Lexus ES300 (1997 year). Manual — part 147
BO09Y–03
N21403
N21404
N21401
–
BODY
FUEL LID
BO–41
1219
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
REMOVE THESE PART:
(a)
Luggage compartment floor mat
(b)
Rear floor finish plate
(c)
LH rear floor finish side plate
(d)
Inner LH cover luggage compartment trim
2.
REMOVE FUEL LID LOCK ASSEMBLY
(a)
Remove the nut from the fuel lid side.
(b)
Remove the nut and lock assembly, then disconnect the
connector.
3.
REMOVE FUEL INLET PIPE SHIELD
(a)
Remove the ring.
(b)
Remove the fuel tank cap and shield.
CAUTION:
Always keep the tank cap closed when it is not re-
quired to be open.
Keep all fire away during the operation.
(c)
Install the cap quickly.
4.
REMOVE FUEL FILLER OPENING LID
(a)
Using a drill, drill out the rivet heads.
(b)
Remove the fuel filler opening lid.
(c)
Remove the fuel tank cap hanger and lock retainer from
the opening lid.
BO09Z–01
N21401
BO–42
–
BODY
FUEL LID
1220
1997 LEXUS ES300 (RM511U)
INSTALLATION
1.
INSTALL THESE PARTS:
(a)
Fuel inlet pipe shield
(b)
Fuel tank cap
(c)
Ring
(d)
Fuel lid lock assembly
Torque: 5.5 N·m (56 kgf·cm, 49 in.·lbf)
2.
INSTALL FUEL FILLER OPENING LID
(a)
Install the fuel tank cap hanger to the opening lid.
(b)
Install the nut and fuel filler opening lid lock retainer to the
opening lid.
Torque: 5.5 N·m (56 kgf·cm, 49 in.·lbf)
(c)
Using a riveter, install the 2 rivets to the fuel filler opening
lid.
3.
INSTALL THESE PARTS:
(a)
Inner LH cover luggage compartment trim
(b)
Rear floor finish side plates
(c)
Rear floor finish plate
(d)
Luggage compartment floor mat
BO0A0–03
N21846
N·m (kgf·cm, ft·lbf) : Specified torque
Wiper Arm and Blade
RH Cowl Top
Ventilator Louver
Hood to Cowl
Top Seal
Wiper Motor
Wiper Link Assembly
Hood Insulator
x 9
Window Washer Hose
Washer Tank
LH Cowl Top
Ventilator Louver
24 (245, 18)
7.0 (71, 62 in.·lbf)
–
BODY
FRONT WIPER AND WASHER
BO–43
1221
1997 LEXUS ES300 (RM511U)
FRONT WIPER AND WASHER
COMPONENTS
BO0A1–01
N13516
N21409
N21410
BO–44
–
BODY
FRONT WIPER AND WASHER
1222
1997 LEXUS ES300 (RM511U)
REMOVAL
1.
REMOVE WIPER ARM AND BLADE ASSEMBLY
2.
REMOVE COWL TOP VENTILATOR LOUVER
(a)
Remove the hood to cowl top seal.
(b)
Remove the 2 clips and cowl top ventilator louver.
HINT:
Raise the front side of the cowl top ventilator louver up and re-
move the cowl top ventilator louver.
3.
REMOVE WIPER MOTOR AND LINK ASSEMBLY
(a)
Remove the 4 bolts.
(b)
Disconnect the connector, then unfasten the bolt.
(c)
Raise the front side of the wiper motor and link assembly
up and remove the wiper motor and link assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст