Geely Emgrand X7. Manual part — 347
Geely Emgrand X7. Manual part - 347
5
Use fault diagnosis tester to confirm if DTC is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switch to ON position.
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
6 Troubleshooting
5. Maintenance
guide:
Replace Automatic transmission control module, refer to3.5.7.8 replace automatic transmission control module
Yes
No
Next
Refer to 2.2.7.3 Intermittent Fault Inspection for
intermittent fault.
1387
3.5.7.30 U160E
1. DTC
description:
DTC U160E BOSCH underlying software error
The hardware and underlying software of the transmission control unit (TCU) are designed by BOSCH. When the
underlying software of the transmission control unit (TCU) encounters an error, the system will report this
diagnostic testing code (DTC).
2. Conditions For Setting DTC and The Fault Position :
DTC code
DTC detection
strategy
Conditions for setting the DTC (control
strategy)
Fault position s
U160E
Hardware circuit
Inspection
1.ignition switch is in ON position
1. TCU
3. Diagnostic
procedures:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and analyze the
accuracy of the data, as these will help with quick diagnosis.
1
Read the fault code again after clearing away the fault code to Check if fault codes, except DTC
U160E exist in the control system.
A. Connect fault diagnosis tester to the datalink connector.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic device power supply
D. Clear DTC code.
E. Reset reading fault code, and check if DTCs meet setting condition of fault code in current
DTC Codes Shown
To Step
DTC U160E
Yes
DTC other than DTC U160E
No
2
Switch off the ignition switch, and then switch on the ignition switch again,
No
Yes
Refer to3.4.7.6 fault diagnosis code (DTC)
chapter index
1388
3
Switch off the ignition switch again, and then switch on the ignition switch again,
4
Switch off the ignition switch again, and then switch on the ignition switch again,
5
Use fault diagnosis tester to confirm if DTC is stored again .
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switch to ON position.
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
6 ReplaceTCU
Refer to3.5.7.8 replace automatic transmission control module
7
Go to automatic transmission fresh process.
Refer to3.5.7.4 Automatic transmission refresh process
8
Use fault diagnosis tester to confirm if DTC is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switch to ON position.
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
Next
Next
Next
No
Yes
Troubleshooting
Next
Next
1389
9 Troubleshooting
5. Maintenance
guide:
Replace Automatic transmission control module, refer to3.5.7.8 replace automatic transmission control module
Yes
No
Refer to 2.2.7.3 Intermittent Fault Inspection for
intermittent fault.
1390
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст