Lexus LC500 (2022 year). Manual in english — page 10
179
4
4-2. Driving procedures
Dr
ivin
g
Make sure to check that the buzzer sounds
and “Holding N Push P Switch When
Done” is displayed on the multi-informa-
tion display.
To change to a shift position other
than N, press the P position switch.
The shift position will be changed to
P.
Even if the hybrid system is not
operating, by operating the shift
lever and the power switch, the
power switch may be changed to
ACCESSORY mode with the shift
position held in N. Make sure that
the hybrid system is operating
before performing the operation.
*
: To keep this state, do not operate the
power switch. If the power switch is
operated repeatedly, the power switch
will turn off after the shift position has
automatically changed to P.
Q
Driving mode
P.238
Q
Snow mode
Snow mode can be selected to suit the
conditions when driving on slippery
road surfaces, such as on snow.
Turn the
switch backward.
The snow mode indicator comes on.
Turn the
switch backward again to
return to normal mode.
Q
Snow mode automatic deactivation
Snow mode is automatically deactivated if
the power switch is turned off after driving
in snow mode.
To drive using temporary shift range
selection, operate the “-” or “+” paddle
shift switch.
When the “-” paddle shift switch is
operated, the shift range switches to a
range that enables engine braking
force that is suitable to driving condi-
tions. When the “+” paddle shift switch
is operated, the shift range switches to
a range that is one range higher than
the current range.
Changing the shift range allows
restriction of the highest shift range,
preventing unnecessary upshifting and
NOTICE
Q
Keeping the shift position in N when
changing to ACCESSORY mode
When you wish to keep the shift position
in N when changing the power switch to
ACCESSORY mode, make sure that
the hybrid system is operating before
operating the power switch.
If the power switch mode is changed
without the hybrid system is operating,
the shift position may change to P.
Selecting the driving mode
Selecting shift ranges in the D
position
180
4-2. Driving procedures
enabling the level of engine braking
force to be selected.
1
Upshifting
2
Downshifting
The selected shift range, from D1 to D10,
will be displayed in the meter.
To return to normal D position driving, the
“+” paddle shift switch must be held down
for a period of time.
A lower shift range will provide greater
engine braking forces than a higher shift
range.
Q
Automatic deactivation of shift range
selection in the D position
Shift range selection in the D position will
be deactivated in the following situations:
O
When the vehicle comes to a stop
O
If the accelerator pedal is depressed for
more than a certain period of time
O
When the shift lever is moved to D again
O
When the “+” paddle shift switch is
pressed and held
O
When dynamic radar cruise control with
full-speed range or cruise control is
operating
Q
Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some-
times be restricted. In some circumstances,
downshifting may not be possible even
when the paddle shift switch is operated. (A
buzzer will sound twice.)
To enter M mode, shift the shift posi-
tion to M. Gears can be selected by
operating the paddle shift switches,
allowing you to drive in the gear of
your choosing.
1
Upshifting
2
Downshifting
The gear changes once every time the
paddle shift switch is operated.
The selected gear, from M1 to M10, will be
fixed and displayed in the meter.
When in the M position, the gear will
not change unless the paddle shift
switches are operated.
However, even when in the M position,
the gears will be automatically
changed in the following situation:
Meter dis-
play
Function
D2 - D10
A gear in the range between
D1 and the selected shift
range is automatically cho-
sen depending on vehicle
speed and driving conditions
D1
Setting the shift range at D1
Selecting gears in the M position
181
4
4-2. Driving procedures
Dr
ivin
g
When vehicle speed drops (down-
shift only).
When vehicle speed increases
(upshift only).
When the accelerator pedal is firmly
depressed.
When it is necessary to protect the
transmission when the transmission
fluid temperature is high or low, or
other reasons.
When particulate matter has accu-
mulated in the exhaust filter.
Also, the gear will not shift when the
vehicle speed is low, even if an upshift
operation is performed.
Q
Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some-
times be restricted. In some circumstances,
downshifting may not be possible even
when the paddle shift switch is operated. (A
buzzer will sound twice.)
The Gear Shift Indicator display is a
guide to help the driver achieve
improved fuel economy and reduced
exhaust emissions within limits of
engine performance.
When not in operation
Shift-up indicator
Q
Gear Shift Indicator function
This function automatically operates
during M mode.
By following the Shift-up indicator
and shifting up accordingly, it is pos-
sible to achieve improved fuel econ-
omy and reduced exhaust
emissions.
The Gear Shift Indicator does not
have a similar function for down-
shifting.
Depending on the driving condi-
tions, the Gear Shift Indicator may
not display the Shift-up indicator
while driving in M mode.
Gear Shift Indicator
WARNING
Q
Gear Shift Indicator display
For safety, the driver should not look only
at the display. Refer to the display when it
is safe to do so while considering actual
traffic and road conditions.
Failure to do so may lead to an accident.
A
B
182
4-2. Driving procedures
1
Right turn
2
Lane change to the right (move the
lever partway and release it)
The right hand signals will flash 3 times.
3
Lane change to the left (move the
lever partway and release it)
The left hand signals will flash 3 times.
4
Left turn
Q
Turn signals can be operated when
The engine switch <power switch> is in
IGNITION ON mode <ON mode>.
Q
If the indicator flashes faster than usual
Check that a light bulb in the front or rear
turn signal lights has not burned out.
Q
If the turn signals stop flashing before a
lane change has been performed
Operate the lever again.
Q
Customization
P.425
Turn signal lever
Operating instructions
183
4
4-2. Driving procedures
Dr
ivin
g
Q
Using the manual mode
The parking brake can be set and
released manually.
1
Push the switch to set the parking
brake
The parking brake indicator light will turn
on.
Press and hold the parking brake switch if
an emergency occurs and it is necessary to
operate the parking brake while driving.
2
Pull the switch to release the park-
ing brake
• Operate the parking brake switch while
depressing the brake pedal.
• Using the parking brake automatic
release function, the parking brake can
be released by depressing the accelera-
tor pedal. When using this function,
slowly depress the accelerator pedal.
Make sure that the parking brake indicator
light turn off.
Q
Turning the automatic mode on
While the vehicle is stopped, press and
hold the parking brake switch until a
message is shown on the multi-infor-
mation display
When the automatic mode is turned
on, the parking brake operates as fol-
lows.
When the shift position is shifted
from P, the parking brake will be
released, and the parking brake
indicator light will turn off.
When the shift position is shifted to
P, the parking brake will be set, and
the parking brake indicator light will
turn on.
Operate the shift lever and P position
switch with the vehicle stopped and the
brake pedal depressed.
Parking brake
The parking brake can be set or
released automatically or manually.
In automatic mode, the parking
brake can be set or released auto-
matically according to shift lever
operation. Also, even in automatic
mode, the parking brake can be set
or released manually.
Operating instructions
184
4-2. Driving procedures
Q
Turning the automatic mode off
While the vehicle is stopped, pull and
hold the parking brake switch until a
message is shown on the multi-infor-
mation display
Q
Parking brake operation
O
When the engine switch <power switch>
is not in IGNITION ON mode <ON
mode>, the parking brake cannot be
released using the parking brake switch.
O
When the engine switch <power switch>
is not in IGNITION ON mode <ON
mode>, automatic mode (automatic
brake setting and releasing) is not avail-
able.
Q
Parking brake automatic release func-
tion
O
When the shift position is shifted from P,
the parking brake will be released in
automatic mode.
O
When all of the following conditions are
met in manual mode, the parking brake
can be released by depressing the accel-
erator pedal.
• The driver’s door is closed
• The driver is wearing the seat belt
• The shift position is in D, M or R
Q
If “EPB frequently operated Wait a min-
ute” is displayed on the multi-informa-
tion display
If the parking brake is operated repeatedly
over a short period of time, the system may
restrict operation to prevent overheating. If
this happens, refrain from operating the
parking brake. Normal operation will return
after about 1 minute.
Q
If “EPB Activation Stopped Incom-
pletely” or “EPB unavailable” is dis-
played on the multi-information display
Operate the parking brake switch. If the
message does not disappear after operat-
ing the switch several times, the system may
be malfunctioning. Have the vehicle
inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reli-
able repairer.
Q
Parking brake operation sound
When the parking brake operates, a motor
sound (whirring sound) may be heard. This
does not indicate a malfunction.
Q
Parking brake indicator light
O
Depending on the engine switch <power
switch> mode, the parking brake indica-
tor light will turn on and stay on as
described below:
IGNITION ON mode <ON mode>:
Comes on until the parking brake is
released.
Not in IGNITION ON mode <ON
mode>: Stays on for approximately 15
seconds.
O
When the engine switch <power switch>
is turned off with the parking brake set,
the parking brake indicator light will stay
on for about 15 seconds. This does not
indicate a malfunction.
Q
When the parking brake switch mal-
functions
Automatic mode (automatic brake setting
and releasing) will be turned on automati-
cally.
Q
Parking the vehicle
P.148
Q
Parking brake engaged warning buzzer
A buzzer will sound if the vehicle is driven
with the parking brake engaged. “EPB
applied” is displayed on the multi-informa-
tion display (with the vehicle reached a
speed of 5 km/h [3 mph]).
185
4
4-2. Driving procedures
Dr
ivin
g
Q
If the brake system warning light comes
on
P.371
Q
Usage in winter time
P.269
Turns the brake hold system on
The brake hold standby indicator
(green) comes on. While the system is
holding the brake, the brake hold operated
indicator
(yellow) comes on.
Q
Brake hold system operating conditions
The brake hold system cannot be turned on
in the following conditions:
O
The driver’s door is not closed.
O
The driver is not wearing the seat belt.
O
“EPB Activation Stopped Incompletely”
or “EPB Malfunction Visit your dealer” is
displayed on the multi-information dis-
play.
If any of the conditions above are detected
when the brake hold system is enabled, the
WARNING
Q
When parking the vehicle
Do not leave a child in the vehicle alone.
The parking brake may be released unin-
tentionally and there is the danger of the
vehicle moving that may lead to an acci-
dent resulting in death or serious injury.
NOTICE
Q
When parking the vehicle
Before you leave the vehicle, shift the
shift position to P, set the parking brake
and make sure that the vehicle does not
move.
Q
When the system malfunctions
Stop the vehicle in a safe place and
check the warning messages.
Q
When the parking brake cannot be
released due to a malfunction
Driving the vehicle with the parking
brake set will lead to brake components
overheating, which may affect braking
performance and increase brake wear.
Have the vehicle inspected by any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi-
ately if this occurs.
Brake Hold
The brake hold system keeps the
brake applied when the shift posi-
tion is in D, M or N with the system
on and the brake pedal has been
depressed to stop the vehicle. The
system releases the brake when the
accelerator pedal is depressed with
the shift position in D or M to allow
smooth start off.
Enabling the system
A
B
186
4-2. Driving procedures
system will turn off and the brake hold
standby indicator light will go off. In addi-
tion, if any of the conditions are detected
while the system is holding the brake, a
warning buzzer will sound and a message
will be shown on the multi-information dis-
play. The parking brake will then be set
automatically.
Q
Brake hold function
O
If the brake pedal is left released for a
period of about 3 minutes after the sys-
tem has started holding the brake, the
parking brake will be set automatically. In
this case, a warning buzzer sounds and a
message is shown on the multi-informa-
tion display.
O
To turn the system off while the system is
holding the brake, firmly depress the
brake pedal and press the button again.
O
The brake hold function may not hold the
vehicle when the vehicle is on a steep
incline. In this situation, it may be neces-
sary for the driver to apply the brakes. A
warning buzzer will sound and the multi-
information display will inform the driver
of this situation. If a warning message is
shown on the multi-information display,
read the message and follow the instruc-
tions.
Q
When the parking brake is set automati-
cally while the system is holding the
brakes
Perform any of the following operations to
release the parking brake.
O
Depress the accelerator pedal. (The
parking brake will not be released auto-
matically if the seat belt is not fastened.)
O
Operate the parking brake switch with
the brake pedal depressed.
Make sure that the parking brake indicator
light goes off. (
P.183)
Q
When an inspection at any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer is nec-
essary
When the brake hold standby indicator
(green) does not illuminate even when the
brake hold switch is pressed with the brake
hold system operating conditions met, the
system may be malfunctioning. Have the
vehicle inspected at any authorized Lexus
retailer or Lexus authorized repairer, or any
reliable repairer.
Q
If “Brake Hold Fault Depress Brake to
Deactivate Visit Your Dealer” or
“Brake Hold Malfunction Visit Your
Dealer” is displayed on the multi-infor-
mation display
The system may be malfunctioning. Have
the vehicle inspected by any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer.
Q
Warning message and buzzers
Warning messages and buzzers are used to
indicate a system malfunction or to inform
the driver of the need for caution. If a warn-
ing message is shown on the multi-informa-
tion display, read the message and follow
the instructions.
Q
If the brake hold operated indicator
flashes
P.375
WARNING
Q
When the vehicle is on a steep incline
When using the brake hold system on a
steep incline exercise caution. The brake
hold function may not hold the vehicle in
such a situation.
Q
When stopped on a slippery road
The system cannot stop the vehicle when
the gripping ability of the tires has been
exceeded. Do not use the system when
stopped on a slippery road.
187
4
4-2. Driving procedures
Dr
ivin
g
NOTICE
Q
When parking the vehicle
The brake hold system is not designed
for use when parking the vehicle for a
long period of time. Turning the engine
switch <power switch> off while the sys-
tem is holding the brake may release the
brake, which would cause the vehicle to
move. When operating the engine switch
<power switch>, depress the brake pedal,
shift the shift position to P and set the
parking brake.
188
4-3. Operating the lights and wipers
4-3.Operating the lights and wipers
Operating the
switch turns on
the lights as follows:
1
The front position, tail, license
plate and instrument panel lights
turn on.
2
The headlights and all the
lights listed above turn on.
3
The headlights, daytime run-
ning lights (
P.188) and all the
lights listed above turn on and off
automatically.
Q
AUTO mode can be used when
The engine switch <power switch> is in
IGNITION ON mode <ON mode>.
Q
Daytime running light function
To make your vehicle more visible to other
drivers during daytime driving, the daytime
running lights turn on automatically when-
ever the engine <hybrid system> is started
and the parking brake is released with the
headlight switch in the
position. (Illumi-
nate brighter than the front position lights.)
Daytime running lights are not designed for
use at night.
Q
Headlight control sensor
The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detect-
ing the level of ambient light and may cause
the automatic headlight system to malfunc-
tion.
Q
Automatic light off system
O
When the light switch is in
: The
headlights turn off automatically if the
engine switch <power switch> is turned to
ACCESSORY mode or turned off.
O
When the light switch is in
: The
headlights and all the lights turn off auto-
matically if the engine switch <power
switch> is turned to ACCESSORY mode
or turned off.
To turn the lights on again, turn the engine
switch <power switch> to IGNITION ON
mode <ON mode>, or turn the light switch
Headlight switch
The headlights can be operated
manually or automatically.
Turning on the headlights
189
4
4-3. Operating the lights and wipers
Dr
ivin
g
to
position once and then back to
or .
Q
Light reminder buzzer
A buzzer sounds when the engine switch
<power switch> is turned off or turned to
ACCESSORY mode and the driver’s door
is opened while the lights are turned on.
Q
Automatic headlight leveling system
The level of the headlights is automatically
adjusted according to the number of pas-
sengers and the loading condition of the
vehicle to ensure that the headlights do not
interfere with other road users.
Q
12-volt battery-saving function
In order to prevent 12-volt the battery of the
vehicle from discharging, if the light switch
is in the
or
position when the
engine switch <power switch> is turned off
the 12-volt battery saving function will oper-
ate and automatically turn off all the lights
after approximately 20 minutes.
When the engine switch <power switch> is
turned to IGNITION ON mode <ON
mode>, the 12-volt battery-saving function
will be disabled.
When any of the following are performed,
the 12-volt battery-saving function is can-
celed once and then reactivated. All the
lights will turn off automatically 20 minutes
after the 12-volt battery- saving function has
been reactivated:
O
When the headlight switch is operated
O
When a door is opened or closed
Q
Welcome light illumination control
The front position, tail lights and license
plate lights automatically turn on at night
when the doors are unlocked using the
entry function or wireless remote control if
the light switch is in the
position.
Q
Customization
Settings (e.g. light sensor sensitivity) can be
changed.
(Customizable features:
P.425)
1
With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2
Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with the
headlights on or off.
This system allows the headlights and
front position lights to be turned on for
30 seconds when the engine switch
<power switch> is off.
Pull the lever toward you and release it
NOTICE
Q
To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the engine is not running
<hybrid system is not operating>.
Turning on the high beam head-
lights
Extended Headlight Lighting
system
190
4-3. Operating the lights and wipers
with the light switch is in
after turn-
ing the engine switch <power switch>
off.
Pull the lever toward you and release it
again to turn off the lights.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
The steering wheel is operated
The turn signal lever is operated
The shift position is in R (both left
and right side cornering lights)
Q
Cornering light control
O
The lights illuminate when the vehicle
speed is approximately 30 km/h (19
mph) or less. However, the lights turn off
when the vehicle speed increases to
approximately 35 km/h (22 mph) or
more.
O
After the lights remain illuminated for 30
minutes, they automatically turn off.
*
: If equipped
1
Press the Automatic High Beam
switch.
2
Turn the headlight switch to the
or
position.
Cornering lights
AHB (Automatic High
Beam)
*
The Automatic High Beam uses an
in-vehicle front camera to assess
the brightness of streetlights, the
lights of a vehicle ahead, etc., and
automatically turns the high beam
on or off as necessary.
WARNING
Q
Limitations of the Automatic High
Beam
Do not rely on the Automatic High
Beam. Always drive safely, taking care to
observe your surroundings and turning
the high beam on or off manually if nec-
essary.
Q
To prevent incorrect operation of the
Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam system
191
4
4-3. Operating the lights and wipers
Dr
ivin
g
The AHB indicator will come on when the
system is operating.
Q
High beam automatic turning on or off
conditions
O
When all of the following conditions are
met, the high beam will be automatically
turned on (after approximately 1 second):
• Vehicle speed is above approximately
30 - 40 km/h (19 - 25 mph)
*
.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with head-
lights or tail lights turned on.
• There are few streetlights on the road
ahead.
O
If any of the following conditions are met,
the high beam will be automatically
turned off:
• Vehicle speed drops below approxi-
mately 25 - 30 km/h (16 - 19 mph)
*
.
• The area ahead of the vehicle is not dark.
• Vehicles ahead have headlights or tail
lights turned on.
• There are many streetlights on the road
ahead.
*
: The vehicle speed at which the high
beams are automatically turned on/off
may vary depending on the country for
which the vehicle is approved.
Q
Front camera detection information
O
The high beam may not be automatically
turned off in the following situations:
• When oncoming vehicles suddenly
appear from a curve
• When the vehicle is cut in front of by
another vehicle
• When vehicles ahead are hidden from
sight due to repeated curves, road divid-
ers or roadside trees
• When vehicles ahead appear from the
faraway lane on wide road
• When vehicles ahead have no lights
O
The high beam may be turned off if a
vehicle ahead that is using fog lights with-
out using the headlights is detected.
O
House lights, street lights, traffic signals,
and illuminated billboards or signs may
cause the high beam to switch to the low
beams, or the low beams to remain on.
O
The following factors may affect the
amount of time taken to turn the high
beam on or off:
• The brightness of headlights, fog lights,
and tail lights of vehicles ahead
• The movement and direction of vehicles
ahead
• When a vehicle ahead only has opera-
tional lights on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface etc.)
• The number of passengers and amount of
luggage
O
The high beam may be turned on or off
when the driver does not expect it.
O
Bicycles or similar objects may not be
detected.
O
In the situations shown below, the system
may not be able to accurately detect sur-
rounding brightness levels. This may
cause the low beams to remain on or the
high beams to cause problems for pedes-
trians, vehicles ahead or other parties. In
these cases, manually switch between the
high and low beams.
• In bad weather (rain, snow, fog, sand-
storms etc.)
• The windshield is obscured by fog, mist,
ice, dirt etc.
• The windshield is cracked or damaged.
• The front camera is deformed or dirty.
• Surrounding brightness levels are equal
to those of headlights, tail lights or fog
lights.
• Vehicles ahead have headlights or tail
lights that are either switched off, dirty,
192
4-3. Operating the lights and wipers
changing color, or have improperly
adjusted aim.
• When driving through an area of inter-
mittently changing brightness and dark-
ness.
• When frequently and repeatedly driving
ascending/descending roads, or roads
with rough, bumpy or uneven surfaces
(such as stone-paved roads, gravel tracks
etc.).
• When frequently and repeatedly taking
curves or driving on a winding road.
• There is a highly reflective object ahead
of the vehicle, such as a sign or a mirror.
• The vehicle’s headlights are damaged or
dirty.
• The vehicle is listing or titling, due to a flat
tire, a trailer being towed etc.
• The driver believes that the high beam
may be causing problems or distress to
other drivers or pedestrians nearby.
• The vehicle is used in a territory in which
vehicles travel on the opposite side of the
road of the country for which the vehicle
is approved, for example using a vehicle
designed for right-hand traffic in a left-
hand traffic territory, or vice versa.
Q
Switching to high beam
Push the lever away from you.
The AHB indicator will turn off and the
high beam indicator will turn on.
Pull the lever to its original position to acti-
vate the Automatic High Beam system
again.
Q
Switching to low beam
Press the Automatic High Beam
switch.
The AHB indicator will turn off.
Press the switch to activate the Automatic
High Beam system again.
Q
Temporarily switching to the low
beams
Pull the lever toward you and then
return it to its original position.
The high beams remain on while the lever
is pulled toward you, however, after the
lever is returned to its original position, the
low beams remain on for a certain amount
of time. Afterwards, the Automatic High
Beam will be activated again.
Turning the high beam on/off
manually
193
4
4-3. Operating the lights and wipers
Dr
ivin
g
Q
Temporarily switching to the low beams
It is recommended to switch to the low
beams when the high beam may cause
problems or distress to other drivers or
pedestrians nearby.
Turns the rear fog light on
Releasing the switch ring returns it to
.
Operating the switch ring again turns the
rear fog light off.
Q
Rear fog light can be used when
The headlights are turned on.
Each time the headlights are turned off, the
rear fog light is turned off.
Fog light switch
When in difficult driving conditions,
such as in rain and fog, turn on the
rear fog light to notify following
vehicles the existence of your vehi-
cle.
Turning on the rear fog light
194
4-3. Operating the lights and wipers
Operating the
lever operates
the wipers or washer as follows. When
AUTO is selected, the wipers will
operate automatically when the sen-
sor detects falling rain. The system
automatically adjusts wiper timing in
accordance with rain volume and vehi-
cle speed.
1
Off
2
Rain-sensing operation
3
Low speed operation
4
High speed operation
5
Temporary operation
When AUTO is selected, the sensor
sensitivity can be adjusted by turning
the switch ring.
6
Increases the sensitivity
7
Decreases the sensitivity
Windshield wipers and
washer
Operating the lever can switch
between automatic operation and
manual operation, or can use the
washer.
NOTICE
Q
When the windshield is dry
Do not use the wipers, as they may dam-
age the windshield.
Operating the wiper lever
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст