Geely Emgrand X7. Manual part — 199
Geely Emgrand X7. Manual part - 199
No.B and a reliable ground.
(f) Install the engine main relay.
(g) Connect cylinder No.1 fuel
injector harness connector EN11.
Exclude the fuel injector power supply
circuit fault.
ER03
85
86
87
30
30
87
86
85
ER05
30
87
86
85
ER06
30
87
87a
86
85
ER11
ER08
ER0
9
85
86
87
30
ER10
2
1
5
3
2
1
5
3
2
1
5
3
ER04
ER02
2
1
5
3
2
1
5
3
ER01
ER07
2
1
5
3
1
2
3
4
11
12
13
14
15
16
5
6
7
8
9
10
EF0
8
EF0
7
EF2
7
EF2
6
EF2
2
EF2
9
EF0
3
EF0
6
EF0
9
EF2
5
EF1
7
EF1
6
EF1
5
EF3
5
EF2
1
EF
1
4
EF
0
1
EF
0
2
EF
0
4
EF
1
0
EF
1
1
EF
1
8
EF
2
4
NL02-0045c
Test Items
Standard Value
EN11(b) and main relay No,30 terminal
Less than 1 Ω
EN11(b) and reliable grounding
10 kΩ or higher
Step 6
Inspect the Cylinder #1 fuel injector control circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect cylinder No.1 fuel
injector harness connector EN11.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between
cylinder No.1 fuel injector wiring
harness connector EN01 terminal
No.A and ECM harness
connector terminal No.6. Inspect
whether the circuit is open. If
there is no open circuit, repair the
faulty part.
NL02-2079b
A
B
EN11 1缸燃油喷射器线束连接器
B
Go to step 9
Next
EN11 1st cylinderfuel injector harness
connector
795
(e) Measure resistance between
cylinder No.1 fuel injector wiring
harness connector EN11 terminal
No.A and a reliable ground.
Inspect whether the circuit is
short to ground. Otherwise,
repair the faulty part.
(f)
Measure voltage between
cylinder No.1 fuel injector
harness connector EN11 terminal
No.A and a reliable ground.
Inspect whether the circuit is
short to power supply. Otherwise,
repair the faulty part.
NL02-2080b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
6
Test Items
Standard Value
EN11(A)-EN01(6)Resistance value
Less than 1 Ω
EN11(A)-reliable grounding resistance value
10 kΩ or higher
EN11(A)-Reliable grounding voltage value
0V
Execute next step as per normal.
Step 7
Inspect the ECM Power Supply Circuits.
(a) Inspect whether ECM power supply circuit is normal.
(b) Inspect whether ECM ground circuit is normal.
Step 8
Replace ECM
Refer to 2.12.7.11 Crankshaft Position Sensor (CKP) Learn to carry out the crankshaft position
sensor learn after replacing the ECM.
Step 9
Use a fault diagnosis tester to confirm whether the DTC Code is stored again.
(a) Connect fault diagnosis tester to the diagnostic interface.
Next
No
Repair the faulty part.
Yes
Next
EN01 engine control module harness
connector
796
(b) Turn ignition switch to ON position.
(c) Clear DTC code.
(d) Start and run the engine at idle speed to warm up the engine for at least 5 min.
(e) Road test the vehicle for at least 10 min.
(f) Read control system DTC code again to confirm that the system has no DTC code.
Step 10
Troubleshooting
5. Maintenance
guide
:
Refer to 2.3.8.5 “Replacement of Fuel Injectors” to replace the fuel injectors
No
Refer to 2.12.7.3 Intermittent Fault
Inspection for intermittent fault.
Yes
797
2.12.7.30 DTC P0264 P0265
1. DTC
description:
DTC P0264
Cylinder No.2 Fuel Injector Circuit Low Voltage Fault
DTC P0265
Cylinder No.2 Fuel Injector Circuit High Voltage Fault
Fuel injectors operating voltage is provided by The Main Relay controlled by ECM. Battery
voltage passes through the main relay terminal No.3 to all fuel injector wiring harness connectors
terminal No.A. ECM controls fuel injector ground circuit by ECM harness connector EN01
terminal No.8. ECM monitors all fuel injector driver circuits status, if ECM detects driving circuit
status corresponding voltage is incorrect, ECM will set a fuel injector control circuit fault DTC
code.
2. Conditions For Setting DTC and The Fault Location:
DTC Code
DTC Detection
Strategy
Conditions For Setting The DTC
(Control Strategy)
Fault Locations
P0264
Hardware
Circuit
Inspection
Injector Signal Circuit Open or
Short To Ground
P0265
Hardware
Circuit
Inspection
Injector Signal Circuit Short To
Power Supply
1. Sensor
Circuit
2. Sensor
3. ECM.
3. Circuit
sketch
NL02-2081b
44
EN01
ECM
BAT
15
A
E
F2
1
MPR
86
87
30
85
发动机主继电器
8
EN01
A
EN12
B
EN12
INJD
2缸燃油喷射器
Engine main
relay
2nd cylinderfuel
injector
798
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст