Lexus RX300 (MCU15). Manual — part 571
D03839
A
B
C
D
E
F
G
H
I
J
–
AUTOMATIC TRANSAXLE
COMPONENT PARTS
AX–27
U140F AX (RM848E)
BEARING AND RACES INSTALLATION POSITION AND DIRECTION
AX–28
–
AUTOMATIC TRANSAXLE
COMPONENT PARTS
U140F AX (RM848E)
Mark
Front Race Diameter
Inside / Outside mm (in.)
Thrust Bearing Diameter
Inside / Outside mm (in.)
Rear Race Diameter
Inside / Outside mm (in.)
A
–
57.2 (2.252) / 84.96 (3.3449)
56.4 (2.220) / 83.0 (3.268)
B
–
37.73 (1.4854) / 58.0 (2.283)
29.9 (1.177) / 55.5 (2.185)
C
–
33.85 (1.3327) / 52.2 (2.055)
–
D
–
23.5 (0.925) / 44.0 (1.732)
–
E
–
36.3 (1.429) / 52.2 (2.055)
34.5 (1.358) / 48.5 (1.909)
F
–
34.6 (1.362) / 52.2 (2.055)
–
G
40.3 (1.587) / 58.0 (2.283)
38.6 (1.520) / 60.0 (2.362)
38.6 (1.520) / 58.0 (2.283)
H
–
53.6 (2.110) / 69.6 (2.740)
–
I
–
33.7 (1.327) / 48.2 (1.898)
30.3 (1.193) / 46.0 (1.811)
J
–
53.6 (2.110) / 70.18 (2.763) or 69.6 (2.740)
–
D03607
D03915
D03807
SST
D03806
D03914
–
AUTOMATIC TRANSAXLE
COMPONENT PARTS
AX–29
U140F AX (RM848E)
1.
INSTALL APPLY PIPE
Install the apply pipe and clamp with the bolt to the transaxle
case.
Torque: 9.8 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Make sure to insert the pipe to the stopper.
2.
INSTALL U/D CYLINDRICAL ROLLER BEARING
(a)
Install the oil seal ring to the transaxle housing.
(b)
Using SST and a press, install the U/D cylindrical roller
bearing.
SST
09950–60020, (09951–00810), 09950–70010,
(09951–07100)
NOTICE:
Do not apply excessive pressure to it.
3.
CHECK U/D BRAKE PISTON RETURN SPRING
Using vernier calipers, measure the free length of the spring to-
gether with the spring seat.
Standard free length: 13.24 mm (0.5212 in.)
4.
INSTALL U/D BRAKE
(a)
Install the 2 oil seal rings to the transaxle case.
D03809
SST
Vinyl Tape
D03810
SST
D03794
D03609
D03610
SST
AX–30
–
AUTOMATIC TRANSAXLE
COMPONENT PARTS
U140F AX (RM848E)
(b)
Wind a vinyl tape around SST at the place 4.0 mm (0.157
in.) above from the bottom end until the thickness of the
wound tape is about 5.0 mm (0.197 in.).
SST
09550–60010 (09951–00320)
NOTICE:
Clean SST to remove deposited oil, before winding a vinyl
tape.
(c)
Using SST and a press, install the needle–roller bearing
to the transaxle case.
SST
09950–60010, (09951–00320), 09950–70010
(09951–07100)
NOTICE:
When the wound vinyl tape contacts the transaxle case,
stop press–fitting.
(d)
Coat 2 new O–rings with ATF, install them to the U/D
brake piston.
(e)
Install the U/D brake piston to the transaxle case.
(f)
Using SST, a snap ring expander and press, install the
piston return spring and snap ring to the transaxle case.
SST
09387–00020
NOTICE:
S
Press–fit the bearing race RH until it contacts the
snap ring.
S
Do not apply excessive pressure to it.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст