Mercedes-Benz ML320. Manual — part 480
Wheel location, hub
Fig. 50: Identifying Press (163 589 03 43 00)
Fig. 51: Identifying Support (163 589 01 43 00)
6
Detach upper transverse control
arm (6) from vehicle frame
Installation: Gently tighten the new nuts,
continuing until they seat. Wait until the
vehicle is resting on its road wheels before
tightening the bolts.
*BA33.20-P-
1006-01D
7
Install in the reverse order
8
Perform chassis alignment check
AR40.20-P-
0200GH
Number
Designation
Model Series
163
BA33.20-P-1001-
01D
Self-locking nut, upper wishbone follower joint to steering
knuckle
NM 50
BA33.20-P-1006-
01D
Bolt, upper wishbone to frame
NM 120
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Fig. 52: Identifying Thrust Piece (129 589 10 63 00)
REMOVE/INSTALL LOWER WISHBONE - AR33.20-P-0510GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
Fig. 53: Identifying Lower Wishbone Components
Remove/Install
Notes on self-locking nuts and bolts All models
AH00.00-N-
0001-01A
1
Remove front springs
AR32.20-P-
0200GH
2
Remove steering knuckle
AR33.25-P-
0400GH
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Front axle torsion strut
Wheel location, hub
REPLACE FRONT BEARING OF LOWER WISHBONE - AR33.20-P-0526GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
3.1
Remove linkage rod for suspension-
control module (95b) from lower
right control arm
Vehicles with xenon headlamps.
4
Detach torsion bar (28) from lower
control arm
*BA32.20-P-
1002-02G
5
Detach lower control arm (4) from
front subframe
Installation: Tighten new nuts slightly.
Tighten bolt fully only when vehicle is on
its wheels and ready to drive.
*BA33.20-P-
1004-01D
6
Loosen clamped joint at rear of
lower wishbone (4) and fold down
bearing shell (4d)
Installation: Tighten new nuts slightly.
Tighten bolt fully only when vehicle is on
its wheels and ready to drive.
*BA33.20-P-
1005-01D
Inspect
7
Inspect lower control arm for signs
of distortion and corrosion
8
Install in the reverse order
9
Perform chassis alignment check
AR40.20-P-
0200GH
Number
Designation
Model Series 163
BA32.20-P-1002-02G
Bolt, torsion bar to wishbone
NM 68
Number
Designation
Model Series 163
BA33.20-P-1004-01D
Bolt, lower wishbone at front to front axle carrier
NM 135
BA33.20-P-1005-01D
Bolt, lower wishbone at rear to front axle carrier
NM 30
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Fig. 54: Identifying Lower Wishbone Front Bearing Replacement For Rubber Bushing
Fig. 55: Identifying Extraction And Insertion Tool (163 589 00 43 00)
Repair materials
REMOVING AND INSTALLING STEERING KNUCKLE - AR33.25-P-0400GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
Remove
1
Remove lower control arm
AR33.20-P-
0510GH
2
Use thrust fitting (012n) to press rubber bushing (4k)
from lower control arm
Extraction and
insertion tool
Fig. 55
Install
3
Place rubber bushing (4k) in tapered sleeve (012p) and
use thrust fitting (012n) to press it into the center of the
lower control arm
Coat rubber mount
with liquid lubricant.
*BR00.45-Z-
1010-06A
Extraction and
insertion tool
Fig. 55
4
Install lower control arm
AR33.20-P-
0510GH
Number
Designation
Order number
BR00.45-Z-1010-06A
Antifriction agent
A 000 989 03 67
2001 Mercedes-Benz ML320
1998-2005 DRIVELINE/AXLES Front Axle - 163 Chassis
me
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст