Geely Emgrand X7. Manual part — 7

Lay the air bag components and store it upwards.

–

When storing, keep the air bag components dry.

–

When carrying airbag components, do not touch the electrode and keep the airbag away from
body as far as possible.

–

When placing air bag components, put the protective cover upwards.

–

Check if airbag component was damaged carefully.

–

Disconnect the battery negative before connecting airbags cable. Wait 60s, standing beside
airbag components.

–

Correct adjusted and maintenance all equipment

–

After deploying an airbag, make sure wash your hands.

Airbag-- operations to be avoided

–

Do not store flammable materials and components together with gas generator.

–

Do not immerse the airbag assembly in water or let airbag assembly contact with other
liquids.

–

Gas generator can not be stored under the ambient temperature above 80ºC/176ºF

–

Can not stored as an upside-down way

–

Can not be try to open gas generator housing

–

Do not expose the gas generator to flame or heat.

–

Do not place other items on the components cover.

–

Can not used damaged module

–

Do not touch the component or the gas generator within 10 min of airbag being deployed.

–

Do not use electrical probe in the return circuit.

1.6.1.4 A/C refrigerant

Refer to 1.6.1.10 chemical materials.

Skin contact may cause frostbite.

Must comply with the instructions provided by the manufacturer to avoid the exposed lights. Wear
suitable protective goggles and protective gloves.

If refrigerant come into contact with skin or eyes, you should immediately wash the contacted area
with water.

Apply the appropriate cleaning solution and rinse the eyes. Do not rub, as the case may need to
seek medical assistance.

A/C Refrigerant- operations to be avoided

–

Do not store refrigerant at a place with direct sunlight or heat sources.

–

When filling, the refrigerant bottles must not be upright, keep valves down.

–

Refrigerant cylinder can not exposed in the snow area

–

Can not be drop off refrigerant cylinder

–

Do not.in any case. Directly discharge refrigerant to the atmosphere.

27

–

Can not be mix refrigerant. For example: R12 (dichlorodifluoromethane) and R134a
(tetrafluoroethane).

1.6.1.5 Adhesives and sealant

Precaution of adhesive and sealant

Before applying adhesive/sealant, the surface shall be cleaned and special detergent shall be used
to avoid the result of adhesive/sealant. Do not let the room-temperature curable glue into the
threaded blind hole when using sealant; if the room-temperature curable sealant enters into the
threaded blind hole, the fastener during fastening may produce the hydraulic locking effect,
thereby resulting in the damage to the fastener and (or) the other components; moreover, the
fastener during fastening is unable to obtain a correct clamping force, so that the sealing effect of
the sealant is worse, thereby leading to that the fastener can not be fastened correctly to loose or
separate the part and further resulting in seriously damage to the parts of the engine and the like.

Health and safety

The material in adhesive/sealant contains harmful substances. Prolonged exposure may cause
acute or chronic intoxication, occupational disease and skin disease. When applying, air
ventilation device shall be used to keep ventilated. When operating, it is necessary to wear
protective gloves, mask and protective clothing.

–

Remove waste adhesive or wastes polluted by solvent. They are not allowed to accumulate
for a long time.

–

Adhesive/sealant shall be stored in non-smoking area. Before using, clean them and apply
them with applicator or container.

Maintenance for adhesive/sealant

When the vehicle faults or has an accident, the body will be deformed, the steel plate will be
cracked, and the welding spot will be fallen off; at times, the engine, the chassis and the other
assemblies are further locally damaged, thereby resulting in shedding and damage of some
adhesive/sealant products. During the course of maintenance, adhesives with the same
performance shall be selected according to materials and functions of components.
Adhesive/sealant that can be used during the course of maintenance can be used as follows.

Body maintenance

After interior and steel plate is deformed or cracked, adhesive applied on the body falls off or is
cracked. During the course of maintenance, the damaged position shall be applied by adhesive
again.

–

First remove adhesive on the surface of body with a small knife. Remaining adhesive shall be
cleaned with alcohol;

–

Use special detergent to clean the applied position to avoid any foreign material on the
surface to be applied.

–

Apply adhesive on the original position again to achieve bonding and sealing result.

Adhesive for body maintenance

Products Material

Function

Recommended

model

Vehicle sealant

Mono-component
polyurethane

Bonding of body skin, interior and
exterior trim and body structure
and other components.
The adhesive has strong binding
strength and cohesion as well as
good adhesion with metal and a

Tianshan
TONSAN

:1922, 1923/

28

variety of painted surface, etc.

Welded seam
sealant

Mono-component
polyurethane

1. Room temperature curing

adhesive is used for sealing of
welding joint inside vehicle
body. Use brush to apply
adhesive manually.

2. Indoor temperature curing

adhesive is used for sealing of
foldable end of engine hood,
boot and door. Use special
glue gun to apply adhesive
along the line.

Chinese
automotive
components
industry
company:C8802

Chip-resistant
primer

Rubber and Resin

Anti-collision glue for protecting
the room temperature curing-type
chassis forms a permanent
anti-aging flexible
corrosion-resistant protect coating
in the underbody and the wheel
guard.
Such products can replace the PVC
coating and have excellent
anti-rusting, sound insulation and
rock impact resistance.

Chinese
automotive
components
industry
company:C312DW

Windscreen glue

Mono-component
polyurethane

Polyurethane adhesive cured at
room temperature is used for
sealing glass for vehicle window.
This glue has good bonding
property and can react with
moisture in the air. The glue has
strong strength, age resistance,
vibration and fatigue resistance,
low temperature resistance and no
corrosion and other good
properties after curing.

Tianshan.Kesaier

: 1956、1924

Detergent ——

Clean all interface contact with
base coating and adhesives,

Pressure-sensitive
adhesive tape

Acrylic adhesive
tape

It is used for bonding of rubbing
strips, nameplates, guard plates,
splash guard, door protection,
body, various trim strips and so on.
This adhesive tape is excellently
weather endurable and durable and
is mainly used for bonding rubber
sealing strip system on a vehicle.

3M 4229P、4215、
4221L

Heat-Sensitive
Adhesive Tape

Acrylic adhesive
tape

This adhesive tape has very strong
bonding force which can avoid
clearance and corrosion caused by
unsecured adhesion and it can
provide strong sealing effect.

3M 4237P

Adhesive with
primer

——

Different primers are selected for
different materials of bonding
surface. The bonding surface must

3M C-100、
K-500\520、N-200

29

be clean, the primer is uniformly
applied on the sticky surface via a
brush after completely drying, and
the adhesive tape is pasted after
driving.

Component maintenance

After components, engine and transmission are damaged, it is necessary to apply cohesive and
sealant again. Before applying, please clean all the surfaces to remove burr and crack.

Adhesive and sealant for components

Description Function

Recommended

model

Silicon rubber plane
sealant

Be used for the plane sealing of the large
clearance and the flexible connecting piece,
such as the box body, the flange, the joint
surface of the bottom shell and the end cover
and other parts; clean up the adhesive residue of
the sealing surface prior to gluing, apply sealing
glue line with proper diameter on the sealing
surface (or gasket) after cleaning and drying,
align and close the part immediately after gluing
to avoid misplacing, tighten the bolt, wipe the
unnecessary extrusive glue or clean up by the
blade after curing.
This kind of sealant does not contain solvent
and become curing at room temperature, with
corrosion resistance, impact resistance, medium
resistance and temperature resistance.

Tianshan.Kesaier :
1596/1598～1596

Anaerobic thread
sealant

Used to tighten and lock bolts, nuts and screws.
Before applying, please clean all engaged
surfaces. After it becomes dry, apply sealant on
engaged surface.
After it becomes curing, it has good impact
resistance, vibration resistance, no leakage,
corrosion resistance.

Tianshan.Kesaier :
1243、1242

Anaerobic sealant

Used to seal flat surface which has small
clearance and is required to be cured without
air, and lock bolts.
It has performances such as waterproof, oil
resistance and corrosion resistance.

Loctite

204，

Tianshan.kesaie :
1510

Other maintenance materials

Description Function

Material

No.

Locking adhesives

Used to lock tightening thread with maximum
dimension M6, like door window regulator
handle

Loctite thread
locking adhesive

Corrosion inhibitor

It is a kind of corrosion inhibitor that is mainly
made of plastic. It is used for soundproof and
corrosion resistance treatment for chassis, with
corrosion resistance and soundproof.

Fudun

30