Lexus SC300 / Lexus SC400. Manual — part 130
Hood Hinge
REMOVAL AND INSTALLATION
(See page
HINT:
Install the hinge by following removal sequence in
reverse.
1. REMOVE
HOOD
Removal:
(See steps 1 to 2 on page
Installation: (See steps 1 to 2 on page
2.
REMOVE FRONT BUMPER
Removal:
(See steps 1 to 6 on page
Installation: (See
)
3.
REMOVE FRONT FENDER
Removal:
(See steps 1 to 4 on page
Installation: (See steps 1 to 4 on page
4.
REMOVE COWL LOUVER
5.
REMOVE HOOD HINGE
Remove two bolts and the hinge.
Hood Support
REMOVAL AND INSTALLATION
(See page
1.
REMOVE SUPPORT FROM HOOD
Remove the bolt and the support from hood.
HINT:
While supporting the hood with your hand, remove
the hood.
2.
REMOVE SUPPORT FROM BODY
Remove the bolt and the support.
3.
IF NECESSARY, REPLACE HOOD SUPPORT
NOTICE: Handling the damper.
(a) Do not disassemble the damper as the cylinder is filled
with pressurized gas.
(b) If
the
damper
is
to
be
replaced, drill a 2.0 – 3.0 mm
(0.079–0.118 in.) hole in the bottom of the removed
damper cylinder to completely release the high–pressure
gas before disposing of it.
(c) When drilling, chips may fly out so work carefully.
(d) The gas is colorless, odorless and non–toxic.
(e) When working, handle the damper carefully. Never score
or scratch the exposed part of the piston rod, and never
allow paint or oil to get on it.
(f)
Do not turn the piston rod and cylinder with the damper
fully extended.
4.
INSTALL HOOD SUPPORT
Install the support.
Torque:
22 N
⋅
m (225 kgf
⋅
cm 16 ft
⋅
lbf)
–
BODY
Hood (Hood–Related Parts)
BO–23
Hood Lock Control
COMPONENTS
Front Bumper
BO–24
–
BODY
Hood (Hood Lock Control)
REMOVAL OF HOOD LOCK CONTROL
(See page
1.
REMOVE FOLLOWING PARTS:
(a) Front
bumper
(b) LH front fender wheel opening moulding
(c) LH fender liner
(d) Fender splash shield
(e) Hood release lever
2.
REMOVE HOOD LOCK
(a) Remove two bolts, the nut and the hood lock.
(b) Disconnect the link from the lock.
3.
REMOVE HOOD LOCK CONTROL CABLE
(a) Disconnect the cable from clamps.
(b) Using the screwdriver, pry out the cable stopper from
grommet.
HINT:
Do not damage the grommet with the screwdriver.
–
BODY
Hood (Hood Lock Control)
BO–25
(c) Pull the cable from front wheel housing to remove it.
INSTALLATION OF HOOD LOCK
CONTROL
(See page
1. BEFORE INSTALLING PARTS, COAT LOCK WITH MP
GREASE
Apply MP grease to the sliding surface of the lock.
2.
INSTALL HOOD LOCK CONTROL CABLE
(a) Push the rear side cable through the grommet.
(b) Using the screwdriver, push the cable stopper into the
grommet.
HINT:
Do not damage the grommet with the screwdriver.
(c) Clamp the cable to the junction block.
(d) Pass the front side cable through the upper radiator
support.
3.
INSTALL HOOD RELEASE LEVER
4.
INSTALL HOOD LOCK TEMPORARILY
5. CHECK HOOD LOCK CONTROL FOR PROPER
OPERATION
After checking for proper operation, tighten the nut and two
bolts to install the lock.
6.
INSTALL FOLLOWING PARTS:
(a) Hood release lever
(b) Fender splash shield
(c) LH fender liner
(d) LH front fender wheel opening moulding
(e) Front
bumper
BO–26
–
BODY
Hood (Hood Lock Control)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст