Mercedes-Benz ML320. Manual — part 477
Fig. 26: Identifying Thrust Piece (124 589 02 34 00)
Fig. 27: Identifying Puller (001 589 50 33 00)
Fig. 28: Identifying Clamping Pliers (140 589 01 34 00)
1. Screw clamping pliers to puller and tighten.
2. Clamp front axle shaft flange in vise with aluminum jaws.
3. Place thrust piece (010e) with large diameter on front axle shaft flange.
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Fig. 29: Identifying Thrust Piece & Axle Shaft Flange
4. Insert complete puller over inner bearing race. Clamp tensioning pliers around upper grooves using
conical sleeve of puller.
5. Pull off and remove bearing inner race from front axle shaft flange using puller.
Fig. 30: Identifying Front Axle Shaft Flange
REMOVE/INSTALL FRONT AXLE SHAFT FLANGE AND DOUBLE-ROW ANGULAR BALL BEARING - AR33.20-P-0315GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
Shown on vehicle with floating caliper
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Fig. 31: Identifying Front Axle Shaft Flange And Double-Row Angular Ball Bearing Components
Modification notes
7.8.00
Pulling out front axle
shaft flange, changed
Step 2:
The front axle shaft flange is now pulled out using a
stationary press and not with the auxiliary hydraulic
press.
AR33.20-P-
0315-01GI
Remove/Install
1
Remove steering knuckle
AR33.25-P-
0400GH
2
Pull out front axle shaft flange (9)
AR33.20-P-
0315-01GI
Extractor tool
Fig. 19
Extraction and insertion tool
Fig. 20
3
Detach circlip (9p)
Installation: Ensure that the circlip
seats securely in the wheel carrier.
Pliers for locking ring
*WH58.30-Z-
1009-02A
4
Pull double-row angular ball bearing
(9n) out of steering knuckle
AR33.20-P-
0315-03GH
Extraction and insertion tool
Fig. 20
AR33.20-P-
0315-04GH
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Test values for wheel location, wheel hub
Fig. 32: Identifying Extraction Tool (202 589 04 43 00)
Fig. 33: Identifying Extraction And Installation Tool (140 589 08 43 00)
5
Pulling inner bearing race off front
axle shaft flange
Thrust piece
Fig. 26
Puller
Fig. 27
Tensioning clamp
Fig. 28
Inspect
6
Check lateral and radial runout of
front axle shaft flange (9)
Following predefined repair plan.
Permissible lateral runout
*BE33.20-P-
1001-01B
Permitted vertical runout
If readings are lower than specification,
it may be necessary to: ?
Replace front axle shaft flange.
*BE33.20-P-
1002-01B
7
Install in the reverse order
Number
Designation
Model Series
163
BE33.20-P-1001-
01B
Permissible lateral runout of front axle shaft flange when removed mm 0.03
BE33.20-P-1002-
01B
Permissible radial runout of front axle shaft flange at center
centering when removed
mm 0.03
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст