Geely EC718, EC718RV, EC715, EC715RV. Manual part — 302

FE06-0041b

1.

Install the brake hose to the brake cylinder and tighten the
bolts.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

FE06-0042b

2.

Fix the brake hose.

FE06-0043b

3.

Connect the brake hose and the brake pipe and tighten
the bolt, install the spring.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

4.

Install the wheels.

Note

Refer to "Adding Fluid to the Brake System Notice"
in "Warnings and Notices".

5.

Fill the brake fluid.

6.

Check fluid leak.

Note

Front left and right brake hose replacement is
similar.

Brake System

Hydraulic Brake

6-41

6.4.5.4 Brake Hose Replacement (Rear)

Removal Procedure:

Note

Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice in ""Warnings and Notices".

1

2

FE06-0044b

1.

Drain the brake fluid.

2.

Lift and support the vehicle. Refer to

1.3

Lifting and Jacking

the Vehicle

.

3.

Remove

the

rear

wheels,

taking

into

account

4.4.5.1

Wheel Replacement

.

4.

Remove the bolts, separate the brake pipe and brake
hose (1).

5.

Pull out the spring, pull out brake hose (2) from the
bracket.

FE06-0045b

6.

Remove the bolts, disconnect the the brake hose from the
rear brake slave cylinder.

7.

Remove the rear brake hose.

Installation Procedure:

Warning!

Refer to "Brake Pipe Replacement Warning" in
"Warnings and Notices".

6-42

Hydraulic Brake

Brake System

FE06-0046b

1.

Install the brake hose to the rear brake cylinder and
tighten the bolts.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

FE06-0047b

2.

Connect the brake hoses and the brake pipe and tighten
the bolts, install the spring.

3.

Install the wheels.

Note

Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice" in "Warnings and Notices".

4.

Fill the brake fluid.

5.

Check brake fluid leak.

Note

Rear brake left and right brake hose replacement is
similar.

6.4.5.5 Hydraulic Brake System Exhaust
Procedure

Note

Refer to "Adding Fluid to the Brake System Notice" in
"Warnings and Notices".

Note

Air can not be discharged in hydraulic brake regulator
manually. If the air enters the ABS hydraulic brake
regulator or the installed ABS hydraulic brake adjuster is
not fully filled with fluid, using a scan tool to exhaust
brake system air. The factory ABS hydraulic brake
adjuster is fully filled with fluid, and air is exhausted. In
the normal service regulator procedure, the air will not
enter the ABS hydraulic brake regulator, in this case,
carry out the manual exhaust program.

Brake System

Hydraulic Brake

6-43

Note

If it is not suspected that air enters the master cylinder,
start from step 5. Otherwise, start from step 2.

Note

Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice" in "Warnings and Notices".

FE06-0048b

1.

Shut down the engine, press the brake pedal several
times until the completely eliminate the booster pressure.

2.

Fill the brake fluid to the master cylinder tank. in the
exhaust operations, leave the master cylinder tank fluid
level at least more than half.

3.

Slowly press the brake pedal to the end, and hold the
position.

FE06-0049b

4.

Loosen one brake master cylinder pipe, tighten the
connection when the brake fluid flows out.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

5.

Loosen the other brake master cylinder pipe, tighten the
connection when the brake fluid flows out.

Torque: 16 Nm (Metric) 11.9 lb-ft (US English)

6.

Repeat steps 2 to step 5 three to four times.

FE06-0050b

7.

Remove the air discharge screw dust cover, connect a
transparent tube to the right rear brake caliper air
discharge screw. The tube is immersed in a transparent

6-44

Hydraulic Brake

Brake System