Lexus GS300/400 (2000 year). Manual — part 257
SA0R8–01
W00274
SST
SST
R06214
SST
R08018
SST
SST
SA–14
–
SUSPENSION AND AXLE
FRONT AXLE HUB
2014
REASSEMBLY
1.
INSTALL BEARING
(a)
Using SST and a press, install a new bearing to steering
knuckle.
SST
09309–36010, 09950–60020 (09951–00720),
09950–70010 (09951–07150)
NOTICE:
If the inner race and balls come loose from the bearing out-
er race, make sure to install them on the same side as be-
fore.
(b)
Using snap ring pliers, install a new snap ring.
2.
INSTALL OIL SEAL
(a)
Install the inner race (outside).
(b)
Using SST and a hammer, install a new oil seal until it is
flush with the end surface of the steering knuckle.
SST
09608–32010
(c)
Coat MP grease to the oil seal lip.
3.
INSTALL AXLE HUB TO STEERING KNUCKLE
(a)
Install the brake dust cover to the steering knuckle with
the 4 bolts.
Torque: 8.3 N·m (85 kgf·cm, 74 in.·lbf)
(b)
Using SST and a press, install the axle hub to the steering
knuckle.
SST
09316–60011 (09316–00011, 09316–00071),
09608–32010
4.
INSTALL ABS SPEED SENSOR ROTOR
NOTICE:
Do not scratch the serrations of the sensor rotor.
5.
INSTALL AXLE HUB LOCK NUT
(a)
Install a new axle hub lock nut.
Torque: 199 N·m (2,030 kgf·cm, 147 ft·lbf)
(b)
Using a chisel and hammer, stake the lock nut.
6.
INSTALL FRONT HUB GREASE CAP
Using a screwdriver and hammer, install the grease cap to the
steering knuckle.
SA0R9–01
–
SUSPENSION AND AXLE
FRONT AXLE HUB
SA–15
2015
INSTALLATION
Installation is in the reverse order of removal (See page
).
AFTER INSTALLATION, CHECK ABS SPEED SENSOR SIGNAL (See page
WHEEL ALIGNMENT (See page
SA0RA–01
F02311
R05811
SST
R05812
Washer
SA–16
–
SUSPENSION AND AXLE
FRONT WHEEL HUB BOLT
2016
FRONT WHEEL HUB BOLT
REPLACEMENT
1.
REMOVE FRONT WHEEL
2.
REMOVE BRAKE CALIPER AND DISC
(a)
Remove the 2 bolts and remove the brake caliper from the
steering knuckle.
(b)
Support the brake caliper securely.
(c)
Remove the disc.
3.
REMOVE HUB BOLT
Using SST, remove the hub bolt.
SST
09628–10011
4.
INSTALL HUB BOLT
(a)
Install a washer and nut to the bolt, as shown in the il-
lustration.
(b)
Turn the wheel nut to pull the hub bolt until the underside
of the hub bolt head touches the axle hub.
5.
INSTALL DISC AND BRAKE CALIPER
(a)
Install the disc.
(b)
Install the brake caliper and 2 bolts to the steering
knuckle.
Torque: 118 N·m (1,200 kgf·cm, 87 ft·lbf)
6.
INSTALL FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
SA0RB–03
F02335
Suspension
Support No.2
Spring Bumper
Coil Spring
Suspension Support
No.1
Shock Absorber
With Coil Spring
Upper Suspension
Arm
Stabilizer Bar
ABS Speed Sensor
Shock Absorber
Clip
27 (280, 20)
56 (570, 41)
5.0 (55, 48 in.·lbf)
7.8 (80, 69 in.·lbf)
87 (890, 64)
O–Ring
Non–reusable part
: Specified torque
N·m (kgf·cm, ft·lbf)
157 (1,600, 116)
55 (560, 41)
–
SUSPENSION AND AXLE
FRONT SHOCK ABSORBER
SA–17
2017
FRONT SHOCK ABSORBER
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст