Geely EC718, EC718RV, EC715, EC715RV. Manual part — 449
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 449
3
1
4
2
5 6
Interior Light + Sunroof Switch Harness
Connector RF06
FE11-5703b
(a)
Remove the sunroof switch. Refer to
.
(b)
Measure resistance between the sunroof switch harness
connector RF06 and body ground with a multimeter.
Standard Resistance: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 5
Repair the open circuit between the sunroof switch harness connector RF06 and body ground.
(a)
Confirm the open circuit between the sunroof switch harness
connector RF06 and body ground repair is completed.
Is the sunroof working properly?
Yes
System normal
No
Step 6
Check the sunroof switch assembly.
3
1
4
2
5 6
Interior Light + Sunroof Switch Harness
Connector RF06
FE11-5704b
(a)
Press the sunroof switch, while measure resistance between
the switch RF06 terminals 2,3 and 4 with a multimeter.
(b)
Measure resistance between sunroof switch harness
connector RF06 terminals 4 and body ground with a
multimeter.
Standard Resistance: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 7
Replace the sunroof switch.
(a)
Install a new sunroof switch. Refer to
.
Is the sunroof working properly?
Yes
System normal
Body Electric
Sunroof
11-309
No
Step 8
Check the sunroof assembly harness connector RF08 terminal No.2 and the body ground circuit.
1
4
2
5 6 7 8
3
Sunroof Module Harness Connector RF08
FE11-5705b
(a)
Disconnect the roof harness connector. Refer to
(b)
Measure resistance between the sunroof switch harness
connector RF08 terminal No.2 and the body ground with a
multimeter.
Standard Resistance: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 9
Repair the open circuit between the sunroof assembly harness connector RF08 and body ground.
(a)
Confirm the open circuit between the sunroof assembly
harness connector RF08 and body ground repair is
completed.
Is the sunroof working properly?
Yes
System normal
No
Step 10
Check the sunroof module assembly connector RF08 terminals No.1,3,6 voltage.
1
4
2
5 6 7 8
3
Sunroof Module Harness Connector RF08
FE11-5706b
(a)
Turn the ignition switch to the ON position, measure the
sunroof module assembly connector RF08 terminals No.
1,3,6 voltage with a multimeter.
Standard Voltage: 11-14 V
Yes
No
Step 11
Check the circuits between the sunroof assembly connector RF08 terminal No.1,3,6 and fuses IF-3, IF-25,
IP-8 respectively.
11-310
Sunroof
Body Electric
(a)
Disconnect the roof assembly connector RF08.
(b)
Measure resistance between the sunroof assembly
connector RF08 terminals No.1,3,6, fuse IF-3.IF-25.IP-24
respectively, with a multimeter.
Resistance Standard Value: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 12
Repair the open circuits between the sunroof assembly connector RF08 terminals and fuses IF-3, IF-25,
IP-8.
(a)
Confirm the open circuits between the sunroof assembly
connector RF08 terminals and fuses IF-3, IF-25, IP-8 repair
is completed.
Is the sunroof working properly?
Yes
System normal
No
Step 13
Replace the sunroof motor assembly.
(a)
Replace the sunroof motor assembly. Refer to
Confirm the repair completed.
Next
Step 14
System normal.
11.8.7.5 Sunroof Can Not Open
Schematic:
Diagnostic Steps:
Step 1
Send a ground signal to the sunroof module.
(a)
Remove the sunroof switch. Refer to
.
(b)
Connect the roof antenna switch harness connector RF06
terminal No.3 and body ground with a suitable antenna.
Is the sunroof motor working properly?
Yes
No
Step 2
Check resistance between the sunroof switch and the sunroof module.
(a)
Disconnect the sunroof module harness connector.
Body Electric
Sunroof
11-311
(b)
Measure resistance between the sunroof module harness
connector terminal No.5 and sunroof switch wiring harness
connector RF08 terminal No.3 with a multimeter.
Resistance Standard Value: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 3
Repair the wiring harness between the sunroof switch and the sunroof module assembly.
Is the sunroof working properly?
Yes
System normal
No
Step 4
Replace the sunroof motor.
(a)
Replace the sunroof motor. Refer to
Confirm the repair completed.
Yes
System normal
No
Step 5
Check the circuit between the sunroof switch harness connector RF06 and body ground.
(a)
Remove the sunroof switch. Refer to
.
(b)
Measure resistance between the sunroof switch harness
connector RF06 terminal No.4 and body ground with a
multimeter.
Standard Resistance: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 6
Repair the circuit between the sunroof switch harness connector RF06 and body ground.
Confirm the repair completed.
Yes
System normal
No
Step 7
Replace the sunroof switch assembly.
(a)
Install a new sunroof switch. Refer to
.
Confirm the repair completed.
11-312
Sunroof
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст