Lexus LS400 (2000 year). Manual — part 30
Z14905
BE0CU–01
N13349
Z14753
Wire Harness Side
–
BODY ELECTRICAL
SEAT HEATER SYSTEM
BE–197
2060
INSPECTION
1.
INSPECT SEAT HEATER SWITCH CONTINUITY
Condition
Tester connection
Specified condition
OFF
–
No continuity
ON (Left)
8 – 9 – 11
Continuity
ON (Right)
8 – 11 – 13
Continuity
Illumination
10 – 12
Continuity
If continuity is not as specified, replace the switch or bulb.
2.
INSPECT SEAT HEATER SWITCH INDICATOR
(a)
Connect the positive (+) lead from the battery to terminal
11 and the negative (–) lead to terminal 8.
(b)
Push the switch and check that the indicator light lights
up.
If operation is not as specified, replace the switch.
3.
INSPECT SEAT HEATER SWITCH CIRCUIT
Disconnect the switch connector and inspect the connector on
the wire harness side, as shown.
Tester connection to
terminal number
Condition
Specified condition
8 – Ground
Constant
Continuity
9 – Ground
Constant
* Continuity
13 – Ground
Constant
* Continuity
11 – Ground
Ignition switch turned to ON
Battery positive voltage
*: There is resistance because this circuit is grounded through
the relay coil.
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
Z08901
BE4730
BE–198
–
BODY ELECTRICAL
SEAT HEATER SYSTEM
2061
4.
INSPECT ENGINE MAIN RELAY CONTINUITY
Condition
Tester connection
Specified condition
Constant
1 – 3
2 – 4
Continuity
Apply B+ between
terminals 1 and 3.
4 – 5
Continuity
If continuity is not as specified, replace the relay.
5.
INSPECT ENGINE MAIN RELAY CIRCUIT
Remove the relay and inspect the connector on the junction
block side, as shown.
Tester connection
Condition
Specified condition
2 – Ground
Constant
Continuity
3 – Ground
Constant
Continuity
1 – Ground
Ignition switch ON
Battery positive voltage
5 – Ground
Constant
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
Z14754
Seat Cushion Side
Connector ”A”
Connector ”B”
Z14755
Seat Back Side
–
BODY ELECTRICAL
SEAT HEATER SYSTEM
BE–199
2062
6.
Seat Cushion:
INSPECT SEAT HEATER CONTINUITY
(a)
Heat the thermostat with a light.
(b)
Inspect the seat heater continuity between terminals.
Tester connection
Condition
Specified condition
A2 – B3
Constant
Continuity
A1 – B1
Seat heater temperature bellow 25
°
C (77
°
F)
Continuity
B1 – B2
Seat heater temperature bellow 25
°
C (77
°
F)
Continuity
A1 – B2
Seat heater temperature bellow 25
°
C (77
°
F)
Continuity
A1 – B1
Seat heater temperature above
55
°
C (131
°
F)
No continuity
B1 – B2
Seat heater temperature above
45
°
C (113
°
F)
No continuity
A1 – B2
Seat heater temperature above
45
°
C (113
°
F)
No continuity
If continuity is not as specified, replace the seat cushion pad.
7.
Seat Back:
INSPECT SEAT HEATER CONTINUITY
Inspect the seat heater continuity between terminals, as
shown.
Tester connection
Condition
Specified condition
1 – 3
Constant
Continuity
2 – 3
Constant
Continuity
If continuity is not as specified, replace the seat back pad.
BE0CV–01
I03237
Fuel Lid Opener Switch
Instrument Panel Junction Block
FUEL OPN Fuse
Fuel Lid Opener Solenoid
BE–200
–
2063
FUEL LID OPENER SYSTEM
LOCATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст