Mercedes-Benz ML320. Manual — part 90
187
Controls in detail
Useful features
Compass
The compass displays the direction the ve-
hicle is traveling. The display 3 will show
you N, NE, E, SE, S, SW, W or NW.
To ensure the display is correct, the com-
pass must be set to the proper geographic
zone (
컄
page 188). It may also be neces-
sary to calibrate the compass
(
컄
page 188).
Zone map North America
Zone map South America
i
The presence of buildings, bridges,
power lines and large antenna masts
can influence the displayed values. Me-
tallic or magnetic objects in or on the
vehicle can influence the accuracy of
the compass.
188
Controls in detail
Useful features
Setting the compass zone
왘
Determine the geographical point of
the vehicle with the aid of the zone
maps.
왘
Switch on the ignition.
왘
Press MODE 2 (
컄
page 186) repeat-
edly until the compass display appears
in the trip computer display 3.
왘
Press RESET 1 (
컄
page 186) to select
the compass zone mode.
The zone selected last is shown in the
display.
왘
Press RESET 1 repeatedly until the
correct compass zone, as determined
from the zone map, is shown in the dis-
play.
왘
Press MODE 2 twice.
The new compass zone is activated and
the compass display will be shown.
Calibrating the compass
If the vehicle was exposed to a significant
magnetic zone, such as high voltage power
lines, the compass may have to be calibrat-
ed.
To calibrate the compass correctly, ob-
serve the following:
앫
Calibrate the compass in an area free
of steel superstructures and power
lines.
앫
Switch off all electrical consumers (e.g.
exterior lamps, climate control, rear
window defroster etc.).
앫
Do not open or close the
sliding/pop-up roof.
앫
Close doors and liftgate.
왘
Start and run the engine.
왘
Press MODE 2 (
컄
page 186) repeat-
edly until the compass display appears
in the trip computer display 3.
왘
Press RESET 1 and afterwards press
MODE 2.
In the display appears
CAL–
.
왘
Press and hold RESET 1 for approxi-
mately two seconds.
The calibration mode is activated and
the display shows
CAL
.
왘
Drive without interruption two full cir-
cles at a speed between 3 mph
(5 km/h) and 7 mph (10 km/h).
The message
CAL
goes out after a short
time. The calibration is now complete.
i
An open liftgate triggers the
display
- - -
.
189
Controls in detail
Useful features
Stop watch
왘
Press MODE 2 (
컄
page 186) repeat-
edly until the stop watch display ap-
pears in the trip computer display 3.
Counting
왘
Press RESET 1 (
컄
page 186) to start
counting.
Stopping
왘
Press RESET 1 again to stop counting.
Resetting
왘
Press and hold RESET 1 until the dis-
play shows “0:00”.
Average fuel consumption
왘
Press MODE 2 (
컄
page 186) repeat-
edly until the average fuel consumption
display appears in the trip computer
display 3.
Distance remaining with fuel presently
in tank
왘
Press MODE 2 (
컄
page 186) repeat-
edly until the distance remaining dis-
play appears in the trip computer
display 3.
i
If
CAL
remains in the display, calibration
was not successfully completed. You
have to recalibrate:
앫
Remove the key from the steering
lock.
앫
Start the vehicle and start the cali-
bration procedure described previ-
ously.
We recommend that you have the com-
pass calibrated at a Mercedes-Benz
Light Truck Center.
i
When the fuel supply drops to reserve
level the display flashes distance re-
maining.
앫
USA only:
The display alternates between
FUEL
and distance remaining until
supply is consistently below the re-
serve level. When the fuel supply is
very low [approximately 1.5 gal
(5.5 l)]
FUEL
is displayed
continuously.
190
Controls in detail
Useful features
Country
왘
Press MODE 2 (
컄
page 186) repeat-
edly until the country display appears
in the trip computer display 3.
왘
Press and hold RESET 1 a minimum of
five seconds to change the country unit
system.
Canada units system selection
You can choose between CAN-English or
CAN-French.
Setting CAN-English
왘
Press RESET 1 repeatedly until CAN is
displayed.
왘
Press MODE 2 to select
–ENG
.
왘
Press MODE 2 again to set CAN-En-
glish.
Setting CAN-French
왘
Press RESET 1 repeatedly until CAN is
displayed.
왘
Press MODE 2.
–ENG
is displayed.
왘
Press RESET 1 to select
–Fr
.
왘
Press MODE 2 to set CAN-French.
The language selected determines how the
various displays are presented, see table.
Display
Language
Date
Cardinal points
Fuel consumption
Distance remaining
GEr
German
DD.MM
Süd, Nord, Ost, West
l/100 km
Kilometer
GB
English
MM.DD
South, North, East, West mi/gal (Imperial)
Miles
ESP
Spain
DD.MM
Sur, Norte, Este, Oeste
l/100 km
Kilometer
Fr
French
DD.MM
Sud, Nord, Est, Ouest
l/100 km
Kilometer
USA
American
MM.DD
South, North, East, West mi/gal (US)
Miles
CAN-ENG
American
MM.DD
South, North, East, West l/100 km
Kilometer
CAN-Fr
French
DD.MM
Sud, Nord, Est, Ouest
l/100 km
Kilometer
GEr
German
DD.MM
Süd, Nord, Ost, West
l/100 km
Kilometer
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст