Geely Emgrand X7. Manual part — 34
Geely Emgrand X7. Manual part - 34
P0011
Intake VCP Phase Response
Lag Behind
None
No malfunction
condition is
detected.
P0012
Intake VCP Camshaft Phase
Error is Big
VCP Inoperation
No malfunction
condition is
detected.
P0016
Intake VCP Camshaft Gear
Learn Bias Out of Range
OCV Cleaning Function
Enabled; VCR Inoperative
No malfunction
condition is
detected.
P0026
Intake VCP Hydraulic Control
Valve Clinch
OCV Cleaning Function
Enabled; If cleaning
failed, VCR is inoperative
No malfunction
condition is
detected.
P0076
Intake VCP Hydraulic Control
Valve Coil Low Voltage or
Open Circuit
VCP Inoperation
No malfunction
condition is
detected.
P0077
Intake VCP Hydraulic Control
Valve Coil High Voltage
VCP Inoperation
Next key cycle,
no malfunction
condition
detected.
P0340
Intake VCP Camshaft Position
Sensor Status Diagnosis
VCP Inoperation, Ignition
Angle
No malfunction
condition is
detected.
P0341
Intake VCP Target Wheel
Diagnosis
VCP Inoperation, Ignition
Angle
No malfunction
condition is
detected.
P0106
Intake Pressure/Throttle
Position Fault
(1) When Key is in ON
position, the system will
intake air in default form.
Manifold pressure value of
100 kPa
(2) When the engine is
running, the system uses
Manifold pressure value
No malfunction
condition is
detected.
P0107
Manifold air pressure sensor
circuit has low voltage or is
open
(1) When Key is in ON
position, the system will
intake air in default form.
Manifold pressure value of
100 kPa
(2) When the engine is
running, the system uses
Manifold pressure value
No malfunction
condition is
detected.
P0108
Intake Air Pressure Sensor
Circuit High Voltage
(1) When Key is in ON
position, the system will
No malfunction
condition is
135
intake air in default form.
Manifold pressure value of
100 kPa
(2) When the engine is
running, the system uses
Manifold pressure value
detected.
P0112
Intake Air Temperature Sensor
Circuit Low Voltage
P0113
Intake Air Temperature Sensor
Circuit High Voltage or Open
Circuit
System uses the default
intake air temperature
20°C
No malfunction
condition is
detected.
P0117
Coolant Temperature Sensor
Circuit Low Voltage
P0118
Coolant Temperature Sensor
Circuit High Voltage or Open
Circuit
(1) System calculates the
engine coolant
temperature, up to 98°C,
based on intake air
temperature and when Key
On and the engine running
time
(2) There is a malfunction
present, high or
Low-Speed fan turned on.
No malfunction
condition is
detected.
P0131
Front Oxygen Sensor Circuit
Short to Low Voltage
system enters open loop
fuel control.
No malfunction
condition is
detected.
P0132
Front Oxygen Sensor Circuit
Short to High Voltage
system enters open loop
fuel control.
No malfunction
condition is
detected.
P0133
Slow response of front oxygen
sensor
None
No malfunction
condition is
detected.
P0134
Front oxygen sensor heater
fails
system enters open loop
fuel control.
No malfunction
condition is
detected.
P0135
Pre-catalytic Oxygen
Indicating Mixture Too Thick
During Deceleration
Open Loop Control; Front
Oxygen Sensor Heater
Inoperation
Next key cycle,
no malfunction
condition
detected.
P1167
Pre-catalytic Oxygen
Indicating Mixture Too Thick
During Deceleration
None
No malfunction
condition is
detected.
P1171
Pre-Catalytic Oxygen
Indicating Mixture Too Thin
During Acceleration
None
No malfunction
condition is
detected.
136
P0137
Rear Oxygen Sensor Circuit
Short to Low Voltage
None
No malfunction
condition is
detected.
P0138
Rear Oxygen Sensor Circuit
Short to High Voltage
None
No malfunction
condition is
detected.
P0140
Rear Oxygen Sensor Circuit
Open
None
No malfunction
condition is
detected.
P0141
Rear Oxygen Sensor Heater
Malfunction
Rear Oxygen Sensor
Heater Inoperation
Next key cycle,
no malfunction
condition
detected.
P0171
Mixture Too thin When
Non-idling
None
No malfunction
condition is
detected.
P0172
Mixture Too thick When
Non-idling
None
No malfunction
condition is
detected.
P2187
Mixture Too thin When idling
None
No malfunction
condition is
detected.
P2188
Mixture Too thick When idling
None
No malfunction
condition is
detected.
P0230
Fuel Pump Relay Fault
Vehicle can not start.
(1) Short-circuit
or open-circuit
fault can't be
detected.
Failure condition
(2) short splice to
power supply
fault, go to key
Cycle, D detect
invalid conditions
P0261
Fuel Injector 1 Low Voltage
Fault
P0264
Fuel Injector 2 Low Voltage
Fault
P0267
Fuel Injector 3 Low Voltage
Fault
P0270
Fuel Injector 4 Low Voltage
Prolonged malfunction,
reporting misfire (P0300);
Open Loop Control for the
system;
No malfunction
condition is
detected.
137
Fault
P0262
Fuel Injector 1 High Voltage
Fault
P0265
Fuel Injector 2 High Voltage
Fault
P0268
Fuel Injector 3 High Voltage
Fault
P0271
Fuel Injector 4 High Voltage
Fault
Next key cycle,
no malfunction
condition
detected.
P0300 Multi-Cylinder
Misfire
Catalytic converter
damaged, the system
enters open loop control.
in certain operating
conditions, fault lamp
flashes.
No malfunction
condition is
detected.
P0324
Knock Control System Fault
Ignition Back Angle
Next key cycle,
no malfunction
condition
detected.
P0325
No signal from knock sensor
Ignition Back Angle
Next key cycle,
no malfunction
condition
detected.
P0335
No signal from crankshaft
position sensor circuit
Vehicle can not start.
No malfunction
condition is
detected.
P0336
Crankshaft Position Sensor
Circuit Signal Interference
Ignition Back Angle; VCP
Inoperation
No malfunction
condition is
detected.
P1336
58-Tooth Gear Error Not
Learnt
No misfire diagnosis
New tooth
learning
successful
P0351
Cylinder 1 Ignition Coil
Malfunction
P0352
Cylinder 2 Ignition Coil
Malfunction
P0353
Cylinder 3 Ignition Coil
Malfunction
P0354
Cylinder 4 Ignition Coil
Malfunction
Prolonged Malfunction,
Reporting Misfire (P0300)
(1) Open Circuit,
No Malfunction
Condition
Detected. (2)
Short to power
supply. Next key
cycle, no
malfunction
condition
detected.
P0420
Low transformation efficiency
None
No malfunction
138
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст