Geely Emgrand X7. Manual part — 194
Geely Emgrand X7. Manual part - 194
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the rear oxygen
sensor harness connector EN03.
(c) Rotated ignition switch to ON
position .
(d) Measure resistance between rear
oxygen sensor EN03 terminal A
and a reliable ground.
Standard Resistance: Less than 1 Ω
(e) Connect the rear oxygen sensor
harness connector EN03.
NL02-2067b
A
B
C
D
EN03 后氧传感器线束连接器
A
Is resistance the specified value?
Step 10
Replace the rear oxygen sensor.
Step 11
Inspect the rear oxygen sensor signal circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the rear oxygen
sensor harness connector EN03.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between rear
oxygen sensor wiring harness
connector EN03 terminal B and
ECM harness connector terminal
No.48. Inspect whether the
circuit is open. otherwise, repair
the faulty part.
NL02-2066b
A
B
C
D
EN03 后氧传感器线束连接器
B
Next
Go to step 15
No
Go to step 12
Yes
EN03 rear oxygen sensor harness connector
EN03 rear oxygen sensor harness connector
775
(e) Measure resistance between rear
oxygen sensor harness connector
EN03 terminal No.B and a
reliable ground. Inspect whether
the circuit is short to ground. If
there is no short circuit, repair the
faulty part.
(f) Measure voltage between rear
oxygen sensor harness connector
EN03 terminal No.B and a
reliable ground. Inspect whether
the circuit is short to power
supply. If there is no short circuit,
repair the faulty part.
NL02-2068b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
48
Test Items
Standard Value
EN03(B)-EN01(48) Resistance value
Less than 1 Ω
Resistance Between EN03 (b) and a Reliable
Ground
10kΩ 或更高
Voltage Between EN03 (b) and a Reliable Ground
0V
Step 12
Inspect rear oxygen sensor ground circuit
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the rear oxygen
sensor harness connector EN03.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between rear
oxygen sensor wiring harness
connector EN03 terminal A and
ECM harness connector terminal
No.73. Inspect whether the
circuit is open. otherwise, repair
the faulty part.
NL02-2067b
A
B
C
D
EN03 后氧传感器线束连接器
A
Normal
Go to step 13
EN01 engine control module harness
connector
EN03 rear oxygen sensor harness connector
776
(e) Measure resistance between rear
oxygen sensor harness connector
EN03 terminal No.A and a
reliable ground. Inspect whether
the circuit is short to ground. If
there is no short circuit, repair the
faulty part.
(f) Measure voltage between rear
oxygen sensor harness connector
EN03 terminal No.A and a
reliable ground. Inspect whether
the circuit is short to power
supply. If there is no short circuit,
repair the faulty part.
NL02-2061b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
73
Test Items
Standard Value
EN03(A)-EN01(73)Resistance value
Less than 1 Ω
Resistance Between EN03 (a) and a Reliable Ground
10kΩ 或更高
Voltage Between EN03 (a) and a Reliable Ground
0V
Execute next step as per normal.
Step 13
Inspect the ECM Power Supply Circuits.
(a) Inspect whether ECM power supply circuit is normal.
(b) Inspect whether ECM ground circuit is normal.
Step 14
Replace ECM
(a) Refer to 2.12.8.1 Replacement of Engine Control Module to Replace ECM.
(b) Carry out the crankshaft position sensor learning, refer to 2.12.7.11 “Crankshaft Position
Sensor (CKP) Learning.
Step 15
Use fault diagnosis tester to confirm if DTC is stored again .
No
Repair the faulty part.
Yes
Next
Next
EN01 engine control module harness
connector
777
(a) Connect the fault diagnosis tester to the diagnostic interface.
(b) Turn ignition switch to ON position.
(c) Clear DTC code.
(d) Start and run the engine at idle speed to warm up the engine for at least 5 min.
(e) test the vehicle on the road for at least 10 min.
(f) Read control system DTC code again to confirm that the system has no DTC code.
Step 16
Troubleshooting
5. Maintenance
guide
:
Refer to 2.4.6.1 “Replacement of Rear Oxygen Sensor” to replace the rear oxygen sensor.
No
Repair the faulty part.
Yes
778
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст