Geely EC718, EC718RV, EC715, EC715RV. Manual part — 301
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 301
6.4.5 Removal and Installation
6.4.5.1
Brake
Master
Cylinder
Tank
Replacement
Removal Procedure:
FE06-0031b
1.
Remove the brake master cylinder. Refer to
.
2.
Remove the brake master cylinder and the tank
connecting pin. From the brake master cylinder tank
remove and replace the seals.
Installation Procedure:
FE06-0032b
1.
Apply clean brake fluid to lubricate tank seals.
2.
Install the lubricated seal into the brake master cylinder.
3.
Install the tank to the brake master cylinder and install the
connecting pin.
4.
Install the brake master cylinder with the tank.
6.4.5.2 Brake Master Cylinder Replacement
Removal Procedure:
Warning!
Refer to 'Battery Disconnect Warning" in "Warnings and
Notices".
Brake System
Hydraulic Brake
6-37
1
2
3
2
FE06-0033b
1.
Disconnect the battery negative cable. Refer to
.
2.
Drain the brake fluid.
Note
Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice" in "Warnings and Notices".
3.
Disconnect the brake fluid level sensor wiring harness
connector (1), and remove the brake pipe connector nut
(2).
4.
Loosen clutch master cylinder to the tank hose clip (3),
and pull the hose from the tank.
FE06-0034b
5.
Plug the brake pipe openings to prevent brake fluid loss
and contamination.
6.
Remove the brake master cylinder retaining nuts.
7.
Remove the brake master cylinder with the tank, place the
brake master cylinder on a clean table.
FE06-0031b
8.
Remove the tank and the brake master cylinder
connection pin, separate the tank and the brake master
cylinder.
9.
Remove the brake master cylinder.
6-38
Hydraulic Brake
Brake System
Installation Procedure:
FE06-0032b
1.
Install the brake master cylinder to the tank connecting
pin.
FE06-0037b
2.
Install the brake master cylinder with the tank into the
vacuum booster.
3.
Tighten the brake master cylinder retaining nuts.
Torque: 25 Nm (Metric) 18.5 lb-ft (US English)
FE06-0038b
4.
Connect the brake fluid level sensor harness connector,
fix with the clutch master cylinder hose to the tank, tighten
the brake pipe connecting nut.
Torque: 16 Nm (Metric) 11.9 lb-ft (US English)
5.
Add brake fluid.
Note
Refer to "Adding Fluid to the Brake System Notice"
in "Warnings and Notices".
6.
Bleed air in the brake system. Refer to
Brake System Exhaust Procedure
7.
Bleed air in the clutch system. Refer to
8.
Check for leaks.
9.
Re-examine the brake fluid.
Brake System
Hydraulic Brake
6-39
10. Connect the battery negative cable.
6.4.5.3 Brake Hose Replacement (Front)
Removal Procedure:
Note
Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice" in "Warnings and Notices".
FE06-0039b
1.
Drain the brake fluid.
2.
Lift and support the vehicle. Refer to
.
3.
Remove the front wheels. Refer to
4.
Remove the brake hose and brake pipe connecting bolts,
pull out the spring, and remove the brake hose from the
bracket.
2
1
FE06-0040b
5.
Remove the brake hose bolts (1), disconnect the brake
hose from the shock absorber, remove the brake hose to
the brake cylinder connecting bolt (2).
6.
Remove the front brake hose.
Installation Procedure:
Warning!
Refer to "Brake Pipe Replacement Warning" in
"Warnings and Notices".
6-40
Hydraulic Brake
Brake System
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст