SCANIA INDUSTRIAL ENGINES (specification) — part 6
SCANIA industrial engines
dC13 080a. 264 kW (360 hp)
us tier 4i, eu stage iiiB
Standard equipment
• Scania Engine Management System, EMS
• Extra high pressure fuel injection system, XPI
• Turbocharger
• Fuel filter and extra pre-filter with water
separator
• Fuel heater
• Oil filter, full flow
• Centrifugal oil cleaner
• Oil cooler, integrated in block
• Oil filler, in valve cover
• Deep front oil sump
• Oil dipstick, in block
• Magnetic drain plug for oil draining
• Starter, 1-pole 6.0 kW
• Alternator, 1-pole 100A
• Flywheel, for use with friction clutch
• Silumin flywheel housing, SAE 1 flange
• Front-mounted engine brackets
• SCR system
• Open crankcase ventilation
• Operator’s manual
Optional equipment
• Cooling package
• Puller and pusher fans
• Fan ring with sealing
• Hydraulic pump
• Air compressor
• AC compressor
• Side-mounted PTO
• Front-mounted PTO
• Exhaust connections
• Electrical base system
• Control and instrument panels
• Accelerator position sensor
• Engine heater
• Flywheels: SAE11.5”, SAE14”, DANA15/16”,
ZF WG260
• Stiff rubber engine suspension
• Air cleaner
• Closed crankcase ventilation
• Studs in flywheel housing
• External thermostat for extra oil cooler
• Low coolant level reaction
• Variable idle speed setting
• Low oil sump
• Oil level sensor
The industrial engines from Scania are based on a robust design with a strength
optimised cylinder block containing wet cylinder liners that can easily be exchanged.
Individual cylinder heads with 4 valves per cylinder promotes repairability and fuel
economy.
The engine is equipped with a Scania developed Engine Management System,
EMS, in order to ensure the control of all aspects related to engine performance.
The injection system is Scania’s XPI (Extra High Pressure Injection), a common rail
system that in combination with SCR (Selective Catalytic Reduction) gives low exhaust
emissions with good fuel economy and a high torque. The engine can be fitted with
many accessories such as air cleaners, silencers, PTOs and flywheels in order to suit
a variety of installations.
This specification may be revised without notice.
Engine speed (rpm)
Rating
1200
1500
1800
Gross power (kW)
ICFN
191
231
264
Gross power (hp, metric)
ICFN
260
314
360
Gross torque (Nm)
ICFN
1521
1471
1403
Spec fuel consumption. Full load (g/kWh)
189
190
199
Spec fuel consumption. 3/4 load (g/kWh)
189
189
200
Spec fuel consumption. 1/2 load (g/kWh)
194
195
203
Reductant consumption. Full load (g/kWh)
18
13
12
Heat rejection to coolant (kW)
79
81
85
ICFN – Continuous service: Rated output available 1/1 h.
Unlimited h/year service time at a load factor of 100%
SCANIA industrial engines
se 151 87 södertälje, sweden
telephone +46 8 553 810 00
telefax +46 8 553 829 93
www.scania.com
engines@scania.com
dC13 080a. 264 kW (360 hp)
us tier 4i, eu stage iiiB
edition 01 ©
scania CV
a
B,
se
-151 87
södertälje,
sweden
190
210
230
250
270
290
310
330
350
370
140
150
160
170
180
190
200
210
220
230
240
250
260
270
hp
kW
140
150
160
1370
1470
1570
kpm
Nm
0
10
20
30
40
50
60
70
80
90
100
180
185
190
195
200
1000
1200
1400
1600
1800
g/kWh
Reductant
g/kWh
Fuel
rpm
Reductant
Fuel
190
210
230
250
270
290
310
330
350
370
140
150
160
170
180
190
200
210
220
230
240
250
260
270
hp
kW
140
150
160
1370
1470
1570
kpm
Nm
0
10
20
30
40
50
60
70
80
90
100
180
185
190
195
200
1000
1200
1400
1600
1800
g/kWh
Reductant
g/kWh
Fuel
rpm
Reductant
Fuel
190
210
230
250
270
290
310
330
350
370
140
150
160
170
180
190
200
210
220
230
240
250
260
270
hp
kW
140
150
160
1370
1470
1570
kpm
Nm
0
10
20
30
40
50
60
70
80
90
100
180
185
190
195
200
1000
1200
1400
1600
1800
g/kWh
Reductant
g/kWh
Fuel
rpm
Reductant
Fuel
Output
Torque
Spec fuel and Reductant consumption
Engine description
No of cylinders
6 in-line
Working principle
4-stroke
Firing order
1 - 5 - 3 - 6 - 2 - 4
Displacement
12.7 litres
Bore x stroke
130 x 160 mm
Compression ratio
17.3:1
Weight
1050 kg (excl oil and coolant)
Piston speed at 1500 rpm
8.0 m/s
Piston speed at 1800 rpm
9.6 m/s
Camshaft
High position alloy steel
Pistons
Steel pistons
Connection rods
I-section press forgings of alloy steel
Crankshaft
Alloy steel with hardened
and polished bearing surfaces
Oil capacity
34-45 dm
3
Electrical system
1-pole 24V
1406
442
447
674
434
Test conditions Air temperature +25°C. Barometric pressure 100 kPa (750 mmHg). Humidity 30%. Diesel fuel
acc. to ECE R 24 Annex 6. Density of fuel 0.840 kg/dm
3
.
Viscosity of fuel 3.0 cSt at 40°C. Energy value 42700 kJ/kg.
Power test code ISO 3046. Power and fuel values +/-3%.
1:6969
1:6970
all dimensions in mm
SCANIA industrial engines
sCr system
us tier 4i, eu stage iiiB
SCR (Selective Catalytic Reduction) technology is used on Scania’s engines
for Stage IIIB and Tier 4i to reduce the NO
X
content in the exhaust gases.
A chemical process is started by injecting reductant, a urea and water
mixture, into the exhaust gas stream. During injection the water evaporates
and the urea breaks down to form ammonia. The ammonia then reacts
with the nitrogen gases in the catalytic converter and forms harmless
products such as nitrogen gas and water. Through the use of SCR the
exhaust gases are purged of poisonous levels of NO
X
in the best possible
way. Scania is making use of a system that is carefully developed and
tested in our own laboratory.
The reductant tank holds 38 or 60 litres and is heated by the engine’s
cooling system in order to avoid freezing of the urea solution, urea
freezes at -11°C. The reductant tank and a pump module are delivered
as a unit which is fi tted to brackets for an easy installation. The Scania
system contains all mechanical and electrical parts needed except from
the exhaust piping which is to be adapted according to the customers
installation.
Mechanical system
Standard
Optional
1
Reductant tank and pump module
38 l
60 l
2
Reductant fl uid return line
2 m
3.5 m
3
Coolant valve
–
4
Reductant pressure line
2 m
3.5 m
5
Coolant hose for tank and pump
heating
–
–
6
Evaporator module / Hydrolysis
catalyst with reductant doser
–
7
NO
X
sensor with control unit
–
8
SCR catalyst
–
9
Temperature sensor
–
10
Coolant hose, return from tank and
pump heating
–
–
Mechanical system
Electric system
Electric system
Standard
Optional
1
Customer interface, SCR system
–
2
Pipe network between engine and
SCR control unit
3 m
6 m
3
Electrical interface, SCR system
–
4
Temperature sensor electrical cable
3 m
6 m, 9 m
5
Reductant doser electrical cable
3 m
6 m
6
NO
X
sensor electrical cable
3 m
6 m
The principle for Scania SCR system
This specifi cation may be revised without notice.
6
1
9
2
8
3
7
5
10
4
1:7058
3
1
2
6
5
4
1:7059
SCANIA industrial engines
se 151 87 södertälje, sweden
telephone +46 8 553 810 00
telefax +46 8 553 829 93
www.scania.com
engines@scania.com
sCr system
us tier 4i, eu stage iiiB
edition 04 ©
scania CV
a
B,
se
-151 87
södertälje,
sweden
Engine
Power (kw)
Volume (litres) Measure A (mm)
DC09
202-294
24
765
DC13
257-405
33
857
DC16
405-515
48
1060
SCR catalyst
Hydrolysis catalyst (DC16)
with reductant doser
720
280
85
21
1:7060
575
725
280
85
14
705
1:7061
466
Ø185
Ø190
1:7062
Reductant tank - 38 litres
Total volume: 50 litres
Filling volume: 38 litres
Reductant tank - 60 litres
Total volume: 75 litres
Filling volume: 60 litres
This specification may be revised without notice.
Evaporator module (DC09, DC13)
with reductant doser
SCANIA industrial engines
dC13 081a. 257 kW (350 hp)
eu stage iiiB
Standard equipment
• Scania Engine Management System, EMS
• Extra high pressure fuel injection system, XPI
• Turbocharger
• Fuel filter and extra pre-filter with water
separator
• Fuel heater
• Oil filter, full flow
• Centrifugal oil cleaner
• Oil cooler, integrated in block
• Oil filler, in valve cover
• Deep front oil sump
• Oil dipstick, in block
• Magnetic drain plug for oil draining
• Starter, 1-pole 6.0 kW
• Alternator, 1-pole 100A
• Flywheel, for use with friction clutch
• Silumin flywheel housing, SAE 1 flange
• Front-mounted engine brackets
• SCR system
• Open crankcase ventilation
• Operator’s manual
Optional equipment
• Cooling package
• Puller and pusher fans
• Fan ring with sealing
• Hydraulic pump
• Air compressor
• AC compressor
• Side-mounted PTO
• Front-mounted PTO
• Exhaust connections
• Electrical base system
• Control and instrument panels
• Accelerator position sensor
• Engine heater
• Flywheels: SAE11.5”, SAE14”, DANA15/16”,
ZF WG260
• Stiff rubber engine suspension
• Air cleaner
• Closed crankcase ventilation
• Studs in flywheel housing
• External thermostat for extra oil cooler
• Low coolant level reaction
• Variable idle speed setting
• Low oil sump
• Oil level sensor
The industrial engines from Scania are based on a robust design with a strength
optimised cylinder block containing wet cylinder liners that can easily be exchanged.
Individual cylinder heads with 4 valves per cylinder promotes repairability and fuel
economy.
The engine is equipped with a Scania developed Engine Management System,
EMS, in order to ensure the control of all aspects related to engine performance.
The injection system is Scania’s XPI (Extra High Pressure Injection), a common rail
system that in combination with SCR (Selective Catalytic Reduction) gives low exhaust
emissions with good fuel economy and a high torque. The engine can be fitted with
many accessories such as air cleaners, silencers, PTOs and flywheels in order to suit
a variety of installations.
This specification may be revised without notice.
Engine speed (rpm)
Rating
1200
1500
1800
2100
Gross power (kW)
ICFN
245
257
257
257
Gross power (hp, metric)
ICFN
333
350
350
350
Gross torque (Nm)
ICFN
1950
1636
1363
1169
Spec fuel consumption. Full load (g/kWh)
181
184
196
205
Spec fuel consumption. 3/4 load (g/kWh)
182
185
198
211
Spec fuel consumption. 1/2 load (g/kWh)
188
194
210
225
Reductant consumption. Full load (g/kWh)
25
18
15
17
Heat rejection to coolant (kW)
88
83
87
94
ICFN – Continuous service: Rated output available 1/1 h.
Unlimited h/year service time at a load factor of 100%
SCANIA industrial engines
se 151 87 södertälje, sweden
telephone +46 8 553 810 00
telefax +46 8 553 829 93
www.scania.com
engines@scania.com
dC13 081a. 257 kW (350 hp)
eu stage iiiB
edition 01 ©
scania CV
a
B,
se
-151 87
södertälje,
sweden
230
240
250
260
270
280
290
300
310
320
330
340
350
360
170
175
180
185
190
195
200
205
210
215
220
225
230
235
240
245
250
255
260
265
hp
kW
180
190
200
1780
1880
1980
kpm
Nm
110
120
130
140
150
160
170
180
190
1080
1180
1280
1380
1480
1580
1680
1780
1880
0
10
20
30
40
50
60
70
80
90
100
165
170
175
180
185
190
195
200
205
210
1000
1200
1400
1600
1800
2000
g/kWh
Reductant
g/kWh
Fuel
rpm
Reductant
Fuel
230
240
250
260
270
280
290
300
310
320
330
340
350
360
170
175
180
185
190
195
200
205
210
215
220
225
230
235
240
245
250
255
260
265
hp
kW
180
190
200
1780
1880
1980
kpm
Nm
110
120
130
140
150
160
170
180
190
1080
1180
1280
1380
1480
1580
1680
1780
1880
0
10
20
30
40
50
60
70
80
90
100
165
170
175
180
185
190
195
200
205
210
1000
1200
1400
1600
1800
2000
g/kWh
Reductant
g/kWh
Fuel
rpm
Reductant
Fuel
230
240
250
260
270
280
290
300
310
320
330
340
350
360
170
175
180
185
190
195
200
205
210
215
220
225
230
235
240
245
250
255
260
265
hp
kW
180
190
200
1780
1880
1980
kpm
Nm
110
120
130
140
150
160
170
180
190
1080
1180
1280
1380
1480
1580
1680
1780
1880
0
10
20
30
40
50
60
70
80
90
100
165
170
175
180
185
190
195
200
205
210
1000
1200
1400
1600
1800
2000
g/kWh
Reductant
g/kWh
Fuel
rpm
Reductant
Fuel
Output
Torque
Spec fuel and Reductant consumption
Engine description
No of cylinders
6 in-line
Working principle
4-stroke
Firing order
1 - 5 - 3 - 6 - 2 - 4
Displacement
12.7 litres
Bore x stroke
130 x 160 mm
Compression ratio
17.3:1
Weight
1050 kg (excl oil and coolant)
Piston speed at 1500 rpm
8.0 m/s
Piston speed at 1800 rpm
9.6 m/s
Camshaft
High position alloy steel
Pistons
Steel pistons
Connection rods
I-section press forgings of alloy steel
Crankshaft
Alloy steel with hardened
and polished bearing surfaces
Oil capacity
34-45 dm
3
Electrical system
1-pole 24V
1406
442
447
674
434
Test conditions Air temperature +25°C. Barometric pressure 100 kPa (750 mmHg). Humidity 30%. Diesel fuel
acc. to ECE R 24 Annex 6. Density of fuel 0.840 kg/dm
3
.
Viscosity of fuel 3.0 cSt at 40°C. Energy value 42700 kJ/kg.
Power test code ISO 3046. Power and fuel values +/-3%.
1:6969
1:6970
all dimensions in mm
SCANIA industrial engines
sCr system
eu stage iiiB
SCR (Selective Catalytic Reduction) technology is used on Scania’s engines
for Stage IIIB and Tier 4i to reduce the NO
X
content in the exhaust gases.
A chemical process is started by injecting reductant, a urea and water
mixture, into the exhaust gas stream. During injection the water evaporates
and the urea breaks down to form ammonia. The ammonia then reacts
with the nitrogen gases in the catalytic converter and forms harmless
products such as nitrogen gas and water. Through the use of SCR the
exhaust gases are purged of poisonous levels of NO
X
in the best possible
way. Scania is making use of a system that is carefully developed and
tested in our own laboratory.
The reductant tank holds 38 or 60 litres and is heated by the engine’s
cooling system in order to avoid freezing of the urea solution, urea
freezes at -11°C. The reductant tank and a pump module are delivered
as a unit which is fi tted to brackets for an easy installation. The Scania
system contains all mechanical and electrical parts needed except from
the exhaust piping which is to be adapted according to the customers
installation.
Mechanical system
Standard
Optional
1
Reductant tank and pump module
38 l
60 l
2
Reductant fl uid return line
2 m
3.5 m
3
Coolant valve
–
4
Reductant pressure line
2 m
3.5 m
5
Coolant hose for tank and pump
heating
–
–
6
Evaporator module / Hydrolysis
catalyst with reductant doser
–
7
NO
X
sensor with control unit
–
8
SCR catalyst
–
9
Temperature sensor
–
10
Coolant hose, return from tank and
pump heating
–
–
Mechanical system
Electric system
Electric system
Standard
Optional
1
Customer interface, SCR system
–
2
Pipe network between engine and
SCR control unit
3 m
6 m
3
Electrical interface, SCR system
–
4
Temperature sensor electrical cable
3 m
6 m, 9 m
5
Reductant doser electrical cable
3 m
6 m
6
NO
X
sensor electrical cable
3 m
6 m
The principle for Scania SCR system
This specifi cation may be revised without notice.
6
1
9
2
8
3
7
5
10
4
1:7058
3
1
2
6
5
4
1:7059
SCANIA industrial engines
se 151 87 södertälje, sweden
telephone +46 8 553 810 00
telefax +46 8 553 829 93
www.scania.com
engines@scania.com
sCr system
eu stage iiiB
edition 04 ©
scania CV
a
B,
se
-151 87
södertälje,
sweden
Engine
Power (kw)
Volume (litres) Measure A (mm)
DC09
202-294
24
765
DC13
257-405
33
857
DC16
405-515
48
1060
SCR catalyst
Hydrolysis catalyst (DC16)
with reductant doser
720
280
85
21
1:7060
575
725
280
85
14
705
1:7061
466
Ø185
Ø190
1:7062
Reductant tank - 38 litres
Total volume: 50 litres
Filling volume: 38 litres
Reductant tank - 60 litres
Total volume: 75 litres
Filling volume: 60 litres
This specification may be revised without notice.
Evaporator module (DC09, DC13)
with reductant doser
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст