Geely EC718, EC718RV, EC715, EC715RV. Manual part — 446
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 446
No
Step 7
Diagnostic completed.
11.7.6.8 DTC U150F
DTC
U150F
EEPROM Checksum Error
Diagnostic Steps:
Step 1
Check whether the meter power supply circuit and ground circuit are normal.
Refer to
Yes
Fault site
No
Step 2
Replace the instrument cluster. Refer to
Instrument Cluster Replacement
Next
Step 3
Use scan tool to confirm whether the DTC Code is stored again.
(a)
Connect scan tool to the datalink connector.
(b)
Turn the ignition switch to "ON" position.
(c)
Clear DTC codes.
(d)
Start and run the engine at idle speed to warm up the engine
for at least 5 min.
(e)
Read the control system DTC Code again.
DTC codes still exist?
Yes
No
Step 4
Diagnostic completed.
11.7.6.9 DTC U1400 U1410 U1420 U1430 U1501 U1601
DTC
U1400
ABS Message Time Out, ABS Communication Lost
DTC
U1410
airbag control module Message Time Out, airbag control module Communication Lost
DTC
U1420
BCM Message Time Out, BCM Communication Lost
DTC
U1430
EMS Message Time Out, EMS Communication Lost
DTC
U1501
CAN Network System Integrity Test Failure
DTC
U1601
CAN Bus Off
Diagnostic Steps:
Refer to "Data Communications System" in the
Diagnostic Information and Procedures
.
Body Electric
Instrument / Driver Information System
11-297
11.7.7 Removal and Installation
11.7.7.1 Instrument Cluster Replacement
Removal Procedure
Warning!
Refer to "Battery Disconnect Warning" in "Warnings and
Notices".
0
1
2
3
4
5
6
7
8
0
20
40
60
80
100 120 140
160
180
200
FE11-0510b
1.
Disconnect the battery negative cable. Refer to
.
2.
Adjust the steering wheel to the lowest position, remove
the instrument cluster panel screws.
FE11-0511b
3.
Disconnect the odometer reset switch connector, remove
the instrument cluster panel.
11-298
Instrument / Driver Information System
Body Electric
FE11-0512b
4.
Remove the instrument cluster retaining screw, remove
the instrument cluster.
FE11-0513b
5.
Disconnect the instrument cluster harness connector.
Installation Procedure:
FE11-0514b
1.
Connect the instrument cluster harness connector.
Body Electric
Instrument / Driver Information System
11-299
0
1
2
3
4
5
6
7
8
0
20
40
60
80
100 120
140
160
180
200
FE11-0515b
2.
Install the instrument cluster and tighten the retaining
screws.
Torque: 9.8 Nm (Metric) 7.3 lb-ft (US English)
Note
Refer to "Fastener Notice" in "Warnings and
Notices".
FE11-0516b
3.
Connect the odometer reset switch connector.
0
1
2
3
4
5
6
7
8
0
20
40
60
80
100 120
140
160
180
200
FE11-0517b
4.
Install the instrument cluster panel.
Torque: 3 Nm (Metric) 2.2 lb-ft (US English)
Note
Refer to "Fastener Notice" in "Warnings and
Notices".
5.
Connect the battery negative cable.
11-300
Instrument / Driver Information System
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст