Geely Emgrand X7. Manual part — 547
Geely Emgrand X7. Manual part - 547
6
Repair the fault point between the left front window switch wire harness connector and
the BCM circuit.
(a) Repair fault points between left front window switch wire harness connector DR10 terminal
No. 20, 19 and 18 corresponding to BCM wire harness connector IP50 terminal No. 39, 19
and 3.
(b) Connect glass lifter switch wire harness connector.
(c) Connect to BCM harness connector IP50,
(d) Connect battery negative cable.
(e) Turn on ignition switch to position "ON".
(f) Operate left front window glass lifter switch.
Confirm whether the left glass lifter works normally.
7
Inspect the voltage among the terminal No. 20, 19 and 18 of the left front window wire
harness connector DR10 and the body.
(a) Disconnect left front window
harness connector DR10.
(b) Measure terminal voltage by
millimeter.
NL11-4013b
DR10 左前门玻璃升降器开关线束连接器
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
18
19
20
Test terminal
Terminal voltage
DR20(20)—grounding Signal
voltage
5V
DR20(19)—grounding Signal
voltage
5V
Yes
The system is normal.
No
Yes
Go to step 7
No
DR10 left frontdoor glass lifter
switchharness connector
2187
DR20(18)—grounding Signal
voltage
5V
Confirm if the voltage conforms to standard value.
8
Inspect the resistance of the BCM wire harness connector IP47 terminal and the left front
glass lifting motor wire harness connector DR02.
(a) Closed ignition switch to position
OFF.
(b) Disconnect the battery negative
cable.
(c) Disconnect BCM harness
connector IP47.
(d) Use multimeter to measure
connection situation of circuit.
NL11-4016b
A
B
DR02 左前门玻璃升降电机线束连接器
A
B
Test terminal
Terminal voltage
DR20(20)——grounding Signal
voltage
5V
DR20(19)——grounding Signal
voltage
5V
DR20(18)——grounding Signal
voltage
5V
Confirm if the resistance conforms to standard value.
9
Repair or replace the harness.
(a) Repair or replace wire harness between BCM wire harness connector IP47 terminal No. 8
and 7 corresponding to left front door glass lifting point wire harness connector DR02
terminal No. B, A.
(b) Connect BCM wire harness connector IP47.
(c) Connect to Left front door glass lifter harness connector.
Yes
Go to step 10
No
No
Go to step 11
Yes
DR02 left front doorglass lifting motor
harness connector
2188
(d) Connect battery negative cable.
(e) Turn on ignition switch.
(f) Operate left front window switch.
Confirm whether the glass lifter works normally.
10
Inspect the left front glass motor wire harness connector DR02 terminal voltage.
(a) Disconnect left front door glass lift motor harness connector DR02.
(b) Operated Left front door and window switch button.
(c) Use multimeter to measure voltage between left front glass lifter wire harness connector
DR02 terminal No. A and B.
Test terminal
Test conditions
Conduction condition
DRO2(A)—DR02(B)
LF WINDOW UP
12-14V
DRO2(A)—DR02(B)
LF WINDOW DOWN
12-14V
DRO2(A)—DR02(B)
LF WINDOW DOWN OTD
12-14V
Confirm if the voltage conforms to standard value.
11
Replace the BCM
Refer to 11.8.8.1 Replacement of BCM to replace BCM.
Confirm whether the glass lifter works normally.
12
Replace left front glass lift motor assembly ,
Refer to 11.4.8.5 Replacement of Left Front Glass Lifter Motor to replace the left front glass
lifting motor assembly.
Confirm the completion of repair.
Yes
The system is normal.
No
Yes
Go to step 12
No
Yes
The system is normal.
No
2189
If other single lifters without anti-trap window do not work, refer to the fault diagnosis process of
the left front door glass lifter.
13
The system is normal.
Yes
The system is normal.
No
2190
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст