Geely Emgrand X7. Manual part — 346
Geely Emgrand X7. Manual part - 346
ECM
BCM
IP
ACU
ABS
TCU
DLC
SL03-0040c
4. Diagnostic
procedures:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and analyze the
accuracy of the data, as these will help with quick diagnosis.
1
Read the fault code again after clearing away the fault code to check if fault codes, except DTC
U0100, U0121, U0146 and U0415 exist in the control system.
A. Connect fault diagnosis tester to the datalink connector.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic device power supply
D. Clear DTC code.
E. Reset reading fault code, and check if DTCs meet setting condition of fault code in current
DTC Codes Shown
To Step
DTC U0100 U0121 U0146 U0415
Yes
DTCs other than DTCs U0100, U0121, U0146 and U0415
No
1383
2
Detect TCU CAN bus circuit
See 11.17.7.6 diagnosis of CAN bus signal.
Whether the CAN bus is open circuited or short circuited?
3 ReplaceTCU
Refer to3.5.7.8 replace automatic transmission control module
4
Go to automatic transmission fresh process.
Refer to3.5.7.4 Automatic transmission refresh process
5
Use fault diagnosis tester to confirm if DTC is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switches to ON position.
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
6 Troubleshooting
5. Maintenance
guide:
Replace Automatic transmission control module, refer to3.5.7.8 replace automatic transmission control module
No
Yes
Refer to3.4.7.6 fault diagnosis code (DTC) chapter
index
Next
Yes
No
Next
Refer to 2.2.7.3 Intermittent Fault Inspection for
intermittent fault.
Yes
No
Maintenance circuit fault
1384
3.5.7.29 U1601 U1606 U1607 U1608 U1609
1. DTC
description:
DTC U1601 TCU application software lost or damaged
DTC U1606 TCU calibration error–platform
DTC U1607 TCU calibration error-activate the derived calibration
DTC U1608 TCU VIN (vehicle identification number)-coding error
DTC U1609 TCU hardware (pcb) calibration error
The transmission control unit software or calibration software can be upgraded online. These DTC protection
transmission control units prevent the documents damaged from loading to the transmission control unit. They
further ensure only the correct calibration parameter and software version can be loaded into the current
transmission control unit (TCU) for use.
2. Conditions for setting DTC and the fault position :
DTC code
DTC detection
strategy
Conditions for setting the DTC (control
strategy)
Fault position s
U1601
U1606
U1607
1. ignition switch is in ON position
2. CRC is ineffective.
U1608
1. ignition switch is in ON position
2. VIN is not consist with rated concent
U1609
Hardware Circuit
Inspection
1. ignition switch is in ON position
2. TCU made messages are not exist
1. TCU
3. Diagnostic
Procedures:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and analyze the
accuracy of the data, as these will help with quick diagnosis.
1
Read the fault code again after clearing away the fault code to Check if fault codes, except DTC
U1601, U1606, U1607, U1608 and U1609 exist in the control system.
1385
A. Connect fault diagnosis tester to the datalink connector.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic device power supply
D. Clear DTC code.
E. Reset reading fault code, and check if DTCs meet setting condition of fault code in current
DTC Codes Shown
To Step
DTC U1601 U1606 U1607 U1608 U1609
Yes
DTCs other than DTCs U1601, U1606, U1607, U1608 and U1609
No
2
Update the TCU calibrated software.
3
Use fault diagnosis tester to confirm if DTC is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switches to ON position.
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
3 ReplaceTCU
Refer to3.5.7.8 replace automatic transmission control module
4
Go to automatic transmission fresh process.
Refer to3.5.7.4 Automatic transmission refresh process
No
Yes
Refer to3.4.7.6 fault diagnosis code (DTC) chapter
index
Next
Next
No
Yes
Troubleshooting
1386
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст