Lexus SC300 / Lexus SC400. Manual — part 410
24. CONNECT IGNITER CONNECTOR
(a) Connect the two igniter connectors.
(b) Install the wire clamp.
25. INSTALL
RADIATOR
(a) Install the two lower radiator supports to the radiator.
(b) Place the radiator on the body bracket.
(c) Slightly lift the radiator, and connect the two cooler hose
(for cooling fan) to the hose clamp on the radiator fan
shrould.
(d) Install the upper radiator support with the two bolts and
screw. Install the two upper radiator supports.
(e) Connect the following hoses:
(1) Pressure hose to hydraulic pump
(2) Suction hose to hydraulic pump
EM–174
–
ENGINE MECHANICAL
Cylinder Block
(3) Two oil cooler hoses (for A/T) to radiator
(4) Two radiator hoses
(5) Two oil cooler hoses (for cooling fan) to pipes
(f) Connect the water temperature sensor connector.
(g) Install the wire clamp (for water temperature sensor) to
the radiator fan shrould.
26. INSTALL
RADIATOR
RESERVOIR
TANK
(a) Install the reservoir tank to the reservoir tank bracket.
(b) Install the reservoir tank bracket with the two bolts.
–
ENGINE MECHANICAL
Cylinder Block
EM–175
(c) Connect the following hoses:
(1) Reservoir hose to water inlet housing
(2) Reservoir hose to radiator
(d) Connect the coolant level sensor connector.
27. INSTALL INTAKE AIR CONNECTOR
(a) Connect the intake air connector to the throttle body.
(b) Install the hose clamp and mounting bolt.
(c) Connect the following hoses:
(1) Air hose to ISC valve
(2) Air hose (from PS air control valve) to air intake
chamber
28. CONNECT VACUUM HOSE (A) (FROM PS AIR CONTROL
VALVE) TO AIR INTAKE CHAMBER
29. INSTALL AIR CLEANER AND AIR FLOW METER
(a) Connect the air cleaner case to the air duct.
(b) Connect
the air cleaner hose to the intake air connector.
(c) Install the four mounting bolts and hose clamp.
(d) Connect the air flow meter connector.
30. CONNECT CONTROL CABLES TO THROTTLE BODY
Connect the following cables:
(1) Accelerator
cable
(2) A/T throttle cable
(3) (w/ Cruise Control System)
Cruise control actuator cable
EM–176
–
ENGINE MECHANICAL
Cylinder Block
31. INSTALL THROTTLE BODY COVER
Install the throttle body cover and hose clamp with the two
bolts and cap nut.
32. INSTALL DRIVE BELT
Install the drive belt by turning the drive belt tensioner coun-
terclockwise.
HINT: The pulley bolt for the belt tensioner has a left–hand
thread.
33. INSTALL
BATTERY
34. FILL WITH ENGINE COOLANT (See page
35. FILL COOLING FAN RESERVOIR TANK WITH FLUID
(See page
)
36. FILL WITH ENGINE OIL (See page
Capacity:
Drain and refill
w/Oil filter change
4.8 liters (5.1 US qts, 4.2 lmp. qts)
w/o Oil filter change
4.5 liters (4.8 US qts, 4.0 lmp. qts)
Dry fill 6.0 liters (6.3 US qts, 5.3 lmp. qts)
37. START ENGINE AND CHECK FOR LEAKS
38. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
39. CHECK IGNITION TIMING (See page
Ignition timing:
8–12
°
BTDC @ idle
(w/ Terminals TE1 and E1 connected)
40. INSTALL ENGINE UNDER COVER
41. INSTALL
HOOD
42. PERFORM ROAD TEST
Check for abnormal noise, shock, slippage, correct shift
points and smooth operation.
32. RECHECK
ENGINE COOLANT AND ENGINE OIL LEVELS
–
ENGINE MECHANICAL
Cylinder Block
EM–177
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст