Lexus LC500 (2022 year). Manual in english — page 9
163
4
4-2. Driving procedures
Dr
ivin
g
Q
Operation of the power switch
O
If the switch is not pressed shortly and
firmly, the power switch mode may not
change or the hybrid system may not
start.
O
If attempting to restart the hybrid system
immediately after turning the power
switch off, the hybrid system may not start
in some cases. After turning the power
switch off, please wait a few seconds
before restarting the hybrid system.
Q
Customization
If the smart entry & start system has been
deactivated in a customized setting, refer to
P.392.
1
Stop the vehicle completely.
2
If the parking brake is in manual
mode, set the parking brake.
(
P.183)
3
Press the P position switch.
(
P.176)
Check that the shift position indicator
shows P and the parking brake indicator is
illuminated.
4
Press the power switch.
The hybrid system will stop, and the meter
display will be extinguished (the shift posi-
tion indicator will be extinguished a few
seconds after the meter display).
5
Check that “ACCESSORY” or
“IGNITION ON” is not shown on
the meter.
Q
Automatic P position selection function
P.177
WARNING
Q
When starting the hybrid system
Always start the hybrid system while sit-
ting in the driver’s seat. Do not depress
the accelerator pedal while starting the
hybrid system under any circumstances.
Doing so may cause an accident result-
ing in death or serious injury.
Q
Caution while driving
If hybrid system failure occurs while the
vehicle is moving, do not lock or open
the doors until the vehicle reaches a safe
and complete stop. Activation of the
steering lock in this circumstance may
lead to an accident, resulting in death or
serious injury.
NOTICE
Q
When starting the hybrid system
If the hybrid system becomes difficult to
start, have your vehicle checked by any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer immediately.
Q
Symptoms indicating a malfunction
with the power switch
If the power switch seems to be operat-
ing somewhat differently than usual, such
as the switch sticking slightly, there may
be a malfunction. Contact any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi-
ately.
Stopping the hybrid system
164
4-2. Driving procedures
Modes can be changed by pressing
the power switch with the brake pedal
released. (The mode changes each
time the switch is pressed.)
1
Off
The emergency flashers can be used.
2
ACCESSORY mode
Some electrical components such as the
audio system can be used.
“ACCESSORY” will be displayed on the
meter.
3
ON mode
All electrical components can be used.
“IGNITION ON” will be displayed on the
meter.
Q
Auto power off function
If the vehicle is left in ACCESSORY mode
for more than 20 minutes or ON mode (the
hybrid system is not operating) for more
than an hour with the shift position in P, the
power switch will automatically turn off.
However, this function cannot entirely pre-
vent the 12-volt battery discharge. Do not
leave the vehicle with the power switch in
ACCESSORY or ON mode for long peri-
ods of time when the hybrid system is not
operating.
WARNING
Q
Stopping the hybrid system in an
emergency
O
If you want to stop the hybrid system in
an emergency while driving the vehi-
cle, press and hold the power switch
for more than 2 seconds, or press it
briefly 3 times or more in succession.
(
P.363)
However, do not touch the power
switch while driving except in an emer-
gency. Turning the hybrid system off
while driving will not cause loss of
steering or braking control, however,
power assist to the steering will be lost.
This will make it more difficult to steer
smoothly, so you should pull over and
stop the vehicle as soon as it is safe to
do so.
O
If the power switch is operated while
the vehicle is running, a warning mes-
sage is shown on the multi-information
display and a buzzer sounds.
O
When restarting the hybrid system
after an emergency shutdown, press
the power switch.
Changing power switch modes
165
4
4-2. Driving procedures
Dr
ivin
g
Q
When the shift control system malfunc-
tions
When attempting to turn the power switch
off while there is a malfunction in the shift
control system, the power switch mode may
change to ACCESSORY mode. In this
case, ACCESSORY mode may be turned
off by applying the parking brake and
pressing the power switch again.
If there is a malfunction in the system, have
the vehicle inspected by any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer immediately.
Turns EV drive mode on/off
When EV drive mode is turned on, the EV
drive mode indicator will come on. Press-
ing the switch when in EV drive mode will
return the vehicle to normal driving (using
the gasoline engine and electric motor
[traction motor]).
NOTICE
Q
To prevent 12-volt battery discharge
O
Do not leave the power switch in
ACCESSORY or ON mode for long
periods of time without the hybrid sys-
tem on.
O
If “ACCESSORY” or “IGNITION
ON” is displayed on the meter, the
power switch is not off. Exit the vehicle
after turning the power switch off.
EV drive mode (LC500h)
In EV drive mode, electric power is
supplied by the hybrid battery
(traction battery), and only the
electric motor (traction motor) is
used to drive the vehicle.
This mode allows you to drive in res-
idential areas early in the morning
and late at night, or in indoor park-
ing lots etc. without concern for
noises and gas emissions.
Vehicles with the vehicle proximity
notification system: When the vehi-
cle proximity notification system is
active, the vehicle may produce
sound.
Operating instructions
166
4-2. Driving procedures
Q
Situations in which EV drive mode can-
not be turned on
It may not be possible to turn EV drive
mode on in the following situations. If it can-
not be turned on, a buzzer will sound and a
message will be shown on the multi-infor-
mation display.
O
The temperature of the hybrid system is
high.
The vehicle has been left in the sun,
driven on a hill, driven at high speeds, etc.
O
The temperature of the hybrid system is
low.
The vehicle has been left in temperatures
lower than about 0°C (32°F) for a long
period of time etc.
O
The gasoline engine is warming up.
O
The hybrid battery (traction battery) is
low.
The remaining battery level indicated in
the “Energy Monitor” display is low.
(
P.108)
O
Vehicle speed is high.
O
The accelerator pedal is depressed firmly
or the vehicle is on a hill etc.
O
The windshield defogger is in use.
O
When the shift position is in M.
Q
Switching to EV drive mode when the
gasoline engine is cold
If the hybrid system is started while the gas-
oline engine is cold, the gasoline engine will
start automatically in order to warm up. In
this case, you will become unable to switch
to EV drive mode.
To prevent gasoline engine warm up in
order to reduce noises, start the hybrid sys-
tem without starting the gasoline engine,
pressing the power switch with fully
depressing the brake pedal and pressing
the EV drive mode switch.
Q
Automatic cancelation of EV drive
mode
When driving in EV drive mode, the gaso-
line engine may automatically restart in the
following situations. When EV drive mode
is canceled, a buzzer will sound and the EV
drive mode indicator will flash and go off.
O
The hybrid battery (traction battery)
becomes low.
The remaining battery level indicated in
the “Energy Monitor” display is low.
(
P.108)
O
Vehicle speed is high.
O
The accelerator pedal is depressed firmly
or the vehicle is on a hill etc.
When it is possible to inform the driver of
automatic cancelation in advance, a prior
notice screen will appear on the multi-infor-
mation display.
Q
Possible driving distance when driving
in EV drive mode
EV drive mode’s possible driving distance
ranges from a few hundred meters to
approximately 1 km (0.6 mile). However,
depending on vehicle conditions, there are
situations when EV drive mode cannot be
used.
(The distance that is possible depends on
the hybrid battery [traction battery] level
and driving conditions.)
Q
Fuel economy
The hybrid system is designed to achieve
the best possible fuel economy during nor-
mal driving (using the gasoline engine and
electric motor [traction motor]). Driving in
EV drive mode more than necessary may
lower fuel economy.
167
4
4-2. Driving procedures
Dr
ivin
g
Q
If “EV Mode Unavailable” is shown on
the multi-information display
The EV drive mode is not available. The
reason the EV drive mode is not available
(the vehicle is idling, battery charge is low,
vehicle speed is higher than the EV drive
mode operating speed range or accelera-
tor pedal is depressed too much) may be
displayed. Use the EV drive mode when it
becomes available.
Q
If “EV Mode Deactivated” is shown on
the multi-information display
The EV drive mode has been automatically
canceled. The reason the EV drive mode is
not available (the battery charge is low,
vehicle speed is higher than the EV drive
mode operating speed range or accelera-
tor pedal is depressed too much) may be
displayed. Drive the vehicle for a while
before attempting to turn on the EV drive
mode again.
*1
: To improve fuel efficiency and reduce
noise, set the shift position in D for nor-
mal driving. You can choose gear range
suitable for your driving situation by
operating the paddle shift switches.
*2
: Any gear range can be fixed when driv-
ing in M mode.
Q
To protect the automatic transmission
If the automatic transmission fluid tempera-
ture is high, “Transmission Fluid Temp High
See Owner’s Manual” will be displayed on
the multi-information display and the vehi-
cle will go into transmission protection
mode automatically. Have the vehicle
inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reli-
able repairer.
WARNING
Q
Caution while driving
Vehicles without the vehicle proximity
notification system: When driving in EV
drive mode, pay special attention to the
area around the vehicle. Because there is
no engine noise, pedestrians, people rid-
ing bicycles or other people and vehicles
in the area may not be aware of the vehi-
cle starting off or approaching them, so
take extra care while driving.
Vehicles with the vehicle proximity notifi-
cation system: When driving in EV drive
mode, pay special attention to the area
around the vehicle. Because there is no
engine noise, pedestrians, people riding
bicycles or other people and vehicles in
the area may not be aware of the vehicle
starting off or approaching them. Take
extra care while driving even if the vehi-
cle proximity notification system is active.
Automatic transmission
(LC500)
Select the shift position depending
on your purpose and situation.
Shift position purpose and func-
tions
Shift position
Objective or function
P
Parking the vehicle/start-
ing the engine
R
Reversing
N
Neutral
(Condition in which the
power is not transmitted)
D
Normal driving
*1
M
M mode driving
*2
(
P.173)
168
4-2. Driving procedures
Q
When driving with cruise control or
dynamic radar cruise control with full-
speed range activated
Even when performing the following
actions with the intent of enabling engine
braking, engine braking will not be acti-
vated because cruise control or dynamic
radar cruise control with full-speed range
will not be canceled.
O
While driving in the D position, down-
shifting to 9, 8, 7, 6, 5 or 4.
O
When switching the driving mode to
sport mode while driving in D position.
(
P.238)
Q
Restraining sudden start (Drive-Start
Control)
P.149
Q
AI-SHIFT
The AI-SHIFT automatically selects the suit-
able gear according to driver performance
and driving conditions.
The AI-SHIFT automatically operates when
the shift position is in D. (Shifting the shift
position to M cancels the function.)
Q
If a message about a shift operation is
shown
To prevent the shift position from being
selected incorrectly or the vehicle from
moving unexpectedly, the shift position may
be changed automatically or operating the
shift lever may be required. In this case,
change the shift position following the mes-
sages on the multi-information display.
Q
After recharging/reconnecting the 12-
volt battery
P.332
Shift lever
Operate the shift lever gently and securely
in the direction of the arrow on the shift
WARNING
Q
When driving on slippery road sur-
faces
Do not accelerate or shift the shift posi-
tion suddenly.
Sudden changes in engine braking may
cause the vehicle to spin or skid, resulting
in an accident.
NOTICE
Q
Situations where shift control system
malfunctions are possible
If any of the following situations occurs,
shift control system malfunctions are
possible. Immediately stop the vehicle in
a safe place on level ground, apply the
parking brake, and then contact any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
O
When the warning message indicating
the shift control system appears on the
multi-information display. (
P.382)
O
The display indicates that no shift posi-
tion is selected for more than a few
seconds.
Shift position display and how to
change the shift position
A
169
4
4-2. Driving procedures
Dr
ivin
g
position indicator.
To shift to N, slide the shift lever in the
direction of the arrow and hold it.
Release the shift lever after each shifting
operation to allow it to return to its regular
position (
).
Shifting to M is only possible when the shift
position is in D.
When shifting from P to N, D or R, from N,
D, M or R to P, from D or M to R, or from R
to D, ensure that the brake pedal is being
depressed and the vehicle is stationary.
Shift position indicator
Meter display:
The current shift position is highlighted.
When any shift position other than D or M
is selected, the arrow toward M and M
position indicator are displayed in gray.
Shift lever display:
The current shift position is illuminated.
When selecting the shift position, make
sure that the shift position has been
changed to the desired position by check-
ing the shift position indicator provided on
the instrument cluster.
P position switch
Fully stop the vehicle and set the parking
brake, and then press the P position switch.
When the shift position is changed to P, the
switch illuminates.
Check that the shift position indicator
shows P.
Q
Changing the shift position in each
engine switch mode
O
The shift position cannot be changed
when the engine switch is in ACCES-
SORY mode or off.
O
When the engine switch is in IGNITION
ON mode, the shift position can only be
changed to N.
O
When the engine is running, the shift
position can be changed from P to D, N,
or R.
Q
Shifting the shift position from P to other
positions
O
While depressing the brake pedal firmly,
operate the shift lever. If the shift lever is
operated without depressing the brake
pedal, the buzzer will sound and the shift-
ing operation will be disabled.
O
When selecting the shift position, make
sure that the shift position has been
changed to the desired position by
checking the shift position indicator pro-
vided on the instrument cluster.
O
The shift position cannot be changed
from P to M directly.
Q
The shift position cannot be changed
when
In the following situations, a buzzer will
sound to inform you that the shift position
cannot be changed. Use the appropriate
operation to attempt to change the shift
position again.
O
When attempting to change the shift
position from P with the brake pedal not
depressed
O
When attempting to change the shift
position from P with the accelerator
pedal depressed
O
When attempting to change the shift
position from N while stopped or driving
at an extremely low speed with the brake
pedal not depressed
O
When attempting to change the shift
position from N while stopped or driving
at an extremely low speed with the accel-
erator pedal depressed
O
When attempting to change the shift
position from P or N to M
O
When the P position switch is pressed
while driving
When driving at an extremely low speed,
the shift position may change to P.
B
C
170
4-2. Driving procedures
Q
The shift position automatically changes
to N when
In the following situations, a buzzer will
sound to inform you that the shift position
has been changed to N. Use the appropri-
ate operation to attempt to change the shift
position again.
O
When attempting to change the shift
position to R while the vehicle is moving
forward
When driving at a low speed, the shift posi-
tion may change to R.
O
When attempting to change the shift
position to D while the vehicle is moving
backward
When driving at a low speed, the shift posi-
tion may change to D.
O
When attempting to change the shift
position from R to M
Q
If the N shift position is selected while
driving
If the shift lever is moved to N while driving
above a certain speed, the shift position will
change to N without holding the shift lever
in the N position. In this situation, a buzzer
will sound and a message will be displayed
on the multi-information display to inform
you that the shift position has been changed
to N.
Q
Automatic P position selection function
In the following situations, the shift position
is automatically changed to P.
O
When pressing the engine switch with
the vehicle stopped while the engine
switch is in IGNITION ON mode and
the shift position is in a position other than
P (after the shift position has changed to
P, the engine switch will turn off)
*
O
If the driver’s door is opened and all of the
following conditions are met, while the
shift position is in a position other than P
• The engine switch is in IGNITION ON
mode.
• The driver is not wearing the seat belt.
• The brake pedal is not depressed.
To start off the vehicle after the shift position
is changed to P, operate the shift lever
again.
O
When the vehicle is stopped after the
engine has been stopped in an emer-
gency while driving
O
When voltage of the 12-volt battery
drops while the shift position is in a posi-
tion other than P
*
: When the engine switch is pressed while
driving at extremely slow speeds, such as
immediately before stopping the vehicle,
the shift position may automatically
change to P. Make sure that the vehicle is
completely stopped before pressing the
engine switch.
Q
If the shift position cannot be shifted
from P
There is a possibility that the 12-volt battery
is discharged. Check the 12-volt battery in
this situation. (
P.396)
WARNING
Q
For the shift lever
O
Do not remove the shift lever knob or
use anything but a genuine Lexus shift
lever knob. Also, do not hang anything
on the shift lever. Doing so could pre-
vent the shift lever from returning to
position, causing unexpected acci-
dents to occur when the vehicle is in
motion.
O
In order to prevent the shift position
from accidentally being changed, do
not touch the shift lever when not using
them.
Q
P position switch
O
Do not press the P position switch
while the vehicle is moving.
If the P position switch is pressed when
driving at very low speeds (for exam-
ple, directly before stopping the vehi-
cle), the vehicle may stop suddenly
when the shift position switches to P,
which could lead to an accident.
171
4
4-2. Driving procedures
Dr
ivin
g
Performing the following operations
allows the engine switch to be set to
ACCESSORY mode with the shift
position held in N.
1
Operate the shift lever and change
the shift position to N when the
engine is running.
2
Return the shift lever to its regular
position (
).
3
Operate the shift lever to N and
hold it there until the buzzer
sounds.
4
Press the engine switch within 5
seconds after the buzzer sounds.
The engine switch will be set to ACCES-
SORY mode with the shift position in N.
*
Make sure to check that the buzzer sounds
and “Holding N Push P Switch When
Done” is displayed on the multi-informa-
tion display.
To change to a shift position other
than N, press the P position switch.
The shift position will be changed to
P.
Even if the engine is not operating,
by operating the shift lever and the
engine switch, the engine switch
may be changed to ACCESSORY
mode with the shift position held in
N. Make sure that the engine is
operating before performing the
operation.
*
: To keep this state, do not operate the
engine switch. If the engine switch is
operated repeatedly, the engine switch
will turn off after the shift position has
automatically changed to P.
WARNING
O
In order to prevent the shift position
from accidentally being changed, do
not touch the P position switch when
not using them.
NOTICE
Q
Notes regarding shift lever and P
position switch operation
Avoid repeatedly operating the shift
lever and P position switch in quick suc-
cession.
The system protection function may acti-
vate and it will not be temporarily possi-
ble to shift the shift position other than P.
If this happens, please wait for a while
before attempting to change the shift
position again.
Q
When exiting the vehicle (driver’s
seat only)
Check that the shift position indicator
shows P and that the parking brake indi-
cator is illuminated before opening the
door and exiting the vehicle.
When the engine switch is
changed to ACCESSORY
mode with the shift position held
in N
NOTICE
Q
Keeping the shift position in N when
changing to ACCESSORY mode
When you wish to keep the shift position
in N when changing the engine switch to
ACCESSORY mode, make sure that
the engine is running before operating
the engine switch.
If the engine switch mode is changed
without the engine running, the shift posi-
tion may change to P.
172
4-2. Driving procedures
Q
Driving mode
P.238
Q
Snow mode
Snow mode can be selected to suit the
conditions when driving on slippery
road surfaces, such as on snow.
Turn the
switch backward.
The snow mode indicator comes on.
Turn the
switch backward again to
return to normal mode.
Q
Snow mode automatic deactivation
Snow mode is automatically deactivated if
the engine switch is turned off after driving
in snow mode.
To drive using temporary shift range
selection, operate the “-” or “+” paddle
shift switch.
When the “-” paddle shift switch is
operated, the shift range switches to a
range that enables engine braking
force that is suitable to driving condi-
tions. When the “+” paddle shift switch
is operated, the shift range switches to
a range that is one range higher than
the current range.
Changing the shift range allows
restriction of the highest gear, prevent-
ing unnecessary upshifting and
enabling the level of engine braking
force to be selected.
1
Upshifting
2
Downshifting
The selected shift range, from D1 to D10,
will be displayed in the meter.
To return to normal D position driving, the
“+” paddle shift switch must be held down
for a period of time.
A lower shift range will provide greater
engine braking forces than a higher shift
range.
Selecting the driving mode
Selecting shift ranges in the D
position
Meter display
Function
D2 - D10
A gear in the range
between D1 and the
selected shift range is
automatically chosen
depending on vehicle
speed and driving condi-
tions
D1
Setting the shift range at D1
173
4
4-2. Driving procedures
Dr
ivin
g
Q
Automatic deactivation of shift range
selection in the D position
Shift range selection in the D position will
be deactivated in the following situations:
O
When the vehicle comes to a stop
O
If the accelerator pedal is depressed for
more than a certain period of time
O
When the shift lever is moved to D again
O
When pressing and holding the “+” pad-
dle shift switch
Q
Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some-
times be restricted. In some circumstances,
downshifting may not be possible even
when the paddle shift switch is operated. (A
buzzer will sound twice.)
To enter M mode, shift the shift posi-
tion to M. Gears can be selected by
operating the paddle shift switches,
allowing you to drive in the gear of
your choosing.
1
Upshifting
2
Downshifting
The gear changes once every time the
paddle shift switch is operated.
The selected gear, from M1 to M10, will be
fixed and displayed in the meter.
When in the M position, the gear will
not change unless the paddle shift
switches are operated.
However, even when in the M position,
the gears will be automatically
changed in the following situation:
When vehicle speed drops (down-
shift only).
When it is necessary to protect the
engine or automatic transmission
when the engine coolant tempera-
ture is low, the automatic transmis-
sion fluid temperature is high or low,
or other reasons.
Also, the gear will not shift when the
vehicle speed is low, even if an upshift
operation is performed.
Q
Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some-
times be restricted. In some circumstances,
downshifting may not be possible even
when the paddle shift switch is operated. (A
buzzer will sound twice.)
The Gear Shift Indicator display is a
guide to help the driver achieve
improved fuel economy and reduced
exhaust emissions within limits of
engine performance.
Selecting gears in the M position
Gear Shift Indicator (if
equipped)
174
4-2. Driving procedures
When not in operation
Shift-up indicator
Q
Gear Shift Indicator function
This function automatically operates
during M mode.
By following the Shift-up indicator
and shifting up accordingly, it is pos-
sible to achieve improved fuel econ-
omy and reduced exhaust
emissions.
The Gear Shift Indicator does not
have a similar function for down-
shifting.
Depending on the driving condi-
tions, the Gear Shift Indicator may
not display the Shift-up indicator
while driving in M mode.
*1
: To improve fuel efficiency and reduce
noise, set the shift position in D for nor-
mal driving. You can choose gear range
suitable for your driving situation by
operating the paddle shift switches.
*2
: Any gear range can be fixed when driv-
ing in M mode.
Q
To protect the hybrid transmission
If the transmission fluid temperature is high,
“Transmission Fluid Temp High See
Owner’s Manual” will be displayed on the
multi-information display and the vehicle
will go into transmission protection mode
automatically. Have the vehicle inspected
by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
WARNING
Q
Gear Shift Indicator display
For safety, the driver should not look only
at the display. Refer to the display when it
is safe to do so while considering actual
traffic and road conditions.
Failure to do so may lead to an accident.
A
B
Hybrid transmission
(LC500h)
Select the shift position depending
on your purpose and situation.
Shift position purpose and func-
tions
Shift position
Objective or function
P
Parking the vehicle/start-
ing the hybrid system
R
Reversing
N
Neutral
(Condition in which the
power is not transmitted)
D
Normal driving
*1
M
M mode driving
*2
(
P.180)
175
4
4-2. Driving procedures
Dr
ivin
g
Q
When driving with cruise control or
dynamic radar cruise control with full-
speed range activated
O
When cruise control or dynamic radar
cruise control with full-speed range is
operating, the system does not respond
to paddle shift switch operations.
O
Even when the driving mode is switched
to sport mode with the intent of enabling
engine braking, cruise control or
dynamic radar cruise control with full-
speed range is not canceled and engine
braking is not activated.
Q
Restraining sudden start (Drive-Start
Control)
P.149
Q
AI-SHIFT
The AI-SHIFT automatically selects the suit-
able gear according to driver performance
and driving conditions. The AI-SHIFT auto-
matically operates when the shift position is
in D. (Shifting the shift position to M cancels
the function.)
Q
If a message about a shift operation is
shown
To prevent the shift position from being
selected incorrectly or the vehicle from
moving unexpectedly, the shift position may
be changed automatically or operating the
shift lever may be required. In this case,
change the shift position following the mes-
sages on the multi-information display.
Q
After recharging/reconnecting the 12-
volt battery
P.332
WARNING
Q
When driving on slippery road sur-
faces
Do not accelerate or shift the shift posi-
tion suddenly.
Sudden changes in engine braking may
cause the vehicle to spin or skid, resulting
in an accident.
NOTICE
Q
Hybrid battery (traction battery)
charge
If the shift position is in N, the hybrid bat-
tery (traction battery) will not be
charged. To help prevent the battery
from discharging, avoid leaving the N
position selected for an extended period
of time.
Q
Situations where shift control system
malfunctions are possible
If any of the following situations occurs,
shift control system malfunctions are
possible. Immediately stop the vehicle in
a safe place on level ground, apply the
parking brake, and then contact any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
O
When the warning message indicating
the shift control system appears on the
multi-information display. (
P.382)
O
The display indicates that no shift posi-
tion is selected for more than a few
seconds.
176
4-2. Driving procedures
Shift lever
Operate the shift lever gently and securely
in the direction of the arrow on the shift
position indicator.
To shift to N, slide the shift lever in the
direction of the arrow and hold it.
Release the shift lever after each shifting
operation to allow it to return to its regular
position (
).
Shifting to M is only possible when the shift
position is in D.
When shifting from P to N, D or R, from N,
D, M or R to P, from D or M to R, or from R
to D, ensure that the brake pedal is being
depressed and the vehicle is stationary.
Shift position indicator
Meter display:
The current shift position is highlighted.
When any shift position other than D or M
is selected, the arrow toward M and M
position indicator are displayed in gray.
Shift lever display:
The current shift position is illuminated.
When selecting the shift position, make
sure that the shift position has been
changed to the desired position by check-
ing the shift position indicator provided on
the instrument cluster.
P position switch
Fully stop the vehicle and set the parking
brake, and then press the P position switch.
When the shift position is changed to P, the
switch illuminates.
Check that the shift position indicator
shows P.
Q
Changing the shift position in each
power switch mode
O
The shift position cannot be changed
when the power switch is in ACCES-
SORY mode or off.
O
When the power switch is in ON mode, if
the “READY” indicator is not illuminated,
the shift position can only be changed to
N.
O
When the “READY” indicator is illumi-
nated, the shift position can be changed
from P to D, N, or R.
O
When the “READY” indicator is flashing,
the shift position cannot be changed from
P to any other position, even if the shift
lever is operated. Operate the shift lever
again after the “READY” indicator
changes from flashing to illuminated.
Q
Shifting the shift position from P to other
positions
O
While depressing the brake pedal firmly,
operate the shift lever. If the shift lever is
operated without depressing the brake
pedal, the buzzer will sound and the shift-
ing operation will be disabled.
O
When selecting the shift position, make
sure that the shift position has been
Shift position display and how to
change the shift position
A
B
C
177
4
4-2. Driving procedures
Dr
ivin
g
changed to the desired position by
checking the shift position indicator pro-
vided on the instrument cluster.
O
The shift position cannot be changed
from P to M directly.
Q
The shift position cannot be changed
when
In the following situations, a buzzer will
sound to inform you that the shift position
cannot be changed. Use the appropriate
operation to attempt to change the shift
position again.
O
When attempting to change the shift
position from P with the brake pedal not
depressed
O
When attempting to change the shift
position from P with the accelerator
pedal depressed
O
When attempting to change the shift
position from N while stopped or driving
at an extremely low speed with the brake
pedal not depressed
O
When attempting to change the shift
position from N while stopped or driving
at an extremely low speed with the accel-
erator pedal depressed
O
When attempting to change the shift
position from P or N to M
O
When the P position switch is pressed
while driving
When driving at an extremely low speed,
the shift position may change to P.
Q
The shift position automatically changes
to N when
In the following situations, a buzzer will
sound to inform you that the shift position
has been changed to N. Use the appropri-
ate operation to attempt to change the shift
position again.
O
When attempting to change the shift
position to R while the vehicle is moving
forward
When driving at a low speed, the shift posi-
tion may change to R.
O
When attempting to change the shift
position to D while the vehicle is moving
backward
When driving at a low speed, the shift posi-
tion may change to D.
O
When attempting to change the shift
position from R to M
Q
If the N shift position is selected while
driving
If the shift lever is moved to N while driving
above a certain speed, the shift position will
change to N without holding the shift lever
in the N position. In this situation, a buzzer
will sound and a message will be displayed
on the multi-information display to inform
you that the shift position has been changed
to N.
Q
Automatic P position selection function
In the following situations, the shift position
is automatically changed to P.
O
When pressing the power switch with the
vehicle stopped while the power switch is
in ON mode and the shift position is in a
position other than P (after the shift posi-
tion has changed to P, the power switch
will turn off)
*
O
If the driver’s door is opened and all of the
following conditions are met, while the
shift position is in a position other than P
• The power switch is in ON mode.
• The driver is not wearing the seat belt.
• The brake pedal is not depressed.
To start off the vehicle after the shift position
is changed to P, operate the shift lever
again.
O
When the vehicle is stopped after the
hybrid system has been stopped in an
emergency while driving
O
When voltage of the 12-volt battery
drops while the shift position is in a posi-
tion other than P
*
: When the power switch is pressed while
driving at extremely slow speeds, such as
immediately before stopping the vehicle,
the shift position may automatically
change to P. Make sure that the vehicle is
completely stopped before pressing the
178
4-2. Driving procedures
power switch.
Q
If the shift position cannot be shifted
from P
There is a possibility that the 12-volt battery
is discharged. Check the 12-volt battery in
this situation. (
P.396)
Performing the following operations
allows the power switch to be set to
ACCESSORY mode with the shift
position held in N.
1
Operate the shift lever and change
the shift position to N when the
hybrid system is operating.
2
Return the shift lever to its regular
position (
).
3
Operate the shift lever to N and
hold it there until the buzzer
sounds.
4
Press the power switch within 5
seconds after the buzzer sounds.
The power switch will be set to ACCES-
SORY mode with the shift position in N.
*
WARNING
Q
For the shift lever
O
Do not remove the shift lever knob or
use anything but a genuine Lexus shift
lever knob. Also, do not hang anything
on the shift lever. Doing so could pre-
vent the shift lever from returning to
position, causing unexpected acci-
dents to occur when the vehicle is in
motion.
O
In order to prevent the shift position
from accidentally being changed, do
not touch the shift lever when not using
them.
Q
P position switch
O
Do not press the P position switch
while the vehicle is moving.
If the P position switch is pressed when
driving at very low speeds (for exam-
ple, directly before stopping the vehi-
cle), the vehicle may stop suddenly
when the shift position switches to P,
which could lead to an accident.
O
In order to prevent the shift position
from accidentally being changed, do
not touch the P position switch when
not using them.
NOTICE
Q
Notes regarding shift lever and P
position switch operation
Avoid repeatedly operating the shift
lever and P position switch in quick suc-
cession.
The system protection function may acti-
vate and it will not be temporarily possi-
ble to shift the shift position other than P.
If this happens, please wait for a while
before attempting to change the shift
position again.
Q
When exiting the vehicle (driver’s
seat only)
Check that the shift position indicator
shows P and that the parking brake indi-
cator is illuminated before opening the
door and exiting the vehicle.
When the power switch is
changed to ACCESSORY
mode with the shift position held
in N
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст