Geely Emgrand X7. Manual part — 254
Geely Emgrand X7. Manual part - 254
18. Connect the engine wiring
harness to the engine cabin
junction box connecting cables
and connectors.
19. Install fixing bolts of clutch slave
cylinder.
Torque :20Nm (Metric) 14 . 8lb-ft
(English system)
20. Install and tighten the fixing bolts
of clutch oil pipe bracket.
Torque:10Nm(Metric) 7.4lb-ft(English
system)
21. Install the vacuum booster
vacuum tubes.
22. Install the radiator inlet and outlet
pipes.
NL02-0181b
23. Install radiator water outlet pipe.
24. Install the intake main pipe
assembly.
25.
Install the air-conditioning
compressor high and low
pressure connecting pipes.
Torque :18Nm (Metric) 13 . 3lb-ft
(English system)
26. Connect the front and rear
oxygen sensor harness
connectors.
27. Connect the engine control unit
and engine harness to the
instrument panel harness
connectors.
28. Install grove box of instrument
desk .
29. Install battery and bottom plate.
30. Install the Coolant Recovery
Reservoir.
31. Fill engine coolant.
32.
Fill the air-conditioning
refrigerant .
33. Connect the battery negative
cable .
NL02-0180b
1015
2.13.8.14 Replacement of Cylinder Hood Assembly
Dismantlement Procedure
1. Disconnect the battery negative electrode cable. Refer to 2.11.8.1 Battery Disconnection.
2. Dismantle the plastic shield of engine. Refer to 2.13.8.1 Replacement of Plastic Shield of
Engine.
3. Refer to 2.29.8.1 Engine Coolant Discharge and Filling to discharge the engine coolant.
4. Refer to "Replacement of Throttle Body Assembly" to dismantle the throttle body.
5. Refer to 2.13.8.6 "Replacement of Intake Manifold Assembly" to dismantle the intake
manifold assembly.
6. For dismantlement of the exhaust manifold, see "2.7.6.1 Replacement of Exhaust Manifold".
7. Dismantle ignition coil and ignition guide wire. refer to“2 . 10 . 8 . 3 ignitioncoil
replacement ” .
8. Refer to 2.13.8.2 "Replacement of Cylinder Hood Cover" to dismantle the cylinder hood
cover.
9. Refer to 2.13.8.3 "Replacement of Drive Belt" to dismantle the drive belt.
10. Dismantle the engine mounting. Refer to 2.13.8.7 Replacement of Engine Mount.
11. Refer to 2.13.8.10 "Replacement
of Timing Chain Cover" to
dismantle the timing chain cover.
12. Refer to 2.13.8.10 "Replacement
of Timing Chain" to dismantle
the timing chain.
13. Refer to 2.2.8.2 “Replacement of
Fuel Injector” to dismantle the
fuel distributing pipe assembly.
14. Refer to 2.2.8.6 "Replacement of
temperature sensor of engine
coolant" to disconnect the
temperature sensor of engine
coolant harness connector.
15. Refer to 2.10.8.1 "Replacement
of Camshaft Position Sensor" to
dismantle camshaft position
sensor.
16.
For dismantling of VVT
electromagnetic valve, refer to
"2.2.8.4VVT Replacement of
electromagnetic valve and
cleaning of electromagnetic valve
filter element".
FE02-0187b
1016
17. Refer to 2.13.8.12 “Replacement
of Camshaft” to dismantle the
camshaft.
18. Dismantle the radiator inlet
pipes.
19. Dismantle the warm water pipe
for the heater tank.
FE02-0188b
20. Dismantle the fixing bolts of
small cycle pipes cylinder head.
FE02-0189b
21. Dismantle the cylinder hood
bolts according to the sequence
in the figure.
Note: When the engine is hot, it is
prohibited to dismantle the cylinder
hood, as this will cause the cylinder
hood distortion.
1
7
9
6
4
3
5
10
8
2
FE02-0190b
1017
22. Remove the cylinder hood bolts.
Note: Due to confined space, cylinder
head bolts and bolt gaskets can not
be removed together.
FE02-0191b
23. Remove the cylinder hood bolt
gasket with a magnetic stick.
FE02-0192b
24. Dismantle the cylinder hood
gasket.
FE02-0193b
1018
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст