Lexus ES300 (1997 year). Manual — part 114
V08431
ALL METERS, GAUGES, AND
ILLUMINATIONS
ALL METERS, GAUGES, AND
ILLUMINATIONS
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Disconnect connector ”B” from meter.
Inspect connector on wire harness side as follows.
Replace circuit plate. Then recheck system.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
No
Yes
4
5
Brightness does not change even
when light control switch is operated.
(OFF
↔
TAIL)
Brightness does not change even when
rheostat volume is turned.
RHEOSTAT LIGHT
CONTROL VOLUME
COMBINATION
METER
COMBINATION
METER
Yes
No
Yes
No
INSPECT TAILLIGHT SIGNAL CIRCUIT
Does voltage change between terminal B8 and
ground as follows?
Taillight signal circuit faulty on vehicle side.
Inspect illumination light system.
Battery positive voltage
Replace rheostat light control volume.
Then recheck system.
Wire harness faulty between terminal D1 of meter
and terminal D2 of rheostat volume and rheostat
light control.
Condition
Voltage
Light control
switch
position
OFF
No voltage
TAIL or HEAD
INSPECT RHEOSTAT LIGHT CONTROL VOLUME
(See page BE–)
Is operation normal?
Connect connector to rheostat volume.
Disconnect connector ”D” from meter.
Inspect connector on wire harness side as follows.
Turn ignition switch ON. Does voltage change
evenly between terminal D1 and D2 when rheostat
knob is turned?
Replace circuit plate. Then recheck system.
BE–62
–
BODY ELECTRICAL
COMBINATION METER
1446
1997 LEXUS ES300 (RM511U)
V08432
ALL METERS, GAUGES, AND
ILLUMINATIONS
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Disconnect connector ”B” from meter.
Inspect connector on wire harness side as follows.
Replace circuit plate. Then recheck system.
6
7
SPEEDOMETER
Does not go out while starter running.
Speedometer does not operate while
driving
Replace circuit plate. Then recheck system.
No
Yes
COMBINATION
METER
Yes
Yes
Yes
No
No
No
Wire harness faulty between terminal B16 of Meter
and ST fuse.
Turn ignition switch START.
Is there battery positive voltage between terminal and
ground or B16?
Does odometer operate while driving?
Does trip meter operate while driving?
CONTINUED ON NEXT PAGE
Jack up the vehicle.
Turn ignition switch ON. Rotate propeller shaft.
Does the voltage between terminals C9 and C10
change (approx. 0V to 11V or more) per revolution of
propeller shaft?
Disconnect connector ”C” from meter.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
INSPECT TRIP METER OPERATION
INSPECT ODOMETER OPERATION
Replace speedometer.
Then recheck system.
Go to step 7–A
–
BODY ELECTRICAL
COMBINATION METER
BE–63
1447
1997 LEXUS ES300 (RM511U)
V08433
8
SPEEDOMETER
Replace circuit plate. Then recheck system.
COMBINATION
METER
Yes
No
Does odometer operate while driving?
Jack up the vehicle. Turn ignition switch ON.
Rotate propeller shaft. Does the voltage between
terminals C10 and ground change (approx. 0V to 5V
or more) per revolution of propeller shaft?
Disconnect connectors ”A” and ”C” from meter.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
INSPECT ODOMETER OPERATION
See chart 18.
ECM
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Replace circuit plate. Then recheck system.
Remove meter with connector connected.
Inspect connector ”C” from back side as follows.
Wire harness between terminal C10 of meter and*ECU
faulty.
Power Steering ECU
* : An electrical tester availble to measure frrequency
is necessary for this inspection.
REFERENCE : TOYOTA ELECTRICAL TESTER
(09082–00050)
Suspension ECU
ABS and TRAC ECU
With engine running, does voltage between terminals
A13 and C10 fluctuate?
Cruise Control ECU
Yes
No
9
Vehicle speed signal (4P) faulty
Tachometer dose not operate while
engine running.
TACHOMETER
Yes
No
* INSPECT TACHOMETER CIRCUIT
Wire harness faulty between terminal A13 of meter
and igniter.
BE–64
–
BODY ELECTRICAL
COMBINATION METER
1448
1997 LEXUS ES300 (RM511U)
V08434
COMBINATION METER
Yes
No
Disconnect connector ”D” from meter.
Inspect connector on wire harness side as follows.
HINT : While carrying out the following inspection, make certain that the connectors and terminals are properly con-
nected.
Yes
Yes
Yes
No
No
No
Is operation normal?
Replace receiver gauge. Then recheck system.
Is there continuity (no resistance ) between terminal
D12 and ground?
Are speedometer and tachometer operating normally?
Replace combination
meter computer.
Then recheck system.
Open circuit in wire
harness between terminal
12 of meter and ground.
Ground faulty.
Wire harness faulty between meter and sender gauge.
Replace sender gauge. Then recheck system.
Is operation normal?
Is resistance normal?
Replace combination meter computer.
Then recheck system.
INSPECT SENDER GAUGE OPERATION
(See page
INSPECT RECEIVER GAUGE RESISTANCE
(See page
INSPECT RECEIVER GAUGE OPERATION
(See page
FUEL GAUGE
Does not operate or operation is
abnormal.
10
Yes
No
–
BODY ELECTRICAL
COMBINATION METER
BE–65
1449
1997 LEXUS ES300 (RM511U)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст