat
will be suffered fro severe injuries. If the forward protective device for children is applicable to your child,
make sure the front row of passenger chair moves backward as far as possible, and then install the
protective device for children. Ensure the position of the protective device for children does not conflict
with any additional requirements of the manufacturer. See the user manual of the automobile as well as the
user guide attached in the protective device for children for details.
Child seat can only be used for the forward seating position. The child seat should be installed and fixed according
to the guidance of the manufacturer. If the child seat is equipped with an upper strap, need to fix the seat. If the
safety belt on the seat is used for fixing the child seat, the seat shall not be allowed to sit.
1855
9.3.3 System operating principle
9.3.3.1 System operating Principle
Front row seat safety belt system
The front row of seat safety belt system comprises driver and passenger seat safety belt pre-tightener retractors, a
passenger identification sensor and two front rows of seat safety switches. The passenger recognition sensor is
used for detecting whether the passenger seat is occupied by a passenger. If unmanned via detection, turn off the
passenger safety belt warning lamp. Two front rows of seat safety belt switches are located in the seat lock catches
respectively for controlling the safety belt warning lamp and the buzzer.
1. Driver seat safety belt warning lamp
After the ignition switch is ON, the airbag electronic control unit (ACU) detects the status of the driver's seat belt
and sends out a signal to the combination instrument through the CAN bus if the driver's seat belt is not fastened,
the driver seat safety belt warning lamp on the combination instrument flashes, and the buzzer sounds for 4s to
remind the driver of wearing the safety belt.
2. Passenger seat safety belt warning lamp.
When the ignition switch is in the position ON, a passenger identification sensor detects whether the passenger
seat is occupied and sends out a signal to the electronic control unit of the airbag. The airbag electronic control
unit detects the condition of the passenger seat belt and sends to the instrument assembly a signal. Then the
combination instrument assembly sends to the multi-functional instrument a signal and requests the passenger seat
belt warning lamp to flicker or go out.
Rear row of seat safety belt system
The rear row of seat safety belt system comprises the following parts:
-
Rear row seat safety belt retractor and safety belt assembly; safety belt retractor is located under the rear
stand trimming plate and its lower section is fixed on the floor.
-
Rear row seat safety belt buckle and middle row seat safety belt buckle; buckle is fixed on the floor by the
buckle.
1856
9.3.4 Component position
9.3.4.1 Component position
Passenger identification sensor
NL09-2008b
1857
9.3.5 Electrical schematic diagram
9.3.5.1 Electrical schematic diagram
NL09-2007b
乘员检测传感器
驾驶员安全带开关
S
R
S
多功能仪表总成
组合仪表总成
乘客安全带开关
Combination instrument
assembly
Passenger inspection sensor
Driver safety belt switch
Passenger safety belt switch
Multi-function instrument
assembly
1858
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст