Lexus RX450h L (2022 year). Manual in english — page 6

106

3-1. Key information

3-1.Key information

The following keys are provided with
the vehicle.

Electronic keys

• Operating the smart access system with

push-button start (

P.125)

• Operating the wireless remote control

function (

P.107)

Mechanical keys
Key number plate

When riding in an aircraft

When bringing an electronic key onto an

aircraft, make sure you do not press any

buttons on the electronic key while inside

the aircraft cabin. If you are carrying an

electronic key in your bag, etc., ensure that

the buttons are not likely to be pressed acci-

dentally. Pressing a button may cause the

electronic key to emit radio waves that

could interfere with the operation of the air-

craft.

Electronic key battery depletion

The standard battery life is 1 to 2 years.

If the battery becomes low, an alarm will

sound in the cabin when the hybrid sys-

tem is stopped.

To reduce key battery depletion when the

electronic key is to not be used for long

periods of time, set the electronic key to

the battery-saving mode. (

P.126)

As the electronic key always receives

radio waves, the battery will become

depleted even if the electronic key is not

used. The following symptoms indicate

that the electronic key battery may be

depleted. Replace the battery when nec-

essary.

• The smart access system with push-but-

ton start or the wireless remote control

does not operate.

• The detection area becomes smaller.

• The LED indicator on the key surface

does not turn on.

To avoid serious deterioration, do not

leave the electronic key within 3 ft. (1 m)

of the following electrical appliances that

produce a magnetic field:

• TVs

• Personal computers

• Cellular phones, cordless phones and

battery chargers

• Recharging cellular phones or cordless

phones

• Table lamps

• Induction cookers

Replacing the battery

P.386

Confirmation of the registered key

number

The number of keys already registered to

the vehicle can be confirmed. Ask your

Lexus dealer for details.

If “A New Key has been Registered

Contact Your Dealer for Details” is

shown on the multi-information display

This message will be displayed each time

the driver’s door is opened when the doors

are unlocked from the outside for approxi-

mately one week after a new electronic key

has been registered.

If this message is displayed but you have not

had a new electronic key registered, ask

your Lexus dealer to check if an unknown

electronic key (other than those in your

possession) has been registered.

Keys

The keys

A

B
C

107

3-1. Key information

3

Be

fore
dri
ving

The electronic keys are equipped with
the following wireless remote control:

Locks all the doors (

P.109)

Unlocks all the doors (

P.109)

Opens the windows

*2

and the

moon roof

*1, 2

or panoramic moon

roof

*1, 2

(

P.109)

Opens and closes the power back
door (

P.114)

Sounds the alarm

*1

: If equipped

*2

: These settings must be customized at

your Lexus dealer.

Theft deterrent panic mode

When

is pressed for longer than

about one second, an alarm will sound

intermittently and the vehicle lights will flash

to deter any person from trying to break

into or damage your vehicle.
To stop the alarm, press any button on the

electronic key.

To take out the mechanical key, push

NOTICE

To prevent key damage

Do not drop the keys, subject them to

strong shocks or bend them.

Do not expose the keys to high tem-

peratures for long periods of time.

Do not get the keys wet or wash them

in an ultrasonic washer, etc.

Do not attach metallic or magnetic

materials to the keys or place the keys

close to such materials.

Do not disassemble the keys.

Do not attach a sticker or anything else

to the surface of the electronic key.

Do not place the keys near objects that

produce magnetic fields, such as TVs,

audio systems and induction cookers,

or medical electrical equipment, such

as low-frequency therapy equipment.

Carrying the electronic key on your

person

Carry the electronic key 3.9 in. (10 cm)

or more away from electric appliances

that are turned on. Radio waves emitted

from electric appliances within 3.9 in. (10

cm) of the electronic key may interfere

with the key, causing the key to not func-

tion properly.

In case of a smart access system with

push-button start malfunction or

other key-related problems

P.439

When an electronic key is lost

P.438

Wireless remote control

Using the mechanical key

A
B
C

D

E

108

3-1. Key information

the release button and take the key out.

The mechanical key can only be inserted in
one direction, as the key only has grooves
on one side. If the key cannot be inserted in
a lock cylinder, turn it over and re-attempt
to insert it.
After using the mechanical key, store it in
the electronic key. Carry the mechanical
key together with the electronic key. If the
electronic key battery is depleted or the
entry function does not operate properly,
you will need the mechanical key.
(

P.439)

When required to leave the vehicle’s

key with a parking attendant

Lock the glove box as circumstances

demand. (

P.320)

Remove the mechanical key for your own

use and provide the attendant with the elec-

tronic key only.

If you lose your mechanical keys

P.438

If a wrong key is used

The key cylinder rotates freely, isolated

from the internal mechanism.

109

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

3-2.Opening, closing and locking the doors

Smart access system with
push-button start

Carry the electronic key to enable this
function.

1

Grip the driver’s door handle to
unlock the door. Grip any passen-
ger door handle to unlock all the
doors.

*

Make sure to touch the sensor on the back
of the handle.
The doors cannot be unlocked for 3 sec-
onds after the doors are locked.

*

: The door unlock settings can be

changed.

2

Touch the lock sensor (indentation
on the surface of the door handle)
to lock all the doors.

Check that the door is securely locked.

Wireless remote control

1

Locks all the doors

Check that the door is securely locked.

2

Unlocks all the doors

Pressing the button unlocks the driver’s
door. Pressing the button again within 3
seconds unlocks the other doors.
Press and hold to open the windows

*2

and

the moon roof

*1, 2

or panoramic moon

roof

*1, 2

*1

: If equipped

*2

: This setting must be customized at your

Lexus dealer.

Switching the door unlock function

It is possible to set which doors the entry

function unlocks using the wireless remote

control.

1

Turn the power switch off.

2

When the indicator light on the key sur-
face is not on, press and hold

,

or

for approxi-

mately 5 seconds while pressing and
holding .

The setting changes each time an operation

is performed, as shown below. (When

changing the setting continuously, release

the buttons, wait for at least 5 seconds, and

repeat step

2

.)

Side doors

The vehicle can be locked and
unlocked using the entry function,
wireless remote control or door
lock switches.

Unlocking and locking the doors
from the outside

110

3-2. Opening, closing and locking the doors

To prevent unintended triggering of the

alarm, unlock the doors using the wireless

remote control and open and close a door

once after the settings have been changed.

(If a door is not opened within 60 seconds
after

is pressed, the doors will be

locked again and the alarm will automati-

cally be set.)

In a case that the alarm is triggered, imme-

diately stop the alarm. (

P.74)

Impact detection door lock release sys-

tem

In the event that the vehicle is subject to a

strong impact, all the doors are unlocked.

Depending on the force of the impact or the

type of accident, however, the system may

not operate.

Operation signals

Doors:
A buzzer sounds and the emergency flash-

ers flash to indicate that the doors have

been locked/unlocked. (Locked: Once;

Unlocked: Twice)
Windows and moon roof or panoramic

moon roof:
A buzzer sounds.

Security feature

If a door is not opened within approximately

60 seconds after the vehicle is unlocked,

the security feature automatically locks the

vehicle again.

When the door cannot be locked by the

lock sensor on the surface of the door

handle

When the door cannot be locked even if the

lock sensor on the surface of the door han-

dle is touched by a finger, touch the lock

sensor with the palm.
When gloves are being worn, remove the

gloves.

Door lock buzzer

If an attempt to lock the doors using the

smart key system is made when a door is

not fully closed, a buzzer will sound continu-

ously for 5 seconds. Fully close the door to

stop the buzzer, and lock the doors again.

Setting the alarm

Locking the doors will set the alarm system.

(

P.74)

Conditions affecting the operation of

the smart access system with push-but-

ton start or wireless remote control

P.126

If the smart access system with

push-button start or the wireless remote

control does not operate properly

Use the mechanical key to lock and unlock

the doors. (

P.439)

Replace the key battery with a new one if it

is depleted. (

P.386)

If the 12-volt battery is discharged

The doors cannot be locked and unlocked

using the smart access system with

push-button start or wireless remote con-

trol. Lock or unlock the doors using the

Multi-information

display/Beep

Unlocking function

Exterior: Beeps 3

times

Interior: Pings once

Holding the driver’s
door handle unlocks
only the driver’s
door.

Holding any of the
passenger door
handles unlocks all
the doors.

Exterior: Beeps

twice

Interior: Pings once

Holding a door han-
dle unlocks all the
doors.

111

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

mechanical key. (

P.439)

Customization

Some functions can be customized.

(

P.472)

Door lock switches (to
lock/unlock)

1

Locks all the doors

2

Unlocks all the doors

Inside lock buttons (to lock)

Push down the inside lock button to
lock the door.

Inside door handles (to unlock)

For the front doors

Pull the handle to unlock and open the
door.

When the door is unlocked, the inside lock
button will pop up.

For the rear doors

Pull the handle to unlock the door. Pull
the handle a second time to open the
door.

WARNING

To prevent an accident

Observe the following precautions while

driving the vehicle.

Failure to do so may result in a door

opening and an occupant falling out,

resulting in death or serious injury.

Ensure that all doors are properly

closed and locked.

Do not pull the inside handle of the

doors while driving.

Be especially careful for the front doors,
as the doors may be opened even if the
inside lock buttons are in locked position.

Set the rear door child-protector locks

when children are seated in the rear

seats.

When opening or closing a door

Check the surroundings of the vehicle

such as whether the vehicle is on an

incline, whether there is enough space

for a door to open and whether a strong

wind is blowing. When opening or clos-

ing the door, hold the door handle tightly

to prepare for any unpredictable move-

ment.

Unlocking and locking the doors
from the inside

112

3-2. Opening, closing and locking the doors

When the door is unlocked, the inside lock
button will pop up.

Locking the doors from the outside with-

out a key

1

Push down the inside lock button.

2

Close the door.

The door cannot be locked if the power

switch is in ACCESSORY or ON mode, or

the electronic key is left inside the vehicle.

However, the key may not be detected cor-

rectly and the door may be locked.

Open door warning buzzer

If the vehicle speed reaches 3 mph (5

km/h), the master warning light flashes and

a buzzer sounds to indicate that door(s) or

the hood in not fully closed.

The open door(s) or hood is displayed on

the multi-information display.

The door cannot be opened from
inside the vehicle when the lock is set.

1

Unlock

2

Lock

These locks can be set to prevent children
from opening the rear doors. Push down
on each rear door switch to lock both rear
doors.

The following functions can be set or
canceled:

For instructions on customizing, refer to
P.472.

Rear door child-protector lock

Automatic door locking and
unlocking systems

Function

Operation

Speed linked
door locking
function

All doors are automati-
cally locked when vehi-
cle speed is
approximately 12 mph
(20 km/h) or higher.

Shift position
linked door lock-
ing function

All doors are automati-
cally locked when shift-
ing the shift lever out of
P.

Shift position
linked door
unlocking func-
tion

All doors are automati-
cally unlocked when
shifting the shift lever
to P.

Driver’s door
linked door
unlocking func-
tion

All doors are automati-
cally unlocked when
driver’s door is
opened.

113

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

Power back door

The power back door can be
opened using the power back door
opener switch, smart access system
with push-button start or wireless
remote control.

WARNING

Observe the following precautions.

Failure to do so may result in death or

serious injury.

Before driving the vehicle

Before driving the vehicle, make sure

that the power back door is fully closed. If

the power back door is not fully closed, it

may open unexpectedly while driving,

causing an accident.

Caution while driving

Keep the power back door closed

while driving.

If the power back door is left open, it may

hit nearby objects while driving or lug-

gage may be unexpectedly thrown out,

causing an accident.
In addition, exhaust gases may enter the

vehicle, causing death or a serious health

hazard. Make sure to close the power

back door before driving.

Never let anyone sit in the luggage

compartment. In the event of sudden

braking, sudden swerving or a colli-

sion, they are susceptible to death or

serious injury.

When children are in the vehicle

Observe the following precautions.

Failure to do so may result in death or

serious injury.

Do not allow children to play in the lug-

gage compartment.

If a child is accidentally locked in the lug-

gage compartment, they could have heat

exhaustion or other injuries.

Do not allow a child to open or close

the power back door.

Doing so may cause the power back

door to move unexpectedly, or cause the

child’s hands, arms, head, or neck to be

caught by the closing power back door.

Operating the power back door

Observe the following precautions.

Failure to do so may cause parts of the

body to be caught, resulting in death or

serious injury.

Remove any heavy loads, such as snow

and ice, from the power back door

before opening it. Failure to do so may

cause the power back door to sud-

denly shut again after it is opened.

When opening or closing the power

back door, thoroughly check to make

sure the surrounding area is safe.

If anyone is in the vicinity, make sure

they are safe and let them know that

the power back door is about to open

or close.

Use caution when opening or closing

the power back door in windy weather

as it may move abruptly in strong wind.

The power back door may suddenly

shut if it is not opened fully. It is more

difficult to open or close the back door

on an incline than on a level surface, so

beware of the back door unexpectedly

opening or closing by itself. Make sure

that the back door is fully open and

secure before using the luggage com-

partment.

114

3-2. Opening, closing and locking the doors

Smart access system with
push-button start

Carry the electronic key to enable this
function.

1

Locks all the doors

Check that the door is securely locked.

2

Unlocks all the doors

The doors cannot be unlocked for 3 sec-
onds after the doors are locked.

Wireless remote control

P.107

Door lock switch

P.111

Opening/closing the power back
door using the wireless remote
control

Press and hold the switch for approxi-
mately 1 second.

The power back door can be operated
whether it is locked

*

or unlocked.

Pressing the switch while the power back
door is opening/closing will stop the oper-
ation.
Pressing and holding the switch again for
approximately 1 second will operate the
power back door in the opposite direction.

WARNING

When closing the power back door,

take extra care to prevent your fingers,

etc., from being caught.

When closing the power back door,

make sure to press it lightly on its outer

surface. If the back door handle is used

to fully close the power back door, it

may result in hands or arms being

caught.

Do not pull on the back door spindle

(

P.122) to close the power back

door, and do not hang on the back

door spindle.

Doing so may cause hands to be caught

or the back door spindle to break, caus-

ing an accident.

If a bicycle carrier or similar heavy

object is attached to the power back

door, it may suddenly shut again after

being opened, causing someone’s

hands, arms, head or neck to be

caught and injured. When installing an

accessory part to the power back

door, using a genuine Lexus part is

recommended.

Unlocking and locking the
power back door from the out-
side

Unlocking and locking the
power back door from the inside

Opening/closing the power back
door

115

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

*

: Opening of the power back door when it

is locked can be disabled by a custom-
ized setting.

Opening/closing the power back
door from the inside

Press and hold the switch for approxi-
mately 1 second.

A buzzer will sound and the power back
door will automatically open or close.
However, if the power back door is locked,
it will not open.
Pressing the switch while the power back
door is opening/closing will stop the oper-
ation.
Pressing and holding the switch again for
approximately 1 second will operate the
power back door in the opposite direction.

Back door opener switch

Open

When the power back door is unlocked:
Press the back door opener switch.
When the power back door is locked:

While carrying an electronic key, press and
hold the back door opener switch.
A buzzer will sound and the power back
door will automatically open.
Pressing the switch while the power back
door is opening/closing will stop the oper-
ation.

Close

Press the

switch.

A buzzer will sound and the power back
door will automatically close.

Pressing the

switch while the power

back door is closing will stop the operation.
Pressing the switch again will open the
power back door automatically.

Close the back door and lock all
doors (close & lock function)

Press the

switch.

The power back door will close and all of
the doors will be locked at the same time.
A different buzzer than the normal one will

116

3-2. Opening, closing and locking the doors

sound and the power back door will begin
closing automatically. When the power
back door is closed, all of the doors will
lock simultaneously and operation signals
will indicate that all of the doors have been
locked.

If the

switch is pressed while the power

back door is closing, the operation will
stop.
Pressing the switch again will open the
power back door automatically.

Closing the power back door using
the back door handle

Lower the power back door using the
back door handle, then a buzzer will
sound and the power back door will
automatically close.

Hands Free Power Back Door (if
equipped)

1

While carrying an electronic key,
stand within the smart access sys-
tem with push-button start opera-

tion range, approximately 19.7 to
23.6 in. (50 to 60 cm) from the
rear bumper.

Kick sensor
Hands Free Power Back Door
operation detection area
Smart access system with
push-button start operation detec-
tion area (

P.125)

2

Perform a kick operation by mov-
ing your foot to within approxi-
mately 3.9 in. (10 cm) of the rear
bumper and then pulling it back.

Perform the entire kick operation
within 1 second.

The Hands Free Power Back Door
will not start operating while a foot is
detected under the rear bumper.

Operate the Hands Free Power
Back Door without contacting the
rear bumper with your foot.

If another electronic key is in the
cabin or luggage compartment, it
may take slightly longer than normal

A
B

C

117

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

for the operation to occur.

Kick sensor
Hands Free Power Back Door
operation detection area

3

When the kick sensor detects that
your foot is pulled back, a buzzer
will sound and the power back door
will automatically fully open/close.

If kick operation is performed again in the

middle of back door operating, the opera-

tion will stop.

Hands free close & lock function*
(vehicles with Hands Free Power
Back Door)

*

: This setting can be customized by your

Lexus dealer.

If the power back door is closed using a
Hands Free Power Back Door close
operation, all of the doors will be
locked at the same time.

A different buzzer than the normal one will
sound before the power back door begins
to close. The door lock operation signals
will operate to indicate that the power back
door has closed and all of the doors have
locked simultaneously.
If a Hands Free Power Back Door opera-
tion is performed while the power back
door is operating, the power back door will
stop.
If a Hands Free Power Back Door opera-

tion is performed again, the power back
door will open.

Luggage compartment lights

The luggage compartment lights turn on

when the back door is opened.

When the power switch is turned off, the

lights will go off automatically after 20

minutes.

Power back door operating conditions

If the following conditions are met with the

power back door operation enabled, the

power back door can be opened and

closed automatically.

When an electronic key is being carried

and the back door opener switch is
pressed

*

When the wireless remote control is
used

*

When the power switch is in ON mode,

the vehicle speed must be lower than 2

mph (3 km/h) and one of the following

conditions must be met in addition to the

above conditions:

• The parking brake is engaged.

• The brake pedal is depressed.

• The shift lever is in P.

*

: When the operation of the power back

door when it is locked has been disabled
by a customized setting, operate the
power back door after it has been
unlocked.

Close & lock function operating condi-

tions

This function can be operated when all of

the following conditions are met:
• An electronic key is not detected within

the vehicle.

• All of the doors other than the power

back door are closed.

• The power switch is off.

Hands Free Power Back Door operating

conditions (if equipped)

The Hands Free Power Back Door (kick

sensor) setting is on.

A
B

118

3-2. Opening, closing and locking the doors

When an electronic key is carried within

the operation range.

Hands free close & lock function oper-

ating conditions (vehicles with Hands

Free Power Back Door)

This function can be operated when all of

the following conditions are met:
• The hands free close & lock function set-

ting is on.

• The Hands Free Power Back Door oper-

ating conditions are met.

• An electronic key is not detected within

the vehicle.

• All of the doors other than the power

back door are closed.

• The power switch is off.

Back door closer

In the event that the power back door is left

slightly open, the back door closer will auto-

matically close it to the fully closed position.

The back door closer can function when

the power switch is in any mode.

The power back door can be opened

using the back door opener switch even if

the back door closer is operating.

Operation of the power back door

When the power back door begins to

operate, the emergency flashers will flash

and a buzzer will sound.

When the power back door is disabled,

the power back door will not operate but

can be opened and closed manually.

The power back door turns to manual

operation when the back door opener

switch is pressed while the power back

door is in an automatic opening/closing

operation.

If anything obstructs the power back

door while opening, a buzzer will sound

and the power back door will stop imme-

diately. If anything obstructs the power

back door while closing, a buzzer will

sound and the power back door will auto-

matically move slightly in the opposite

direction and then stop.

Back door reserve lock function

This function reserves the locking of the

power back door when the power back

door is open. If the following operations are

performed, all of the doors except the

power back door will lock and then the

power back door will lock when it is com-

pletely closed.

1

Close all of the doors, except the power

back door.

2

Perform an automatic closing operation

of the power back door and lock the

doors using the wireless remote control

(

P.107) or smart access system with

push-button start (

P.109) while the

power back door is closing.

Also, if the back door does not fully close

due to the operation of the jam protection

function, etc., while the back door is auto-

matically closing after a reserve lock opera-

tion is performed, the reserve lock function

is canceled and all the doors will unlock.

Situations in which the close & lock

function may not operate properly

In the following situations, the close & lock

function may not operate properly:

If the

switch on the lower part of the

power back door (

P.115) is pressed by

a hand which is holding an electronic key

If the

switch on the lower part of the

power back door (

P.115) is pressed

when the electronic key is in a bag, etc.

that is placed on the ground

If the

switch on the lower part of the

power back door (

P.115) is pressed

with the electronic key not near the vehi-

cle.

Situations in which the Hands Free

Power Back Door may not operate

properly (if equipped)

In the following situations, the Hands Free

Power Back Door may not operate prop-

erly:

When a foot remains under the rear

bumper

If the rear bumper is strongly hit with a

foot or is touched for a while

119

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

If the rear bumper has been touched for a

while, wait for a short time before

attempting to operate the Hands Free

Power Back Door again.

When standing excessively close to the

rear bumper

When an external radio wave source

interferes with the communication

between the electronic key and the vehi-

cle (

P.126)

When the vehicle is parked near metal, or

an external radio wave or electrical noise

source which affects the sensitivity of the

Hands Free Power Back Door, such as a

pay parking spot, gas station, electrically

heated road, fluorescent light, or metal

plate

When the vehicle is near a TV tower,

electric power plant, radio station, large

display, airport or other facility that gen-

erates strong radio waves or electrical

noise

When a large amount of water is applied

to the rear bumper, such as when the

vehicle is being washed or in heavy rain

When mud, snow, ice, etc. is attached to

the rear bumper

When the vehicle has been parked for a

while near objects that may move and

contact the rear bumper, such as plants

When an accessory is installed to the rear

bumper

If an accessory has been installed, turn the

Hands Free Power Back Door (kick sen-

sor) operation setting off.

RX450hL: When a tire other than the

spare tire is stored in the spare tire stor-

age area

Preventing unintentional operation of

the Hands Free Power Back Door (if

equipped)

When an electronic key is in the operation

detection area, the Hands Free Power Back

Door may operate unintentionally, so be

careful in the following situations:

When a large amount of water is applied

to the rear bumper, such as when the

vehicle is being washed or in heavy rain

When dirt is wiped off the rear bumper

When a small animal or small object, such

as a ball, moves under the rear bumper

When an object is moved from under the

rear bumper

If someone is swinging their legs while sit-

ting on the rear bumper

If the legs or another part of someone’s

body contacts the rear bumper while

passing by the vehicle

When the vehicle is parked near an elec-

trical noise source which affects the sen-

sitivity of the Hands Free Power Back

Door, such as a pay parking spot, gas sta-

tion, electrically heated road, or fluores-

cent light

When the vehicle is near a TV tower,

electric power plant, radio station, large

display, airport or other facility that gen-

erates strong radio waves or electrical

noise

When the vehicle is parked in a place

where objects such as plants are near the

rear bumper

If luggage, etc. is set near the rear

bumper

If accessories or a vehicle cover is

installed/removed near the rear bumper

When the vehicle is being towed

To prevent unintentional operation, turn the

Hands Free Power Back Door (kick sensor)

operation setting off.

When reconnecting the 12-volt battery

To enable the power back door to operate

properly, close the power back door manu-

ally.

Jam protection function

Sensors are installed in the right and left

sides of the power back door. When the

door is automatically closing and the sen-

sors are pushed due to an object being

caught, etc., the jam protection function will

operate.
From that position the door will automati-

cally move a little in the opposite direction

and then the function will stop.

120

3-2. Opening, closing and locking the doors

If the power back door opener is inoper-

ative

The power back door can be unlocked from

the inside

1

Remove the cover.

To protect the cover, place a rag between

the flathead screwdriver and cover as

shown in the illustration.

2

Move the lever.

Customization

Some functions can be customized.

(

P.472)

WARNING

Back door closer

In the event that the power back door

is left slightly open, the back door

closer will automatically close it to the

fully closed position. It takes several

seconds before the back door closer

begins to operate. Be careful not to get

fingers caught or anything else in the

power back door, as this may cause

bone fractures or other serious inju-

ries.

Use caution when using the back door

closer as it still operates when the

power back door system is disabled.

Power back door

Observe the following precautions when

operating the power back door.

Failure to do so may cause death or seri-

ous injury.

Check the safety of the surrounding

area to make sure there are no obsta-

cles or anything that could cause any

of your belongings to get caught.

If anyone is in the vicinity, make sure

they are safe and let them know that

the power back door is about to open

or close.

If the power back door system is dis-

abled while the power back door is

operating, the power back door will

stop operating. The power back door

must then be operated manually. Take

extra care in this situation, as the

power back door may open or close

suddenly.

121

3-2. Opening, closing and locking the doors

3

Be

fore
dri
ving

WARNING

If the operating conditions of the

power back door (

P.117) are no lon-

ger met, a buzzer may sound and the

power back door may stop opening or

closing. The power back door must

then be operated manually. Take extra

care on an incline in this situation, as

the power back door may move sud-

denly.

On an incline, the power back door

may suddenly shut after it opens. Make

sure the power back door is fully open

and secure.

In the following situations, the power

back door may detect an abnormality

and automatic operation may be

stopped. In this case, the power back

door must then be operated manually.

Take extra care in this situation, as the

stopped power back door may sud-

denly open or close, causing an acci-

dent.

• When the power back door contacts

an obstacle

• When the 12-volt battery voltage sud-

denly drops, such as when the power

switch is turned to ON mode or the

hybrid system is started during auto-

matic operation

If a bicycle carrier or similar heavy

object is attached to the power back

door, the power back door may not

operate, causing a malfunction, or the

power back door may suddenly shut

again after being opened, causing

someone’s hands, arms, head or neck

to be caught and injured. When install-

ing an accessory part to the power

back door, using a genuine Lexus part

is recommended.

Jam protection function

Observe the following precautions.

Failure to do so may cause death or seri-

ous injury.

Never use any part of your body to

intentionally activate the jam protec-

tion function.

The jam protection function may not

work if something gets caught just

before the power back door fully

closes. Be careful not to get fingers

caught or anything else.

The jam protection function may not

work depending on the shape of the

object that is caught. Be careful not to

catch fingers or anything else.

Hands Free Power Back Door (if

equipped)

Observe the following precautions.

Failure to do so may cause death or seri-

ous injury.

Check the safety of the surrounding

area to make sure there are no obsta-

cles or anything that could cause any

of your belongings to get caught.

Exhaust gasses cause the exhaust

pipes to become quite hot. When

operating the Hands Free Power Back

Door, be careful not to touch the

exhaust pipe.

Do not operate the Hands Free Power

Back Door if there is little space under

the rear bumper.

Была ли эта страница вам полезна?
Да!Нет
8 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности