Lexus RX300 (MCU15). Manual — part 546
SA16Z–02
SA–24
–
SUSPENSION AND AXLE
FRONT DRIVE SHAFT
LEXUS RX300 (RM785E)
INSTALLATION
Installation is in the reverse order of removal (See page SA–17).
HINT:
After installation, check the ABS speed sensor signal (See page DI–205) and front wheel alignment (See
page SA–4).
SA10J–07
F14056
N·m (kgf·cm, ft·lbf)
: Specified torque
z
Non–reusable part
8.8 (90, 7.8 in.·lbf)
Reservoir
Tank
Shock Absorber
with Coil Spring
Stabilizer Bar Link
Suspension Support
Ball Bearing
Spring Upper Seat
Spring Bumper
Lower Insulator
Upper
Insulator
Coil Spring
ABS Speed Sensor
Wire Harness
Shock Absorber
Flexible Hose
80 (820, 59)
49 (500, 36)
39 (400, 29)
210 (2,150, 155)
29 (300, 21)
z
–
SUSPENSION AND AXLE
FRONT SHOCK ABSORBER
SA–25
LEXUS RX300 (RM785E)
FRONT SHOCK ABSORBER
COMPONENTS
SA10K–04
F14057
SA–26
–
SUSPENSION AND AXLE
FRONT SHOCK ABSORBER
LEXUS RX300 (RM785E)
REMOVAL
1.
REMOVE FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2.
DISCONNECT FLEXIBLE HOSE AND ABS SPEED
SENSOR WIRE HARNESS CLAMPS FROM SHOCK
ABSORBER
Remove the bolt and disconnect the flexible hose and ABS
speed sensor wire harness clamps from shock absorber brack-
et.
Torque: 29 N·m (300 kgf·cm, 21 ft·lbf)
3.
DISCONNECT STABILIZER BAR LINK FROM SHOCK
ABSORBER (See page SA–40)
4.
REMOVE SHOCK ABSORBER WITH COIL SPRING
(a)
Loosen the 2 nuts on the lower side of shock absorber.
Torque: 210 N·m (2,150 kgf·cm, 155 ft·lbf)
HINT:
Do not remove the 2 bolts.
(b)
LH side (LHD only):
Remove the reservoir tank set bolt and disconnect the
connector.
Torque: 8.8 N·m (90 kgf·cm, 7.8 in.·lbf)
(c)
Remove the 3 nuts on the upper side of the shock absorb-
er.
Torque: 80 N·m (820 kgf·cm, 59 ft·lbf)
(d)
Remove the 2 nuts and bolts on the lower side of shock
absorber.
HINT:
At the time of installation, coat the nut’s thread with engine oil.
(e)
Remove the shock absorber with coil spring.
SA10L–03
F03956
SST
SST
F03957
SST
–
SUSPENSION AND AXLE
FRONT SHOCK ABSORBER
SA–27
LEXUS RX300 (RM785E)
DISASSEMBLY
REMOVE COIL SPRING
(a)
Install 2 nuts and a bolt to the bracket at the lower side of
the shock absorber and secure it in a vise.
(b)
Using SST, compress the coil spring.
SST
09727–30021
NOTICE:
Do not use an impact wrench. It will damage the SST.
HINT:
Use 2 of the same type of SST.
(c)
Using SST to hold the spring upper seat, remove the nut.
SST
09729–22031
(d)
Remove the suspension support, ball bearing, spring up-
per seat and upper insulator.
(e)
Remove the coil spring, spring bumper and lower insula-
tor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст