Geely EC718, EC718RV, EC715, EC715RV. Manual part — 512
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 512
Installation Procedure:
FE12-0166b
1.
Install four retaining bolts on each side of the rear bumper
energy absorber.
Torque: 70 Nm (Metric) 51.8 lb-ft (US English)
FE12-0167b
2.
Install four rear impact bar retaining nuts.
Torque: 70 Nm (Metric) 51.8 lb-ft (US English)
3.
Clip the wiring harness clips.
4.
Install the rear bumper.
Body, Sheet Metal and Painting
Bumpers
12-37
12.5 Doors
12.5.1 Specifications
12.5.1.1 Fastener Tightening Specifications
Application
Model
Specification
Metric (Nm)
US English (lb-ft)
Left Front Door Assembly
Retaining Bolts
M8 × 23
30-38
22.1-28.0
Right Front Door Assembly
Retaining Bolts
M8 × 23
30-38
22.1-28.0
Left Rear Door Assembly
Retaining Bolts
M8 × 23
30-38
22.1-28.0
Right Rear Door Assembly
Retaining Bolts
M8 × 23
30-38
22.1-28.0
Car Lock Retaining Bolts
M6 × 12
9-13
6.7-9.6
Door Check Link Retaining
Bolts
M6 × 16
23-26
17.0-19.2
12-38
Doors
Body, Sheet Metal and Painting
12.5.2 Removal and Installation
12.5.2.1 Front Door Hinge Replacement
Removal Procedure:
1
FE12-0168b
1.
Remove the front fender. Refer to
2.
Remove the front door wiring harness dust cover and
disconnect harness connector (1).
3.
Remove the front door check link. Refer to
.
4.
Use a cleaning cloth to clean the door hinge surface and
use an oil pen or other marking tools to mark the door
hinge position on the front door surface.
5.
Remove the front door hinge to the front door retaining
bolts.
FE12-0169b
6.
Remove the front door.
7.
Use a cleaning cloth to clean the door hinge surface and
use an oil pen or other marking tools to mark the door
hinge position on the body surface.
8.
Remove the front door hinge to the body retaining bolts.
9.
Remove the front door hinges.
Installation Procedure:
FE12-0170b
1.
Install the front door hinge to the front door retaining bolts
and tighten to the specified torque after tuning.
Torque: 25 Nm (Metric) 18.5 lb-ft (US English)
Note
Refer to "Fastener Notices" in "Warnings and
Notices".
Body, Sheet Metal and Painting
Doors
12-39
FE12-0171b
2.
Install the front door.
3.
Connect the front door wiring harness connector and the
dust cover.
4.
Install the front door check link.
5.
Close the front door and inspect the door Clearance,
adjust if necessary.
6.
Install the front door hinge to the front door retaining bolts.
Torque: 25 Nm (Metric) 18.5 lb-ft (US English)
7.
Install the front fender.
8.
Install the front fender liner.
9.
Install the front wheel.
10. Lower the vehicle.
12.5.2.2 Front Door Check Link Replacement
Removal Procedure:
FE12-0172b
1.
Remove the front door trim panel. Refer to
Side Door Trim Panel Replacement
2.
Remove the front door check link retaining blots (2 M6, 1
M8).
3.
Remove the front door check link from inside of the front
door.
12-40
Doors
Body, Sheet Metal and Painting
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст