Mercedes-Benz ML320. Manual — part 830
AR01.20-P-5014-02C
Remove/install cylinder head cover trim
Crankcase ventilation, cylinder head cover
Number
Designation
Engine
613.960/
961
BA01.20-P-1002-01A
Screw of trim panel of cylinder head cover
to cylinder head cover
Nm
10
BA01.20-P-1003-01A
Screw attaching cover panel to charge air
distribution pipe
Nm
10
Crankcase ventilation, cylinder head cover
Number
Designation
Engine
648
BA01.20-P-1002-01G
Bolt, trim panel of cylinder
head cover to cylinder head
Nm
9
BA01.20-P-1003-01G
Bolt, cover charge air
distribution pipe
Nm
9
P01.20-2017-11
1
Unscrew bolts (3, 4).
Installation: Pay attention to tightening torques
.
2
Pull out trim panel (2) of charge air distribution pipe to the side.
Installation: Insert plates of trim panel (2) into the rubber
mounts (5).
3
Take off trim panel (1) of cylinder head cover.
Installation: Ensure the trim panel is correctly installed;
ensure no lines are trapped.
4
Install in the reverse order.
Copyright DaimlerChrysler AG 28.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
GF54.50-P-4101GH
Electronic compass, location/purpose/design
24.3.00
MODEL
163 as of 1.9.00 with CODE (245) Trip computer
P54.50-2035-06
B26 Electronic compass
Electronic compass, location
The electronic compass (B26) can be found
below the cover for the trunk sill.
Electronic compass, purpose
GF54.50-P-4101-01GH
Electronic compass, design
The electronic compass (B26) is housed in a
plastic casing. The two measuring coils are
mounted perpendicular to one another on a
circuit board. The 4-pin connector is
connected to the electronic compass (B26)
via a piece of cable.
Copyright DaimlerChrysler AG 18.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
GF54.50-P-4101-01GH
Electronic compass, purpose
n
The electronic compass (B26) determines the current route of the
vehicle using the earth's magnetic field and passes the appropriate
data to the trip computer control module (N41) via a two-wire
interface (RS485).
The compass has a calibration mode to allow the route to be
determined as accurately as possible. In this mode the compass can
be adapted to the magnetic conditions around the vehicle.
Copyright DaimlerChrysler AG 18.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
GF54.50-P-4100-02GH
Trip computer control module, design
n
The trip computer control module (TRIP, N41) consists of the
following components:
D
Electronics unit
D
LCD display
D
Reset button (left button, N41s1)
D
Mode button (right button, N41s2)
D
Inclination sensor (N41b1)
D
Glass breakage sensor (N41b2)
D
CAN interface
D
Alarm bus to all activity module (AAM, N10)
D
as of 1.9.00: Interface (RS 485) to electronic compass (B26)
Copyright DaimlerChrysler AG 18.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст