Geely EC718, EC718RV, EC715, EC715RV. Manual part — 297
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 297
6.3.4 Diagnostic Information and Procedures
6.3.4.1 Diagnostic Information and Procedures
For rear brake Diagnostic Information and Procedures, please refer to
Diagnostic Information and Procedures
.
Brake System
Rear Brake
6-21
6.3.5 Removal and Installation
6.3.5.1 Brake Pad Replacement - Rear
Removal Procedure:
Warning!
Refer to "Vehicle Lifting Warning" in "Warnings and
Notices".
Refer to "Brake Dust Warning" in "Warnings and
Notices".
2
1
FE06-0102b
1.
Lift and support the vehicle. Refer to
.
Note
In order to maintain wheel balance, before the tire
removal, mark the wheel to the wheel relative
position.
2.
Remove the rear wheels. Refer to
3.
Disconnect the park brake from the rear caliper. Refer to
Park Brake Control Mechanism Cable Assembly
4.
Remove the rear brake caliper lower assembly bolts (2).
FE06-0103b
5.
Flip the brake caliper upward.
6.
Remove the rear brake pad.
6-22
Rear Brake
Brake System
FE06-0104b
7.
Check the brake pad thickness.
Standard Thickness: 11.0 mm (0.433 in)
Minimum Thickness: 2.0 mm (0.078 in)
If the rear brake pad lining thickness is less than minimum,
replace the rear brake pad.
Note
After replacing with new brake lining block, check
the rear brake disc wear.
Installation Procedure:
FE06-0105b
1.
Check the rear brake pad lining thickness.
Note
Brake caliper piston gap should face the level
direction.
2.
Install the brake pad into the caliper.
1
2
FE06-0106b
3.
Where necessary, use a suitable tool to push the piston.
Note
Carefully pull down the brake caliper assembly and
install the bolts, do not to damage the piston dust
seals.
4.
Pull down the brake caliper and install the assembly bolt
(1).
Torque: 30 Nm (Metric) 22.2 lb-ft (US English)
Note
Refer to "Fastener Notice" in "Warnings and
Notices".
5.
Install the park brake cable (2).
6.
Align the marks made during the wheel removal, install
the rear wheels.
Brake System
Rear Brake
6-23
7.
Lower the vehicle.
Note
Left and right rear brake pad replacement is similar.
6.3.5.2 Brake Caliper Replacement - Rear
Removal Procedure:
Warning!
Refer to "Vehicle Lifting Warning" in "Warnings and
Notices".
Refer to "Brake Fluid Effects on Paint and Electrical
Components Notice" in "Warnings and Notices".
3
2
1
FE06-0107b
1.
Lift and support the vehicle. Refer to
.
Note
In order to maintain wheel balance, before the tire
removal, mark the wheel to the wheel relative
position.
2.
Remove the rear wheels. Refer to
3.
Disconnect the park brake cable from the rear calipers.
Refer to
Park Brake Control Mechanism Cable
.
4.
Remove the brake pad (2). Refer to
.
5.
Remove the brake caliper upper assembly bolts, remove
the brake caliper (3).
FE06-0108b
6.
Remove the brake hose inlet retaining bolts, remove the
brake caliper. Plug the brake caliper inlet and the brake
hose, to prevent the brake fluid loss or contamination.
Note
Rotate to remove the brake caliper, separate the
brake hose inlet bolt from the brake caliper fluid inlet
to prevent damage to the brake hose.
6-24
Rear Brake
Brake System
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст